HIPATH 3000 ROUTES

[mrspyros]

Good day

I have a hipath 3750 with 2 tms2m

1st tms2m on pstn (did 100 - 199)
2nd tms2m going to asterisk server.

1. I want direct dialing from pstn to 2nd tms and hipath
I did that with call forwarding
Someone calls to 60190 and hipath transfers the call to 2nd tms2m as external destination "8090" 80 is the 2nd tms

2. i can call to 2nd tms from any internal call the same way

3. i can call from asterisk to any internal (hipath) phone dialing only the internal number

3. I cannot get external line (pstn) from asterisk to hipath. (with '0')

I think that hipath sees the 2nd tms as external line and any number that comes from it sends it to internal lines.

Is there any way of getting a line from 2nd tms to 1st tms?

 

[mrspyros]

anyone

 

[Bas1234]

Make a trace on how the number is pressented in the Siemens.
I think you need to strip off 1 or more digits.

Can you post a trace?

___________________________________________
It works! Now if only I could remember what I did...

Dain Bramaged
___________________________________________

 

[mrspyros]

Ok.
This is the trace. I call 0 - 2654360114 (0) is the digit for the 1st tms2m but it rejects the call to internal 100 (the center)

----------------------------------------------

30879 -
Monitoring Port : 7869 TMS2M 13 - 1 - 1
-----------------------------------------------------------------------------

Nr | Time | Callnumber/Access | State | Event | Direction | Info
-----+----------+------------------------------+------------------------------+------------------------------+--------------------+------------------
0001 | 08:38:53 | 7869 TMS2M 13 - 1 - 1 | Idle | Monitor On | |
Time = 08:39:12
Slot/Port =
Hipath <- SETUP
cr : 21 (from originating side)
bearer capab : 04 03 80 90 A3
Coding Standard: CCITT
Information Transfer Capability: speech
Transfer Mode: circuit mode
Information Transfer Rate: 64 kbit/s
User information layer 1 protocol: Recommendation
G.711 A-law
channel id : 18 03 A1 83 81
Interface type: other interface
Preferred/Exclusive: preferred
D-Channel Indicator: not the D-channel
Information Channel Selection: as indicated in
following octets
Coding Standard: CCITT
Number/Map: number
Channel/Map Element Type: B-channel units
Channel number: 1
progress ind : 1E 02 80 83
Coding Standard: CCITT
Location: user
Progress Description: origination address is
non-ISDN
calling num : 6C 0C 00 80 32 36 35 34 33 36 30 31 39 30
Type of Number/Numbering Plan: unknown/unknown
Presentation Indicator: presentation allowed
Screening Indicator: user-provided, not screened
Digit(s): 2654360190
called num : 70 0C 80 30 32 36 35 34 33 36 30 31 31 34
Type of Number/Numbering Plan: unknown/unknown
Digit(s): 02654360114

Time = 08:39:12
Slot/Port = 7869 TMS2M 13 - 1 - 1
Hipath -> CALL PROCEEDING
cr : 21 (to originating side)
channel id : 18 03 A9 83 81
Interface type: other interface
Preferred/Exclusive: exclusive
D-Channel Indicator: not the D-channel
Information Channel Selection: as indicated in
following octets
Coding Standard: CCITT
Number/Map: number
Channel/Map Element Type: B-channel units
Channel number: 1

0004 | 08:39:12 | 7869 TMS2M 13 - 1 - 1 | Idle | Setup | Incoming | OAD: 2654360190
0005 | 08:39:12 | 7869 TMS2M 13 - 1 - 1 | Call Initiated | | |
0006 | 08:39:12 | 7869 TMS2M 13 - 1 - 1 | Call Initiated | Call Proc | Outgoing |
0007 | 08:39:12 | 7869 TMS2M 13 - 1 - 1 | Outgoing Call Proc | | |
0008 | 08:39:12 | 100 SLMO8 3 - 1 Master | Idle | Monitor On | |
0009 | 08:39:12 | 100 SLMO8 3 - 1 Master | Call Present | | |
Time = 08:39:12
Slot/Port = 7869 TMS2M 13 - 1 - 1
Hipath -> ALERTING
cr : 21 (to originating side)
facility : 1C 0F 91 A1 0C 02 02 14 8D 06 06 04 00 82 67
02 06
Protocol Profile: ROSE
invokeComp
invokeID 5261
operationValue
globalValue 0 4 0 359 2 6
cCBS-T-Available

0011 | 08:39:12 | 7869 TMS2M 13 - 1 - 1 | Outgoing Call Proc | Alert | Outgoing |
Time = 08:39:14
Slot/Port = 7869 TMS2M 13 - 1 - 1
Hipath <- DISCONNECT
cr : 21 (from originating side)
cause : 08 02 81 90
Coding Standard: CCITT
Location: private network serving the local user
Cause Value: normal call clearing

0013 | 08:39:14 | 7869 TMS2M 13 - 1 - 1 | Outgoing Call Proc | Disconnect | Incoming |
0014 | 08:39:14 | 7869 TMS2M 13 - 1 - 1 | Disconnect Indication | | |
0015 | 08:39:14 | 100 SLMO8 3 - 1 Master | Disconnect Indication | | |
0016 | 08:39:14 | 100 SLMO8 3 - 1 Master | Idle | | |
0017 | 08:39:14 | 100 SLMO8 3 - 1 Master | Idle | Monitor Off | |
Time = 08:39:14
Slot/Port = 7869 TMS2M 13 - 1 - 1
Hipath -> RELEASE
cr : 21 (to originating side)

0019 | 08:39:14 | 7869 TMS2M 13 - 1 - 1 | Disconnect Indication | Release | Outgoing |
Time = 08:39:14
Slot/Port = 7869 TMS2M 13 - 1 - 1
Hipath <- RELEASE COMPLETE
cr : 21 (from originating side)
cause : 08 02 81 90
Coding Standard: CCITT
Location: private network serving the local user
Cause Value: normal call clearing

0021 | 08:39:14 | 7869 TMS2M 13 - 1 - 1 | Disconnect Indication | Release Compl | Incoming |
0022 | 08:39:14 | 7869 TMS2M 13 - 1 - 1 | Idle | | |
----------------------------------------------

 

[Bas1234]

Try to add a new "Dial rule wizard"

Edited dial rule: Any name
Method: MCL Single Stage
Access code: empty
Dial rule format: C0D (C zero D)
min cos: 15
Sched: -
Warning: None

Then add a new "Dialed Digits" like 0CZ and select the dial rule number from above.

___________________________________________
It works! Now if only I could remember what I did...

Dain Bramaged
___________________________________________

 

[mrspyros]

This happens when i use the rule above

-------------------------------------------


30879 -
Monitoring Port : 7869 TMS2M 13 - 1 - 1
-----------------------------------------------------------------------------

Nr | Time | Callnumber/Access | State | Event | Direction | Info
-----+----------+------------------------------+------------------------------+------------------------------+--------------------+------------------
0001 | 08:26:19 | 7869 TMS2M 13 - 1 - 1 | Idle | Monitor On | |
Time = 08:26:39
Slot/Port =
Hipath <- SETUP
cr : 22 (from originating side)
bearer capab : 04 03 80 90 A3
Coding Standard: CCITT
Information Transfer Capability: speech
Transfer Mode: circuit mode
Information Transfer Rate: 64 kbit/s
User information layer 1 protocol: Recommendation
G.711 A-law
channel id : 18 03 A1 83 81
Interface type: other interface
Preferred/Exclusive: preferred
D-Channel Indicator: not the D-channel
Information Channel Selection: as indicated in
following octets
Coding Standard: CCITT
Number/Map: number
Channel/Map Element Type: B-channel units
Channel number: 1
progress ind : 1E 02 80 83
Coding Standard: CCITT
Location: user
Progress Description: origination address is
non-ISDN
calling num : 6C 0C 00 80 32 36 35 34 33 36 30 31 39 30
Type of Number/Numbering Plan: unknown/unknown
Presentation Indicator: presentation allowed
Screening Indicator: user-provided, not screened
Digit(s): 2654360190
called num : 70 0C 80 30 32 36 35 34 33 36 30 31 31 35
Type of Number/Numbering Plan: unknown/unknown
Digit(s): 02654360115

Time = 08:26:39
Slot/Port = 7869 TMS2M 13 - 1 - 1
Hipath -> SETUP ACKNOWLEDGE
cr : 22 (to originating side)
channel id : 18 03 A9 83 81
Interface type: other interface
Preferred/Exclusive: exclusive
D-Channel Indicator: not the D-channel
Information Channel Selection: as indicated in
following octets
Coding Standard: CCITT
Number/Map: number
Channel/Map Element Type: B-channel units
Channel number: 1

0004 | 08:26:39 | 7869 TMS2M 13 - 1 - 1 | Idle | Digit | Incoming | DAD: 02654360115
0005 | 08:26:39 | 7869 TMS2M 13 - 1 - 1 | Idle | Setup | Incoming | OAD: 2654360190
0006 | 08:26:39 | 7869 TMS2M 13 - 1 - 1 | Call Initiated | | |
0007 | 08:26:39 | 7869 TMS2M 13 - 1 - 1 | Call Initiated | Setup Ackn | Outgoing |
0008 | 08:26:39 | 7869 TMS2M 13 - 1 - 1 | Overlap Sending | | |
Time = 08:26:39
Slot/Port = 7869 TMS2M 13 - 1 - 1
Hipath -> DISCONNECT
cr : 22 (to originating side)
cause : 08 02 85 9F
Coding Standard: CCITT
Location: private network serving the remote user
Cause Value: normal, unspecified

0010 | 08:26:39 | 7869 TMS2M 13 - 1 - 1 | Overlap Sending | Disconnect | Outgoing | CAD: 2654360190
0011 | 08:26:39 | 7869 TMS2M 13 - 1 - 1 | Disconnect Indication | | |
0012 | 08:26:39 | 7869 TMS2M 13 - 1 - 1 | Disconnect Indication | Call Proc | Outgoing |
Time = 08:26:39
Slot/Port = 7869 TMS2M 13 - 1 - 1
Hipath <- RELEASE
cr : 22 (from originating side)
cause : 08 02 81 9F
Coding Standard: CCITT
Location: private network serving the local user
Cause Value: normal, unspecified

Time = 08:26:39
Slot/Port = 7869 TMS2M 13 - 1 - 1
Hipath -> RELEASE COMPLETE
cr : 22 (to originating side)

0015 | 08:26:39 | 7869 TMS2M 13 - 1 - 1 | Disconnect Indication | Release | Incoming |
0016 | 08:26:39 | 7869 TMS2M 13 - 1 - 1 | Idle | | |

 

[mrspyros]

And i hear (from asterisk) the message all the lines are buisy

 

[mrspyros]

I have to mention that the trace comes from the tms connected to asterisk

 

[Bas1234]

Tried dialing with 000XXXXXXXXXX

So 1 zore for outside line on the siemens and one for the Asterisk.

___________________________________________
It works! Now if only I could remember what I did...

Dain Bramaged
___________________________________________

 

[Bas1234]

If that works try C00Z instead of C0Z

___________________________________________
It works! Now if only I could remember what I did...

Dain Bramaged
___________________________________________