Hooking up a Mitel 3300 to a Nortel 81c

[gregdeike]

We are having problems hooking up a Mitel 3300 IP box to our Nortel 81c. I am set up as the user and the mitel is set up as the CO. I have listed my information below. Any help would be great thanks.

>LD 22
PT2000

REQ PRT
TYPE ADAN DCH 43

ADAN DCH 43
CTYP MSDL
GRP 1
DNUM 13
PORT 2
DES 3COMVOIPDCH
USR PRI
DCHL 43
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC D100
SIDE USR
CNEG 1
RLS ID **
RCAP ND2
MBGA NO
OVLR NO
OVLS NO
T200 3
T203 10
N200 3
N201 260
K 7

REQ PRT
TYPE CEQU

CEQU
MPED 8D
TERM
REMO
TERD
REMD
TERQ
REMQ
SUPL 004 020 028 036
044 052 060 N140
V160
SUPC
SUPF
XCT 000 016 032 048
TDS * 000 * 016 * 032 * 048
CONF * 001 * 017 * 033 * 049
MFSD * 000 * 016 * 032 * 048

DLOP NUM DCH FRM TMDI LCMT YALM TRSH
PRI 002 00 ESF NO B8S FDL 00
003 24 ESF NO B8S FDL 00
010 24 ESF NO B8S FDL 00
011 12 ESF NO B8S FDL 00
026 00 ESF NO B8S FDL 00
027 24 ESF NO B8S FDL 00
034 24 ESF NO B8S FDL 00
035 24 ESF NO B8S FDL 00
043 24 ESF NO B8S FDL 00
050 24 ESF NO B8S FDL 00
DTIC 012 013 014 015
MISP
EXT0 3PE
CNI 009 000 000
CNI 009 001 001
EXT1 3PE
CNI 009 000 000
CNI 009 001 001
MCFN 256 MB

REQ PRT
TYPE RDB

SCH0111

TYPE
OVL000
>LD 21
PT1000

REQ: PRT
TYPE: RDB
CUST 0
ROUT 43

TYPE RDB
CUST 00
ROUT 43
DES 3COMVOIP
TKTP TIE
NPID_TBL_NUM 0
ESN NO
CNVT NO
SAT NO
RCLS EXT
VTRK NO
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC D100
SBN NO
PNI 00000
NCNA YES
NCRD NO
CHTY BCH
CTYP UKWN
INAC NO
ISAR NO
CPUB OFF
DAPC NO
BCOT 0
DSEL VOD
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 7043
TCPP NO
PII NO
TARG 01
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
ANTK
SIGO STD
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3
NBS 2048
NBL 4096


PAGE 002


IENB 5
TFD 0
VSS 0
VGD 6
DRNG NO
CDR NO
VRAT NO
MUS NO
RACD NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TDET NO
TTBL 0
ATAN NO
PLEV 2
ALRM NO
ART 0
SGRP 0
AACR NO

 

[hawks]

Does the Mitel emulate D100 or NI2?

 

[johnpoole]

hawks right ni2 will come closer to working, what are your symptoms? i would loop the pri in both directions, the pri should come up, d will est the rls wronge mode.. post the mitel config, this side looks right, i never leave targ set to 1.. another big burn is the dch, make sure you dis msdl x all and enl msdl x fdl for any change on the d, other wise the software says one thing the download on the card is still on last download config..

john poole
bellsouth business
columbia,sc

 

[gregdeike]

The Mitel is set up as D100 also. The Mitel programming looks like there is no slot for a DCH on it. I beleive this is the key to getting it up and working.

 

[johnpoole]

very true, you can use the same card in the sl1, with out a dch, you'll need to build with isdn=no and have a t1 with no lamps or names ... not a good thing

john poole
bellsouth business
columbia,sc