How do I verify total number of digital and analog sets in PBX

[vietharry]

Hi All,

How do I verify the total number of digital and analog sets on Opt 61c PBX, just total number for each type?

Thanks

 

[bigindian65]

in use or what?

go to ld 22 REQ:SLT

Mato' Was'aka

 

[bignose21]

would say the easiest way is really to LD 20 prt tnb, capture to a file then open the capture file with mv.xls from pepedog.com.

This will excel all you trunks,sets,tone detectors,etc (anything with a TN). Its then very easy to copy and paste this off to another excel speadsheet with a sheet for your digital and a sheet for you analogues (you get the idea).

This will not only give the the Number of sets but every setting against them making it very easy for you to quickly find sets by searching for DN's and then you can confirm keys, classes of service and anyother features assign or not assigned to a set.

 

[vietharry]

Hi all,
Thank you for all your help, but I only want the total number of analog sets and total number of digital sets separate.(no detail needed)
Please help...
Thanks,

 

[bignose21]

like big indian says ld 22 slt

 

[vietharry]

But this only show the total Tns for digital and analog together
I need to have the total count separate


REQ slt
TNS 2000 LEFT 1240 USED 760
ACDN 24000 LEFT 23954 USED 46
AST 700 LEFT 700 USED 0
DCH 255 LEFT 251 USED 4
AML 16 LEFT 15 USED 1
MUS CON 10 LEFT 10 USED 0
ACD AGENTS 40 LEFT 40 USED 0
INTERNET TELEPHONES 0 LEFT 0 USED 0
WIRELESS VISITORS 0 LEFT 0 USED 0

Pleae help

Thanks

 

[bigindian65]

go to ld 11
look above REQ

there you go....

Mato' Was'aka

 

[bigindian65]

slt seperates analog fron dgtl?? what rls u run'in? did u miss it in the prt???

Mato' Was'aka

 

[bignose21]

was that all of it?

Other than that can you LD 81
Req lst
cust 0
feat type
type 500

Not on a switch at the moment so can confirm this works copy and paste to excel, use text to Column and there's your count do same for other types.

 

[vietharry]

rls 25.40B

 

[strmwalker]

you can go to ld 117 inv gen cards wait until its done
then di inv prt cards.then go to ld 20 and stat your
tns and see what is programmed and whats not its a
little work but its what it is.

no problems only solutions

strmwalker

 

[bigindian65]

SLT has the info he needs, no need to make it any harder than it needs to be, where's ACE when I need him. lol!

Mato' Was'aka

 

[hhallett]

vietharry (TechnicalUser) 6 Aug 08 15:33
But this only show the total Tns for digital and analog together. I need to have the total count separate

REQ slt
TNS 2000 LEFT 1240 USED 760
ACDN 24000 LEFT 23954 USED 46
AST 700 LEFT 700 USED 0
DCH 255 LEFT 251 USED 4
AML 16 LEFT 15 USED 1
MUS CON 10 LEFT 10 USED 0
ACD AGENTS 40 LEFT 40 USED 0
INTERNET TELEPHONES 0 LEFT 0 USED 0
WIRELESS VISITORS 0 LEFT 0 USED 0

You're right. This just tells you that you have 2000 total TNs of which 760 are used. It doesn't split them up for you. Which is odd since I thought that release did split digital and analog when printing the System LimiTs.


Anyway, since all you want is separate counts of the digital and analog sets you have currently programmed give this a try.

Go to LD 81.

REQ CNT
CUST 0 (Or the appropriate #)
DATE (hit enter)
PAGE (hit enter)
DES (hit enter)
FEAT 2000 (for digital sets)
FEAT DTN (for the average analog set)
FEAT DIP (in case you have any analogs set up as Dial-Pulse)
FEAT MNL (in case you have any analogs set up as Ring Downs)
FEAT SL1 (Just in case your system is old enough)
FEAT (hit enter)

You'll get a display that looks similar to this:

FEAT CUST TOTAL SL1 500 2500 2000
DIP 00 CNT 0 0 0 0 0
DTN 00 CNT 672 0 0 672 0
MNL 00 CNT 11 0 11 0 0
SL1 00 CNT 16 16 0 0 0
2000 00 CNT 195 0 0 0 195

DIP, MNL and DTN are analogs so you can just add them up.

Regards,
Harry
"The legitimate powers of government extend to such acts only as are injurious to others. But it does me no injury for my neighbour to say there are twenty gods, or no god. It neither picks my pocket nor breaks my leg." --Thomas Jefferson

 

[hhallett]

Ooops. *smacks forhead*

Rls 25.40 ... D'uh!

Nevermind about the SL1.

Regards,
Harry
"The legitimate powers of government extend to such acts only as are injurious to others. But it does me no injury for my neighbour to say there are twenty gods, or no god. It neither picks my pocket nor breaks my leg." --Thomas Jefferson

 

[bigindian65]

what comes up above ld 10 for analogue and ld 11 for digital when you go into those overlays? Same thing??

Mato' Was'aka

 

[vietharry]

I get the total ports count 760 on ld 10 and 11
same thing

 

[bigindian65]

that sucks. Sorry. could stat the loops and leave off the unit i e, stat 4 0 0, stat 4 0 1 and see what is/ is not uneq

tedious, but works.

Mato' Was'aka

 

[hawks]

I think with the software you have hhallett has the best solution for you in LD 81.

 

[tnphoneman]

In ld 81 at the feat prompt just type sets and return through. This will give you all sets in the count.

500 and 2500 will be analog
Others will be listed as 2000 or 3900 etc.

Signature===========================================
Artificial Intelligence Is No Match for Natural Stupidity.

The latest survey shows that 3 out of 4 people make up 75% of the population.

The original point and click interface was a Smith & Wesson.

Red meat is not bad for you, it is the green fuzzy meat that is bad.

 

[MagnaRGP]

tnphoneman has it nailed.

ld 81
REQ lst
CUST 0
DATE (hit enter)
PAGE (hit enter)
DES (hit enter)
FEAT sets

enter on home.

Add up 500 and 2500 to equal the analogs in use and add up 2000 and 3900s for digital. subtract the number of mail ports (CP and Mermail) for an accurate count of digital sets in use.