ZPLprogrammer
Programmer
Can't seem to get the cutter to move to desired position. Can set printer config. manually but want to include the tear-off as part of the label format. Trying the TA but not having any success. Any ideas?
Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
How do I code Tear-off in ZPL II?
- Thread starter ZPLprogrammer
- Start date
- Status
It the ~TA command isn't working for you, do you perhaps have the ^XB command in force that suppresses backfeed?
If so try removing ^XB and see if your problems go away.
Jim Asman
If so try removing ^XB and see if your problems go away.
Jim Asman
- Thread starter
- #3
ZPLprogrammer
Programmer
No, no XB present. Here's the code I'm trying to no avail. Note the TA+56.
~CC¬
¬XA¬JMA¬FS¬XZ
¬XA¬SS,,,0870¬FS¬XZ
¬XA¬MTT¬FS¬XZ
¬XA¬MNW¬FS¬XZ
¬XA¬MMC¬FS¬XZ
¬XA¬TA+56¬FS¬XZ
¬XA¬MD+19¬FS¬XZ
¬XA¬LT-64¬FS¬XZ
¬XA¬PRB¬FS¬XZ
¬XA¬IDR:*.LGO¬XZ
¬XA¬IDR:*.*¬XZ
¬XA¬MCY¬XZ
¬XA¬LH0000,0000¬FS¬PON¬FS
¬FO0021,0411¬A0N,0041,0051¬FDSize :¬FS
¬FO0033,0531¬A0N,0028,0030¬FDDpt/Cl¬FS
¬FO0318,0531¬A0N,0028,0030¬FDSeason¬FS
¬ISLB,N¬FS¬XZ¬XA¬MCY¬XZ¬XA¬ILLB¬FS
¬FO0000,0000¬AAN,0000,0000¬FD ¬FS
¬FO0057,0270¬BY4,2,100¬BUN,0090,Y,N,Y¬FD007311040351¬FS
¬FO0021,0195¬A0N,0041,0051¬FDDB-142 SMART XX¬FS
¬FO0018,0234¬A0N,0041,0051¬FDBLUE CHECK PATT¬FS
¬FO0138,0411¬A0N,0041,0051¬FD16.5 34¬FS
¬FO0282,0792¬A0N,0057,0068¬FD29.99¬FS
¬FO0039,0654¬BY2,2,100¬BCN,0090,N,N¬FD900780100005950¬FS
¬FO0045,0495¬A0N,0028,0030¬FD0781¬FS
¬FO0351,0492¬A0N,0028,0030¬FDE3¬FS
¬PQ0001,0000,0000,N¬FS¬MCN¬XZ
~CC¬
¬XA¬JMA¬FS¬XZ
¬XA¬SS,,,0870¬FS¬XZ
¬XA¬MTT¬FS¬XZ
¬XA¬MNW¬FS¬XZ
¬XA¬MMC¬FS¬XZ
¬XA¬TA+56¬FS¬XZ
¬XA¬MD+19¬FS¬XZ
¬XA¬LT-64¬FS¬XZ
¬XA¬PRB¬FS¬XZ
¬XA¬IDR:*.LGO¬XZ
¬XA¬IDR:*.*¬XZ
¬XA¬MCY¬XZ
¬XA¬LH0000,0000¬FS¬PON¬FS
¬FO0021,0411¬A0N,0041,0051¬FDSize :¬FS
¬FO0033,0531¬A0N,0028,0030¬FDDpt/Cl¬FS
¬FO0318,0531¬A0N,0028,0030¬FDSeason¬FS
¬ISLB,N¬FS¬XZ¬XA¬MCY¬XZ¬XA¬ILLB¬FS
¬FO0000,0000¬AAN,0000,0000¬FD ¬FS
¬FO0057,0270¬BY4,2,100¬BUN,0090,Y,N,Y¬FD007311040351¬FS
¬FO0021,0195¬A0N,0041,0051¬FDDB-142 SMART XX¬FS
¬FO0018,0234¬A0N,0041,0051¬FDBLUE CHECK PATT¬FS
¬FO0138,0411¬A0N,0041,0051¬FD16.5 34¬FS
¬FO0282,0792¬A0N,0057,0068¬FD29.99¬FS
¬FO0039,0654¬BY2,2,100¬BCN,0090,N,N¬FD900780100005950¬FS
¬FO0045,0495¬A0N,0028,0030¬FD0781¬FS
¬FO0351,0492¬A0N,0028,0030¬FDE3¬FS
¬PQ0001,0000,0000,N¬FS¬MCN¬XZ
I'm not sure what the punctuation character is before each command as displayed here. Make sure you are using ~TA with a tilde in the real file.
The only thing that comes to mind is that you may have to pad the distance with a 0 to make it 3 digits, So try...
~TA+056
or
~TA056
Maybe it doesn't like the "+"
Jim Asman
The only thing that comes to mind is that you may have to pad the distance with a 0 to make it 3 digits, So try...
~TA+056
or
~TA056
Maybe it doesn't like the "+"
Jim Asman
I just tried ~TA056 on my printer and it advanced the label about 1/4 inch.
Jim Asman
Jim Asman
- Thread starter
- #6
ZPLprogrammer
Programmer
For some reason, our label software (TL Ashford) replaces the carat with that other character. I'd actually discovered that I needed a tilde for the TA prior to your reply.
But it was the 3 digits that did the trick. I just assumed that it was a max of 3 digits, not a requirement. I saw that other commands worked that way. But as long as it works, I'm happy.
The resolution was:
¬XA~TA056¬FS¬XZ
Thanks for your help. You're a genuis!
But it was the 3 digits that did the trick. I just assumed that it was a max of 3 digits, not a requirement. I saw that other commands worked that way. But as long as it works, I'm happy.
The resolution was:
¬XA~TA056¬FS¬XZ
Thanks for your help. You're a genuis!
- Status
Similar threads