How can I open account for per user LDK-300

[teomcam]

Is there any way to open account to the people (90 people)? Whichever handset they use, they have to access CO Lines, even from restricted handsets. How I can do that?

 

[doktor]

The extension numbers exist already, but can be changed in PGM105.
Access to CO lines are set in the station COS (Class of Service) in PGM117.

The account codes are found in PGM227 of the ipLDK systems.

Read more from here, if you really start from scratch:

http://www.lg-nortel.es/lgnortel/areatecnica/manualesldkipldk/index.html

Check out the programming manual of the ipLDK-100.

///doktor

 

[teomcam]

Hi doktor,

Ive read that section already but didnt get much. If I wanna open an account for person A and person B what I have to do?

Person A station number 100
Person B station number 105

These 2 guys can access CO Lines from their own stations. If they wanna access from other stations for example station 120 or 124 which they restricted, what I have to do?

 

[morenot]

You can use Walking Cos Feature

With this Code you can dialing from any set
This Code is assigned to people not to phone.

 

[Chamvari]

Can walking COS be billed by the smdr or the extension will be billed.

Dial Tone shoul be There

 

[teomcam]

Sounds great but how can I configure walking COS. I could not find any similar section under COS.

 

[morenot]

Check this:

2.5.6 Walking COS
Description
This feature allows temporarily override of the toll restriction and allows toll call from previously toll restricted
phones. The authorization code (refer to Ref. A) can be used as a verified account code for SMDR (refer to Ref.
B).
Operation
To activate Walking COS from a DKTU, perform the following Steps:
1. Press the [TRANS/PGM] button.
2. Dial 2 3; the confirmation tone should be heard
3. Enter the authorization code; the intercom dial tone should be heard and the used extension COS (Ref.
C) is temporarily changed.
4. A CO line call can be placed only one time.
To program {Walking COS} on a flexible button:
1. Press the [TRANS/PGM] button.
2. Press the applicable FLEX button.
3. Press the [TRANS/PGM] button.
4. Dial 2 3.
5. Press the [HOLD/SAVE] button to accept changes.
Condition
?? Can be used on DKTUs and SLTs.
?? Available on a per-use basis only. While activating walking COS, hanging-up or pressing the [TRANS/PGM]
button to hold the call and seize another line, the original programmed Station COS will be used.
?? When a wrong number is dialed, press the [FLASH] button to dial again without changing to an idle CO line.
?? The fee for a call with Walking COS will be charged according to the Station authorization code, not the actual
Station.
?? When a User tries to use Walking COS at a station set to COS 7 with temporary COS, the call will follow the
original COS of the Station.
Reference
A. Authorization: 2.5.2
B. SMDR: 2.12
C. COS: 2.5.4
Admin Programming
1. Authorization Code Table (PGM 227)

To set up Authorization code:
PGM 227

For ipldk 60(max. 48 extensions), you must begin use index 49,50,51...
because index 1 to 48 is for authorization codes pairing with extensions.

For ipldk 300, I don´t know how max extensions it have,
but should be similar, you should begin with:
PGM 227: index: max exts + 1

JLMT//