Hipath 4000 v6 + OpenStage 40 SIP (Need Help) 1

[buang]

hallo everyone, anybody help me?

here is the case.
Equipment :
- Siemens Hipath 4000 v6 PBX (COM server + LTU1) with installed module LTUCA,TMANI,SLMO2,STMI4
- Siemens OpenStage 40 SIP
- ComWin

i had succesfully to configure LTUCA, TMANI, SLMO module and create two extension and it works good (ext.100 and ext.101). the problem is i must configure STMI4 module and create a extension on OpenStage 40 SIP so it can use to dialing other extension.
- STMI4 had successfully installed on LTU1
- Success creating a extension for OpenStage 40 SIP (ext. 200) but when i try to dial ext.100 there is a message "unable to select an outgoing line" on the display. it also cant be dialed from ext.100. (cant outgoing and incoming)

its a flowchart that i had configured
- BCSU : to ensure the STMI4 module is registered and ready (Done)
- SBCSU : to create a extension for OpenStage 40 SIP (Done)
- SIPCO
- CGWB

Anybody help me, need flowchart to configure it. Thanks a lot




DIS-BCSU:TBL;
H500: AMO BCSU STARTED

LTG 1 LTU 1 SRCGRP 1 ALARMNO-LTU 0
-----+-----------+--------+---+-+-+---+-+------------+------------+------------
| | | |S|H|AL-| | | |
| ASSIGNED | MODULE |FCT|E|W|ARM| | INSERTED | HW- | MODULE
PEN | MODULE | TYPE |ID |C|Y|NO | | MODULE |STATE INFO | STATUS
-----+-----------+--------+---+-+-+---+-+------------+------------+------------
1 | Q2324-X500 STMI4 1 * A 0| | Q2324-X500 | 1 -11 - | READY
+--------------------------------+-+------------+------------+------------
| IP ADDRESS : 172. 22. 0. 98 B-CHANNELS : 60 BCHLCNT : 60
| IP MODE : IPV4 DHCP V4 : NO DHCP V6 : NO
| BLOCK NO : 1 PRERESERVED LINES ASSIGNED : NO
| 1. FUNCT : HG3570 1 LINES B-CHANNELS : 30 BCHLCNT : 30
| 2. FUNCT : HG3550 1 LINES B-CHANNELS : 20 BCHLCNT : 20
| 3. FUNCT : HG3530 240 LINES B-CHANNELS : 10 BCHLCNT : 10
+--------------------------------+-+------------+------------+------------
7 | Q2266-X LTUCA 0| | Q2266-X | 1 -15 - | READY
8 | Q2327-X100 TMANI A 0| | Q2327-X100 | 1 -11 - | READY
13 | Q2168-X SLMO24 1 A 0| | Q2168-X | 1 -11 - | READY +----+----+---------------------------+-+------------+------------+--------+
| NO SECURITY STATUS AVAILABLE, SINCE FEATURE SPE IS NOT ACTIVATED|
+---------+----------------------------------------------------------------+
AMO-BCSU -111 BOARD CONFIGURATION, SWITCHING UNIT
DISPLAY COMPLETED;

<dis-sipco;
DIS-SIPCO;
H500: AMO SIPCO STARTED
CENTRAL IP ADDRESSES ( LSNET ) :
-------------------------------------------------------------------
NETADDR ( NET ADDRESS OF THE SYSTEM LAN SEGMENT ) : 172.22.0.0
NETMASK ( NET MASK OF THE SYSTEM LAN SEGMENT ) : 255.255.255.0
IPMODE ( IPMODE ) : IPV4
DEFRT ( ADDRESS OF THE DEFAULT ROUTER ) : 172.22.0.254
CCAADDR ( ADDRESS OF THE CC-A PROCESSOR ) : 172.22.0.93
CCBADDR ( ADDRESS OF THE CC-B PROCESSOR ) : N/A
SURVNET ( NET ADDRESS OF THE SURVIVABILITY NET ) : 0.0.0.0
DHCPV4 ( DHCPV4 ) : N
DHCPV6 ( DHCPV6 ) : N

<dis-cgwb
LTU = ;
DIS-CGWB:;
H500: AMO CGWB STARTED
------------------------------------------------------------------------------
| CGW BOARD DATA |
------------------------------------------------------------------------------
| HG3530 HG3550 HG3570 |
------------------------------------------------------------------------------
| LTU = 1 SLOT = 1 SMODE = NORMAL POOLNO: 0 |
------------------------------------------------------------------------------

GLOBAL DATA AND ETHERNET INTERFACE DATA - CONFIGURABLE VALUES:
--------------------------------------------------------------
IPADR = 172.22 .0 .98 TCPP = 4060 (4060)
NETMASK = 255.255.255.0 VLAN = NO (NO)
DEFRT = 0 .0 .0 .0 (0.0.0.0 = NOT CONFIGURED)
BITRATE = 100MBFD (AUTONEG) VLANID = 0 (0)
PATTERN = 213 (213)
TRPRSIP = 0 (0)
TRPRSIPQ = 0 (0)
TRPRH323 = 8 (0)
TPRH323A = 0 (0)
TLSP = 4061 (4061)

GLOBAL DATA - CONSTANT VALUES:
------------------------------
AMO INTERFACE VERSION: 0 OPMODE: 1 DATA_VALID: YES

DNSIPADR = 0.0.0.0
DNSIPADR2 = 0.0.0.0

SIP TRUNKING DATA FOR SSA
---------------------------
SIPREG = NO (NO)
REGIP1 = 0.0.0.0 (0.0.0.0)
PORTTCP1 = 5060 (5060)
PORTTLS1 = 5061 (5061)
REGIP2 = 0.0.0.0 (0.0.0.0)
PORTTCP2 = 5060 (5060)
PORTTLS2 = 5061 (5061)
REGTIME = 120 (120)

 

[sbcsu]

add in the default router in CGWB
CHA-CGWB

 

[buang]

[tt][/tt]CGWB : The default route had created as 172.22.0.98
i try to restarting module with RES-BSSU. Doesnt work. May be i missed a parameter that i must configured?

Buang

 

[hipath0514]

Hello,


Your IP Address must not be the same as your Default route.


--------------------------------------------------------------
IPADR = 172.22 .0 .98 TCPP = 4060 (4060)
NETMASK = 255.255.255.0 VLAN = NO (NO)
DEFRT = 0 .0 .0 .0 (0.0.0.0 = NOT CONFIGURED)
BITRATE = 100MBFD (AUTONEG) VLANID = 0 (0)
PATTERN = 213 (213)
TRPRSIP = 0 (0)
TRPRSIPQ = 0 (0)
TRPRH323 = 8 (0)
TPRH323A = 0 (0)
TLSP = 4061 (4061)

CGWB : The default route had created as 172.22.0.98
i try to restarting module with RES-BSSU. Doesnt work. May be i missed a parameter that i must configured?



Thanks

Hipath0514

 

[sbcsu]

the default router is 172.22.0.254
so


CHANGE-CGWB:CGW,1,1,GLOBIF,,,213,NO,0,172.22.0.254,,AUTONEG,0,0,60,0,4061,0.0.0.0;
RES-BSSUEN,,1,1;

 

[buang]

I had find a flowchart how to configure the OpenStage 40 SIP.
I must activate SIP subscriber on AMO ADD-BFDAT and then assign it into STMI4 module.
First , I need to delete parameter HG3530, HG3550, HG3570 that was listed in CGWB configuration. (Need Help)
Second, i need to delete STMI4 module that registered on BCSU, i were try to delete this module with AMO DEL-BCSU :IPGW,1,1,1; but there is error message F10 : Module line circuits not deleted. (Need Help)

I was change the default route parameter to 172.22.0.254 and doesnt work. Thanks b4

 

[hipath0514]

you need to configure

BFDAT with SIP functionality

 

[buang]

Here is the last configuration but the phone still doesnt work. may be i missed some configuration?
there is failed to configuring SIP extension and here is the error message :

ADD-SBCSU:199,FPP,SIP,1-1-3-0,S0PP,1,1,1,1,1,1,0,0,N,0,0,,,SBDSS1,Y,Y,0,10,N,
N,,,5,0,,,,"","","",,,,;
H500: AMO SBCSU STARTED
H62: FOR SIP SUBSCRIBERS PARAMETER MBCHL (MULTIPLE BCHANNEL) MUST BE
SET IN AMO-SDAT.
F41: VALUE FOR PARAMETER OPT DOES NOT MATCH THE MODULE OF THE
SPECIFIED PEN
and then i try with different parameters for creating SIP extension and still doesnt work. :-(

ADD-BFDAT:2,HG3570&HG3550&HG3530&SIP,BCHL60&BCHL120,;
CHA-BFDAT:CONT,2,HG3570,,,1;
CHA-BFDAT:CONT,2,HG3550,1,1,;
CHA-BFDAT:CONT,2,HG3530,10,,1;
CHA-BFDAT:CONT,2,SIP,10,,1;
CHA-BFDAT:OK,2,YES;

ADD-BCSU:IPGW,1,1,3,"Q2324-X500",1,0,2,172.22.0.99,1,1,10,,1,0,IPV4,NO,NO;

CHANGE-CGWB:CGW,1,3,GLOBIF,,,213,NO,130,172.22.0.254,4060,AUTONEG,0,0,0,0,4061,0.0.0.0,0.0.0.0;
CHA-CGWB:CGW,1,1,SERVIF,"TRM";
CHA-CGWB:CGW,1,1,ASC,29100,30099,184,104,YES,NO,YES,YES,PRIO1,G711A,NO,30;
CHA-CGWB:CGW,1,1,ASC,,,,,,,,,PRIO2,G729A,NO,20;
CHA-CGWB:CGW,1,1,ASC,,,,,,,,,PRIO3,G723,NO,30;
CHA-CGWB:CGW,1,1,ASC,,,,,,,,,PRIO4,NONE,NO,20;
CHA-CGWB:CGW,1,1,ASC,,,,,,,,,PRIO5,NONE,NO,20;
CHA-CGWB:CGW,1,1,ASC,,,,,,,,,PRIO6,NONE,NO,20;
CHA-CGWB:CGW,1,1,ASC,,,,,,,,,PRIO7,G729AB,YES,20;
CHA-CGWB:CGW,1,1,DSP,60;
CHA-CGWB:CGW,1,1,GKDATA,,1719,"PRIMARYRASMANAGERID",,,1719,"SECONDARYRASMANAGERID",,120;
CHA-CGWB:CGW,1,1,MGNTDATA,,8000,,443;
CHA-CGWB:CGW,1,1,DMCDATA,0;
CHA-CGWB:CGW,1,1,WBMDATA,"HP4K-DEVEL",,ENGR;
CHA-CGWB:CGW,1,1,WBMDATA,"HP4K-SU",,SU;
CHA-CGWB:CGW,1,1,WBMDATA,"HP4K-ADMIN",,ADMIN;
CHA-CGWB:CGW,1,1,WBMDATA,"HP4K-READER",,READONLY;
CHA-CGWB:CGW,1,3,GWDATA,"PRIMARYRASMANAGERID",;
CHA-CGWB:CGW,1,1,H235DATA,NO,NO,"siemensGateway2003",,100,242-191-30-119-188-83-173-161-43-0-70-36-218-74-169-221-78-102-174-170;
CHA-CGWB:CGW,1,3,SIPTRERH,NO,,,;
CHA-CGWB:CGW,1,3,SIPTRSSA,NO,0.0.0.0,5060,5061,120,0.0.0.0,5060,5061;
CHA-CGWB:CGW,1,3,DLSDATA,,10444,NO;
CHA-CGWB:CGW,1,3,JB,40,120,20,4,60,200,2;

ADD-SBCSU:199,OPTI,IP2,1-1-3-0,OPTIIP,1,1,1,11,1,1,1,0,0,N,0,0,,,N,0,0,N,,,Y,0,N,N,N,Y,N,,,,,,,,5,,,,N,NORMAL,Y,ENGLISH,0,,,0,,,,,,,,,G711P,,;

CHA-SDAT:199,ATTRIBUT,MBCHL;

 

[hipath0514]

Hi,

You need to configure your HG card with a SIP function block for the SIP clients.

In order to do this you need to delete all the existing configuration and reconfigure it again.


Thanks

 

[buang]

i'll try to delete all existing configuration and reconfigure it. waiting for my last update. thanks for your advice

 

[buang]

this is my last configuration to activate OpenStage 40 SIP. But there is error message unable to select an outgoing line on the OpenStage display. Im using STMI4 modul

ADD-BFDAT:2,SIP,BCHL60&BCHL120,;
CHA-BFDAT:CONT,2,SIP,10,,1;
CHA-BFDAT:OK,2,YES;
ADD-BCSU:IPGW,1,1,3,"Q2324-X500",1,0,2,,,1,,,,0,IPV4,NO,NO;
ADD-CGWB:1,3,NORMAL,172.22.0.100,255.255.255.0;
CHANGE-CGWB:CGW,1,3,GLOBIF,,,213,NO,0,172.22.0.254,,100MBFD,,,,,4061,0.0.0.0,0.0.0.0;
CHANGE-CGWB:CGW,1,3,SERVIF,"TRM";
CHANGE-CGWB:CGW,1,3,ASC,29100,30099,184,104,YES,NO,YES,YES,PRIO1,G711A,NO,30;
CHANGE-CGWB:CGW,1,3,ASC,,,,,,,,,PRIO2,G729A,NO,20;
CHANGE-CGWB:CGW,1,3,ASC,,,,,,,,,PRIO3,G723,NO,30;
CHANGE-CGWB:CGW,1,3,ASC,,,,,,,,,PRIO4,NONE,NO,20;
CHANGE-CGWB:CGW,1,3,ASC,,,,,,,,,PRIO5,NONE,NO,20;
CHANGE-CGWB:CGW,1,3,ASC,,,,,,,,,PRIO6,NONE,NO,20;
CHANGE-CGWB:CGW,1,3,ASC,,,,,,,,,PRIO7,G729AB,YES,20;
CHANGE-CGWB:CGW,1,3,DSP,60;
CHANGE-CGWB:CGW,1,3,GKDATA,,1719,"PRIMARYRASMANAGERID",,1719, "SECONDARYRASMANAGERID",,120;
CHANGE-CGWB:CGW,1,3,MGNTDATA,,8000,,443;
CHANGE-CGWB:CGW,1,3,DMCDATA,0;
CHANGE-CGWB:CGW,1,3,WBMDATA,"HP4K-DEVEL",,ENGR;
CHANGE-CGWB:CGW,1,3,WBMDATA,"HP4K-SU",,SU;
CHANGE-CGWB:CGW,1,3,WBMDATA,"HP4K-ADMIN",,ADMIN;
CHANGE-CGWB:CGW,1,3,WBMDATA,"HP4K-READER",,READONLY;
CHANGE-CGWB:CGW,1,3,GWDATA,"PRIMARYRASMANAGERID",;
CHANGE-CGWB:CGW,1,3,H235DATA,NO,NO,"siemensGateway2003",,100,242-191-30-119-188-83-173-161-43-0-70-36-218-74-169-221-78-102-174-170;
CHANGE-CGWB:CGW,1,3,SIPTRERH,NO,,,;
CHANGE-CGWB:CGW,1,3,SIPTRSSA,NO,0.0.0.0,5060,5061,120,0.0.0.0,5060,5061;
CHANGE-CGWB:CGW,1,3,DLSDATA,,10444,NO;
CHANGE-CGWB:CGW,1,3,JB,40,120,20,4,60,200,2;
ADD-SBCSU:199,FPP,SIP,1-1-3-0,S0PP,1,1,1,1,1,1,0,0,N,0,0,,,SBDSS1,Y,Y,0,10,N,N,,,5,0,,,172.22.0.93,"","","",,,,;
CHA-SDAT:199,ATTRIBUT,MBCHL;

 

[sbcsu]

it might only be that you have the LCOSV set to 1 in the SBCSU
otherwise it all looks good.
If the phone is registered and up and running you are there

 

[Iamnothere]

Your Oct 22 attempt failed because you used the wrong PEN. When you built this BFDAT entry:
ADD-BFDAT:2,HG3570&HG3550&HG3530&SIP,BCHL60&BCHL120,;

.... the SIP Subscriber PEN was NOT channel 0. You used 1-1-3-0 as your PEN, and that PEN was assigned to the HG3570 functionality on the STMI board. Use DIS-SDSU:ALL,,PEN,PER3,1,1,3; to display the layout of the channels. After the AMO header, and before the actual channel info, you will see a "legend" that defines the channel assignments, such as: channel 0 is assigned to HG3570, channel 1 is assigned to HG3550, channels 2-31 are assigned to HG3530, and channels 32-50 are assigned to SIP (these numbers are just examples). From my example, your SIP subscriber should have been assigned the PEN 1-1-3-32. By the way, you are assigning only 1 B-channel to the HG3570, HG3530, and SIP. This means that only 1 call is allowed. You will not be able to call another HFA phone, since this call would require 2 B-channels. Be careful what you type!!

In your most recent attempt, you have configured BFDAT to allow 10SIP phones, but you allowed only 1 B-channel. See your command: CHA-BFDAT:CONT,2,SIP,10,,1;

In this AMO, parameter LINECNT=10 means that you wish to build 10 SIP Subscribers. The next parameter, UNITS, is skipped when configuring subscribers. The next parameter is BCHLCNT, which you assigned as "1". You will need to re-build the BFDAT to allow at least 10 B-channels to avoid blockage.

Also, a SIP Subscriber needs to use OPTIDX=10, which is a rarely used (for DSS1 devices such as SIP) table in AMO ZAND -> OPTISET -> OPTTABLE. This table 10 is not typically loaded into memory, since it is not frequently used.. If you are building the first SIP phone that has ever been configured in this switch, then you will probably need to manually load this OPTIDX table 10. Usually the symptom is that a call attempted from the new SIP phone results in a "high and dry", which means NOTHING HAPPENS, DEAD SILENCE. The command is: CHA-ZAND:OPTLOAD;
This command loads all assigned OPTIDX tables into memory. This action usually resolves the DEAD SILENCE on SIP Subscriber calls.

Good luck.

 

[buang]

Here is my last configuration update. I try to applying as you suggested. Is this correct? After this configuration has created ,there is same problem as before. An error message on display "unable to select an outgoing line".

Thanks in advance

ADD-BFDAT:2,HG3570&HG3550&HG3530&SIP,BCHL60&BCHL120,;
CHA-BFDAT:CONT,2,HG3570,,,20;
CHA-BFDAT:CONT,2,HG3550,1,1,;
CHA-BFDAT:CONT,2,HG3530,10,,10;
CHA-BFDAT:CONT,2,SIP,10,,10;
CHA-BFDAT:OK,2,YES;
ADD-BCSU:IPGW,1,1,3,"Q2324-X500",1,0,2,172.22.0.100,10,10,10,,20,0,IPV4,NO,NO;
ADD-CGWB:1,3,NORMAL,172.22.0.100,255.255.255.0;
CHANGE-CGWB:CGW,1,3,GLOBIF,,,255,NO,0,172.22.0.254,4060,100MBFD,0,0,0,0,4061,0.0.0.0,0.0.0.0;
CHANGE-CGWB:CGW,1,3,SERVIF,"TRM";
CHANGE-CGWB:CGW,1,3,ASC,29100,30100,184,104,YES,NO,YES,YES,PRIO1,G711A,NO,30;
CHANGE-CGWB:CGW,1,3,ASC,,,,,,,,,PRIO2,G729A,NO,20;
CHANGE-CGWB:CGW,1,3,ASC,,,,,,,,,PRIO3,G723,NO,30;
CHANGE-CGWB:CGW,1,3,ASC,,,,,,,,,PRIO4,NONE,NO,20;
CHANGE-CGWB:CGW,1,3,ASC,,,,,,,,,PRIO5,NONE,NO,20;
CHANGE-CGWB:CGW,1,3,ASC,,,,,,,,,PRIO6,NONE,NO,20;
CHANGE-CGWB:CGW,1,3,ASC,,,,,,,,,PRIO7,G729AB,YES,20;
CHANGE-CGWB:CGW,1,3,DSP,60;
CHANGE-CGWB:CGW,1,3,GWSECTOR,0;
CHANGE-CGWB:CGW,1,3,GKDATA,,1719,"PRIMARYRASMANAGERID",,,1719,"SECONDARYRASMANAGERID",,120;
CHANGE-CGWB:CGW,1,3,MGNTDATA,,8000,,443;
CHANGE-CGWB:CGW,1,3,DMCDATA,0;
CHANGE-CGWB:CGW,1,3,WBMDATA,"HP4K-DEVEL",,ENGR;
CHANGE-CGWB:CGW,1,3,WBMDATA,"HP4K-SU",,SU;
CHANGE-CGWB:CGW,1,3,WBMDATA,"HP4K-ADMIN",,ADMIN;
CHANGE-CGWB:CGW,1,3,WBMDATA,"HP4K-READER",,READONLY;
CHANGE-CGWB:CGW,1,3,GWDATA,"PRIMARYRASMANAGERID",;
CHANGE-CGWB:CGW,1,3,H235DATA,NO,NO,"siemensGateway2003",,100,242-191-30-119-188-83-173-161-43-0-70-36-218-74-169-221-78-102-174-170;
CHANGE-CGWB:CGW,1,3,SIPTRERH,NO,,,;
CHANGE-CGWB:CGW,1,3,SIPTRSSA,NO,0.0.0.0,5060,5061,120,0.0.0.0,5060,5061;
CHANGE-CGWB:CGW,1,3,DLSDATA,,10444,NO;
CHANGE-CGWB:CGW,1,3,JB,40,120,20,4,60,200,2;
DIS-SDSU:ALL,,PEN,PER3,1,1,3;
ADD-SBCSU:198,FPP,SIP,1-1-3-12,S0PP,1,1,1,1,1,1,0,0,N,0,0,,,SBDSS1,Y,Y,0,10,N,N,,,5,0,,,172.22.0.93,"","","",,,,;
CHA-ZAND:OPTLOAD;
CHA-SDAT:198,ATTRIBUT,MBCHL;

DIS-BFDAT:2;
H500: AMO BFDAT STARTED
--------------------------------------------------------------------------------
| FCTBLK = 2 BRDBCHL : BCHL60 & BCHL120 STATUS= OK |
--------------------------------------------------------------------------------
| 1. FUNCT : HG3570 1 LINES UNITS BCHLCNT 20 TOTAL BCHAN 20 |
| 2. FUNCT : HG3550 1 LINES UNITS 1 BCHLCNT 10 TOTAL BCHAN 10 |
| 3. FUNCT : HG3530 10 LINES UNITS BCHLCNT 10 TOTAL BCHAN 10 |
| 4. FUNCT : SIP 10 LINES UNITS BCHLCNT 10 TOTAL BCHAN 10 |
--------------------------------------------------------------------------------
DIS-BCSU:TBL,1,1,3;
H500: AMO BCSU STARTED

LTG 1 LTU 1 SRCGRP 1 ALARMNO-LTU 0
-----+-----------+--------+---+-+-+---+-+------------+------------+------------
| | | |S|H|AL-| | | |
| ASSIGNED | MODULE |FCT|E|W|ARM| | INSERTED | HW- | MODULE
PEN | MODULE | TYPE |ID |C|Y|NO | | MODULE |STATE INFO | STATUS
-----+-----------+--------+---+-+-+---+-+------------+------------+------------
3 | Q2324-X500 STMI4 1 * A 0| | Q2324-X500 | 1 -11 - | READY
+--------------------------------+-+------------+------------+------------
| IP ADDRESS : 172. 22. 0.100 B-CHANNELS : 50 BCHLCNT : 50
| IP MODE : IPV4 DHCP V4 : NO DHCP V6 : NO
| BLOCK NO : 2 PRERESERVED LINES ASSIGNED : NO
| 1. FUNCT : HG3570 1 LINES B-CHANNELS : 20 BCHLCNT : 20
| 2. FUNCT : HG3550 1 LINES B-CHANNELS : 10 BCHLCNT : 10
| 3. FUNCT : HG3530 10 LINES B-CHANNELS : 10 BCHLCNT : 10
| 4. FUNCT : SIP 10 LINES B-CHANNELS : 10 BCHLCNT : 10
+--------------------------------+-+------------+------------+------------

DIS-SDSU:ALL,,PEN,PER3,1,1,3;
H500: AMO SDSU STARTED

LTG1 (PERIPHERY)
------
MOUNTING LOCATION MODULE NAME BDL BD(#=ACT) STATUS
------------------- LTG 1 --------------------- READY
-AP370013-----SG 1 LTU 1 --------------------- READY
P203.AP3 1.AP3 1.003 STMI4 A Q2324-X500 READY
LAN CONN. . . . . . . . . . READY
LINK SIGNAL ETHERNET . . . . PRESENT
LAN SPEED . . . . . . . . . 100 MBIT/S
LAN INTERFACE . . . . . . . . FDX (FULL DUPLEX)
CCT FUNCTION BLOCK
0 HG3570_2
1 HG3550_2
2 - 11 HG3530_2
12 - 21 HG3540_2 <--------------- This is function block for SIP right? so i create SIP extension on PEN 1-1-3-12
CCT LINE STNO SI BUS TYPE
001 1844 NOGEN
002 1845 NOGEN
003 1846 NOGEN
004 1847 NOGEN
005 1848 NOGEN
006 1849 NOGEN
007 1850 NOGEN
008 1851 NOGEN
009 1852 NOGEN
010 1853 NOGEN
011 1854 NOGEN
012 1855 PP S0 READY
ELEM DEV. . . . . . SB FCT TERM READY
(ALT_ROUT: N) (S0PP )
LINE: 1855 STNO: 198 SI:VCE
SECURITY LEVEL . . . . . . . (CONF.) "SECURE"
(ACT.) "UNKNOWN"
CCT LINE STNO SI BUS TYPE
013 1856 NOGEN
014 1857 NOGEN
015 1858 NOGEN
016 1859 NOGEN
017 1860 NOGEN
018 1861 NOGEN
019 1862 NOGEN
020 1863 NOGEN
021 1864 NOGEN

DIS-SBCSU:198;
H500: AMO SBCSU STARTED

----------------------------- USER DATA ----------------------------------------
STNO =198 OPT =FPP COS1 =1 DPLN =0
MAINO =198 CONN =SIP COS2 =1 ITR =0
PEN =1- 1- 3- 12 LCOSV1 =1 COSX =0
INS =Y ASYNCT = LCOSV2 =1
SSTNO =N PERMACT =Y LCOSD1 =1 CBKBMAX =5
TRACE =N EXTBUS = LCOSD2 =1 RCBKB =N
ALARMNO =0 DFSVCANA= SPDI =0 RCBKNA =N
HMUSIC =0 FLASH = SPDC1 = CBKNAMB =
PMIDX =0 SPDC2 =
DVCFIG =S0PP LWPAR = PROT =SBDSS1 OPTIDX =10
SMGSUB =N IPCODEC =G723P USERID =""
FIXEDIP =N AUTHREQ =N PASSWD =
IPADDR =172.22.0.93 SECZONE =""
DTMFCTRD=N
------------------- ACTIVATION IDENTIFIERS FOR FEATURES ----------------------
HTOS :N DND :N
HTOD :N VCP :N TWLOGIN :
HTOF :N CWT :N
------------------- FEATURES AND GROUP MEMBERSHIPS ---------------------------
PUGR : ESSTN :
KEYSYS : NOPTNO :
SRCGRP 1 ) TCLASS : 0
HUNT CD :N
------------------- SUBSCRIBER ATTRIBUTES (AMO SDAT) -------------------------
MBCHL
------------------------------------------------------------------------------

DIS-SIPCO:LSNET;
H500: AMO SIPCO STARTED
CENTRAL IP ADDRESSES ( LSNET ) :
-------------------------------------------------------------------
NETADDR ( NET ADDRESS OF THE SYSTEM LAN SEGMENT ) : 172.22.0.0
NETMASK ( NET MASK OF THE SYSTEM LAN SEGMENT ) : 255.255.255.0
IPMODE ( IPMODE ) : IPV4
DEFRT ( ADDRESS OF THE DEFAULT ROUTER ) : 172.22.0.254
CCAADDR ( ADDRESS OF THE CC-A PROCESSOR ) : 172.22.0.93
CCBADDR ( ADDRESS OF THE CC-B PROCESSOR ) : N/A
SURVNET ( NET ADDRESS OF THE SURVIVABILITY NET ) : 0.0.0.0
DHCPV4 ( DHCPV4 ) : N
DHCPV6 ( DHCPV6 ) : N

 

[buang]

Currently the configuration is finished and working good.(see my last configuration post). Thanks for your advice at all. Thread Closed

Thanks in advanced
Buang M. Yulianto

 

[Iamnothere]

Yes, the reference to "HG3540" on the DIS-SDSU command is the "SIP Subscriber". Congratulations!