Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

How do I send number besides DN over tie 3

Status
Not open for further replies.

3cross

Technical User
Aug 28, 2007
20
US
I can't get the CLID table to send a specific #. I can get it to add the area and office code I need but it always uses the phone DN. These are going over a tie then out a PRI at the other location.We are trying to use ext. 6133 on the outbound ID instead of the DN. Everything works but we can't get the DN replaced.

=========

ENTRY 1
HNTN aaa
ESA_HLCL
ESA_INHN NO
ESA_APDN NO
HLCL 6133
DIDN NO
HLOC aaaooo
LSC
CLASS_FMT DN

========

FEAT :CRID
FEAT :NCID
PROGRESS: CALL IS NOT END TO END ISDN
CALLING #:aaaoooxxx NUM PLAN: PRIVATE/RESERVED (LOC)
CALLED #:10131aaaoooxxxNUM PLAN: PRIVATE/NETWORK SPECIFIC (SPN)


 
This is one of the tables that explains what each prompt is:

[tt]
REQ: CHG
TYPE: NET
TYPE NET_DATA
CUST 0
OPT
AC2
FNP
CLID YES < CLID Gate Opener
SIZE
INTL
ENTRY 0 < CLID Table to be modified/created
HNTN 972 < All Calls - NPA (Area Code)
ESA_HLCL 362 < Emergency Calls - NXX (Local Exchange)
ESA_INHN YES/NO < Emergency Calls - Include NPA on CLID
ESA_APDN YES/NO < Emergency Calls - Include DN on CLID
HLCL 362 < Normal Calls - NXX (Local Exchange)
DIDN YES/NO < Normal Calls - Include DN on CLID
HLOC 442 < UDP Calls - Home Location Code
LSC 2 < CDP Call - Local Steering Code (if used)
[/tt]

[&copy;] GHTROUT.com [&hArr;] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators
 
You know, I think you might need to change the route from TIE to DID to get the CLID to send - I'm not certain.

TIE and DID are somewhat interchangeable - worth investigating in your scenario.

[&copy;] GHTROUT.com [&hArr;] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators
 
Not sure if I am answering the question but I'll give it a shot.

Create the scr key 0 XXXX D

— When the character "D" is entered, the
system searches the DN keys from key 0
and up, to find a DN key with a CLID table
entry. The CLID associated with the found
DN key is used.

This presumes your have scr 6133 on one of the buttons
 
I read the downloaded info and followed the first example. This was routing the calls out over a branch using NRS and in the SPN I needed to set CLTP to NATL. It was at none and the calls were treated as UDP or CDP calls and always used the ext. #.

Using element manager for making changes to the ESN is a lot easier since it shows all available prompts.

Thanks for the downloads and help Greg.
 
Yes, that's the best documentation I've seen for a while. Great job!



[&copy;] GHTROUT.com [&hArr;] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators
 
As such, the file has been updated.

[&copy;] GHTROUT.com [&hArr;] A Variety of Free Resources for Nortel Meridian/CS1000 System Administrators
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top