HOW TO ASIGN DUAL NUMBER ON BC11SP11/R1A

[7511066504]

HALLO, I WANT TO CONECT AN EURO NTBA TO PBX VIA EXTENTION PORT AND THAN ONE DBC213 AND ISDN MODEM
BEST REGARDS!

 

[Isinor]

Hi,

If it’s Dual Access ISDN that your after…

Note: ELU28/3 must have access to 32 time slots, when used as DUAL ACCESS.

Initiate Dual Access…
KSEXIIR=1000,CAT=1,EQU=1-1-10-00,ITYPE=20,ACCTYP=1;
ITNUIIR=1001,EQU=1-1-10-00,CAT=5;

Regards
Isinor

 

[7511066504]

THANKS FOR THE ANSWER BUT SEE WHAT HAPEND WHEN I SEND
<KSEXIIR=7733,EQU=2-1-70-01,CAT=1,ITYPE=20,ACCTYP=1;
THE ANSWER WAS
NOT ACCEPTED
EQUIPMENT POSITION ALREADY ASSIGNED
<SYEDP:BPOS=2-1-70;
SYSTEM EQUIPMENT DATA
EQU BOARDID TYPE DIR ROU/TRU
002-1-70-00 77 KL1 7016
002-1-70-02 77 KL1 7018
002-1-70-03 77 KL1 7019
002-1-70-04 77 KL1 7922
002-1-70-05 77 KL1 7783
002-1-70-06 77 KL1 7022
002-1-70-07 77 KL1 7845
002-1-70-08 77 KL1 7024
002-1-70-09 77 KL1 7025
002-1-70-10 77 KL1 7026
002-1-70-11 77 KL1 7041
002-1-70-12 77 KL1 7600
002-1-70-13 77 KL1 7601
002-1-70-14 77 KL1 7004
002-1-70-15 77 KL1 7604
END

 

[whosrdaddy]

look at position 2-1-72, it must be free

post CNLIPEV=YES; and CNBIP:BPOS=2-1-70; here

-----------------------------------------------------
What You See Is What You Get
Never underestimate tha powah of tha google!

 

[7511066504]

AT 2-1-72 IS vsu
LIM NUMBER 2
LIM CONTROL LIM CONTROL NUMBER OF SERVICE
SYSTEM SIDE SYSTEM STATE PCM-LINKS STATE LIM
A EXECUTING 2 ACTIVE
B NOT EQUIPPED
MEMORY MEMORY MEMORY SPARE
VOLUME SPARE AFTER PACKING
65535 KB 32405 KB 32405 KB
BUAR1 3082 KB BUAR2 2401 KB
INTER LIM SIGNAL PACKET LENGTH CAPABILITY
BPOS CAPABILITY
002-0-00 90
002-1-00 90

DEVICE BOARDS
NUMBER OF
BPOS BOARDID INDIVIDUALS SERVICE STATE
002-0-00 36 32 ACTIVE
002-0-10 102 32 ACTIVE
002-0-20 36 32 PASSIVE
002-0-30 57 32 PASSIVE
002-0-40 87 16 ACTIVE
002-0-42 87 16 ACTIVE
002-0-50 87 16 ACTIVE
002-0-52 87 16 ACTIVE
002-0-60 106 16 ACTIVE
002-0-62 30 6 ACTIVE
002-0-63 NOT EQUIPPED
002-0-70 42 32 ACTIVE
002-1-00 36 32 ACTIVE
002-1-10 102 32 ACTIVE
002-1-20 57 32 ACTIVE
002-1-30 87 16 ACTIVE
002-1-32 87 16 ACTIVE
002-1-40 87 16 ACTIVE
002-1-42 87 16 ACTIVE
002-1-50 87 16 ACTIVE
002-1-52 87 16 ACTIVE
002-1-60 87 16 ACTIVE
002-1-62 77 16 ACTIVE
002-1-70 77 16 ACTIVE
002-1-72 85 12 ACTIVE
002-2-00 NOT EQUIPPED
002-2-01 NOT EQUIPPED
002-2-02 NOT EQUIPPED
002-2-03 NOT EQUIPPED
002-2-10 102 32 ACTIVE
002-2-20 36 32 PASSIVE
002-2-30 57 32 PASSIVE
002-2-40 87 16 ACTIVE
002-2-42 87 16 ACTIVE
002-2-50 87 16 ACTIVE
002-2-52 87 16 ACTIVE
002-2-60 87 16 ACTIVE
002-2-62 96 1 ACTIVE
002-2-63 30 6 ACTIVE
002-2-70 NOT EQUIPPED
002-2-71 NOT EQUIPPED
002-2-72 77 16 ACTIVE
002-3-00 NOT EQUIPPED
002-3-01 NOT EQUIPPED
002-3-02 NOT EQUIPPED
002-3-03 NOT EQUIPPED
002-3-10 102 32 ACTIVE
002-3-20 87 16 ACTIVE
002-3-22 87 16 ACTIVE
002-3-30 87 16 ACTIVE
002-3-32 87 16 ACTIVE
002-3-40 87 16 ACTIVE
002-3-42 87 16 PASSIVE
002-3-50 87 16 PASSIVE
002-3-52 58 8 ACTIVE
002-3-53 NOT EQUIPPED
002-3-60 87 16 PASSIVE
002-3-62 77 16 ACTIVE
002-3-70 NOT EQUIPPED
002-3-71 NOT EQUIPPED
002-3-72 77 16 ACTIVE


END
<CNBIP:BPOS=2-1-70;

DEVICE BOARD REVISION INFORMATION
DATE: 11OCT05 TIME: 17:27:12

BPOS BOARD/BRDID PRODUCT NUMBER REVISION STATUS ADD
/IND

002-1-70 ELU28 ROF1375334/3 R2A

END
<
WHAT CAN I DO TO ASIGN 32 INDIVIDUALS AT THIS OR ODER ELU28

 

[mundus]

Hi' you have to use CNBOI:BPOS=2-1-70,BRDID=77,NUMIND=32;
but only when you assigned a new board and there is a empty 32 position.

 

[whosrdaddy]

2-1-70 is a no go since 2-1-72 slot is occupied, try to move the 2-1-72 board or move the 2-2-72 board to 2-2-70

-----------------------------------------------------
What You See Is What You Get
Never underestimate tha powah of tha google!

 

[mundus]

Hi' again, the best will be if you have a new ELU 28/3 an assigned this to a empty 32 postion ( ie. 2-2-00 ) with the CNBOI command, if you don't have a new ELU 28/3 then you can assigned this whith the CNBOI to 2-2-00, and then move the extension from 2-1-70 to 2-2-00 with the command KSEXCIR= ,EQU=2-2-00-x; and then just move the ELU32/3 card from 2-1-70 to 2-2-00.

 

[7511066504]

HI,
THANKS A,LOT
I DON,T HAVE A NEW ELU BUT I THINK THAT THERE IS TWO OPORTUNITIES
1. TO MOVE ELU28 FROM 2-3-72 TO 2-3-70 AND ASIGN 32 INDIVIDUALS AND THEN TO MOVE EXTENTIONS
2. TO MOVE VSU BOARD FROM 2-1-72, BUT WHERE AND THAT WHAT IS ASIGNED ON IT WILL IT WORK IN A NEW PLASE OR IT,S NESESERY TO PROGRAM IT AGAIN
EXCUSE MY ENGLISH, I DON,T HAVE ANY DICTIONARI AROUND

 

[7511066504]

HI AGAIN
I,VE MADE JUST LIKE MUNDUS SAIS
<CNBOI:BPOS=2-2-00,BRDID=77,NUMIND=32;
CNBOI:BPOS=2-2-00,BRDID=77,NUMIND=32;
SURE? (YES/NO)
<Y;
EXECUTED
<KSEXIIR=7733,EQU=2-2-00-08,CAT=1,ITYPE=20,ACCTYP=1;
EXECUTED
<ITNUIIR=7099,EQU=2-2-00-08,CAT=0; ;
EXECUTED

<SYEDP:BPOS=2-2-00;
SYSTEM EQUIPMENT DATA
EQU BOARDID TYPE DIR ROU/TRU
002-2-00-08 77 KL1 7733
002-2-00-24 77 KL1 7733
END
<SYEDP:BPOS=2-2-72;
SYSTEM EQUIPMENT DATA
EQU BOARDID TYPE DIR ROU/TRU
002-2-72-00 77 KL1 7703
002-2-72-01 77 KL1 7769
002-2-72-02 77 KL1 7050
002-2-72-03 77 KL1 10325
002-2-72-04 77 KL1 7820
002-2-72-05 77 KL1 7054
002-2-72-06 77 KL1 7080
002-2-72-07 77 KL1 7619
END
<KSEXCIR=7703,EQU=2-2-00-00;
EXECUTED

<KSEXCIR=7769,EQU=2-2-00-01;
EXECUTED

<KSEXCIR=7050,EQU=2-2-00-02;
WAIT
EXECUTED

<KSEXCIR=10325,EQU=2-2-00-03;
EXECUTED

<KSEXCIR=7820,EQU=2-2-00-04;
EXECUTED

<KSEXCIR=7054,EQU=2-2-00-05;
EXECUTED

<KSEXCIR=7080,EQU=2-2-00-06;
EXECUTED

<KSEXCIR=7619,EQU=2-2-00-07;
EXECUTED

<CNBOE:BPOS=2-2-72;
EXECUTED
<SYEDP:BPOS=2-2-00;
SYSTEM EQUIPMENT DATA
EQU BOARDID TYPE DIR ROU/TRU
002-2-00-00 77 KL1 7703
002-2-00-01 77 KL1 7769
002-2-00-02 77 KL1 7050
002-2-00-03 77 KL1 10325
002-2-00-04 77 KL1 7820
002-2-00-05 77 KL1 7054
002-2-00-06 77 KL1 7080
002-2-00-07 77 KL1 7619
002-2-00-08 77 KL1 7733
002-2-00-24 77 KL1 7733
END
<CNHUI:LIM=2;
ORDERED

SPONTANEOUS PRINTOUT

CONFIGURATION HARDWARE UPDATE
LIM 002 NO NEW BOARD FOUND
END

SPONTANEOUS PRINTOUT

CONFIGURATION HARDWARE UPDATE EXECUTED

NOW THERE IS ANOTHER PROBLEM - I VE CONECT NTBA TO DTS PORT ON PBX AND THERE IS NO SIGNAL AT THE BOTH OF THE B-CHANELS
MAYBE THE NT IS NOT OK. I,LL TRY TO FIND ANOTHER ONE.
ALL THE BEST!!!!

 

[whosrdaddy]

dual extension is there to provide S0 EXTENSION, not ISDN TRUNKS, in your case you'll need a TLU79

-----------------------------------------------------
What You See Is What You Get
Never underestimate tha powah of tha google!

 

[7511066504]

HI WHOSRDADDY,
I WANT TO CONECT ONE DBC AND ONE ISDN MODEM AT DTS PORT, WHY SHOULD I USE TLU79, I ANT TO MAKE AN EXTERNAL CONECTIONS VIA ISDN MODEM
I,LL MAKE ENITYNG BETTER IF YOU TELL ME HOW!!
RGDS