Help with PRIU Daughter Card

[molotovich]

For some reason, it gets detected as a DIG STA 8 st startup, attaching boot log:

CPU Board Version is: 0xD0
CPU PLD Version is: 0x17
CPUID: 0x02 Present: 0x00 Present2: 0x02
Using FPGA build 0x0000005E
Programming FPGA ...
FPGA ID 0x01 Version 0x00 Build 0x0000005E
Initialising NAND device.. registering..
Added device: Hynix 64MB NAND (small block) - 0x0000

Reading main image file..
Read complete
Expanding MPPC image ...
Expansion complete

Alarm Logging enabled (max entries=8, in use=0)
Audit Logging enabled (max entries=123, in use=6)
NoCacheStaticHeap=26817900 NoCacheDynamicHeap=5687956 Overflow=0
Constructor StaticHeap=12620 DynamicHeap=92139096
Factory Test Status 00000001
Product Variation Status 00000000
About to create NVConfig
Loaded NVConfig
Factory Release version 4.0(0) built on Aug 20 2007 at 11:59:44
FPGA: ID=0x01 Issue=0x00 BuildNum=0x0000005e
Broadcom Switch Mode was 0x05 now 0x06
EthChipRevId: 0x01 EthPhyId: 0x0143bc30
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
++++++++++++++++++++ LIST OF MODULES ++++++++++++++++++++
+------------------------------------------------------------
+ Slot 1: Base DIGSTA8 Board=0x13 PLD=0x06
+ Mezzanine DIGSTA8 Board=0x03 PLD=0x0a <---- ### this is the PRI card
+------------------------------------------------------------
+ Slot 2: Base PHONE8 Board=0x04 PLD=0x03
+ Mezzanine CARRIER Board=0x03 PLD=0x07
+------------------------------------------------------------
+ Slot 3: Base PHONE8 Board=0x04 PLD=0x03
+ Mezzanine NONE
+------------------------------------------------------------
+ Slot 4: Base PHONE8 Board=0x03 PLD=0x03
+ Mezzanine NONE
+------------------------------------------------------------
+++++++++++++++++ END OF LIST OF MODULES +++++++++++++++

Already validated the part number, I dont know why is doung this, is a brand new digital card and pri card, and this is being extracted from a NEW Ip office, i dont get why it doesnt appear as PRI

Thanks

 

[molotovich]

Update:

After some troubleshooting, I removed the expansion board of the PHONE8 card, and apparently the PRIU card is being detected, now i get errors while loading the PRIU DSP, any ideas?

 

[intrigrant]

Kaput

A simple mind delivers great solutions

 

[amriddle01]

Something is very wrong there, there is also no daughter board that should show as "carrier", do you have a spare 500v2 to try, it may not be the cards



"No problem monkey socks

 

[AACon]

I'm wondering if this has anything to do with it? I haven't looked at my boot log to see if it's different. You say it's a "new" ip office...but is it a v2, v1? What firmware is on it?

Some cards do not function at old releases.

Factory Release version 4.0(0) built on Aug 20 2007 at 11:59:44

-Austin
ACE: Implement IP Office

 

[amriddle01]

I noticed the same thing...but as he said it's "new" I guessed that was some boot file version or something



"No problem monkey socks

 

[AACon]

Yeah not sure. I don't really feel like hooking up a serial cable and rebooting my ipo when i'm not gettin paid for it

-Austin
ACE: Implement IP Office

 

[tlpeter]

If i am correct then a brand new IP500v1 came on 4.0.0 and you need to upgrade it first to get it working.
I wonder if that is what is causing this problem.


BAZINGA!

I'm not insane, my mother had me tested!

 

[AACon]

They did, from what I remember as well. That's why I mentioned it.

-Austin
ACE: Implement IP Office

 

[molotovich]

Update:

I updated the old "new" IPO 4.0 to 5.0 (26) the card started working, it gets detected as PRIU, the problem i was having yesterday after all this was that all channels appears as out of service (I suspect service provider fault, to be cleared today)

Question: the Manager complains that the system has more PRI channels programmed than allowed by license, the problem is that AFAIK the IPO comes with 8 channels per PRI enabled, and the customer purchased a license for 2 more channels, that would be 10, is that correct?

 

[AACon]

That is correct. Look at your channels, and put only the first 10 in service, and the rest out of service (which they are by default).
I knew it was a firmware problem. I'm so smrt.

-Austin
ACE: Implement IP Office

 

[amriddle01]

So not "New" at all then..... it would have been solved quicker with that info. FYI 4.0.0 is a non functioning firmware just to allow access to the system so you can upgrade it to the version you need. And yes adding a licence for 2 channels will make it 10 but you need to add the licence to the system and make sure it validates, then knock all the channel fields in the PRI config down to 10 and the alarm will go away



"No problem monkey socks

 

[molotovich]

Ok: problem, provider has cleared the lines, but they say they dont see the IPO at the other end, this is the startup i get from the RS232 port:

CPU Board Version is: 0xD0
CPU PLD Version is: 0x17
CPUID: 0x02 Present: 0x00 Present2: 0x02
Using FPGA build 0x00000817
Programming FPGA ...
FPGA ID 0x01 Version 0x01 Build 0x00000817
Initialising NAND device.. registering..
Added device: Hynix 64MB NAND (small block) - 0x0000

Reading main image file..
Read complete
Expanding MPPC image ...
Expansion complete

Alarm Logging enabled (max entries=8, in use=0)
Audit Logging enabled (max entries=123, in use=32)
NoCacheStaticHeap=30700360 NoCacheDynamicHeap=1805496 Overflow=0
Constructor StaticHeap=12860 DynamicHeap=83478488
Factory Test Status 00000001
Product Variation Status 00000000
RTC FPGA Not Initialised
RTC FPGA Not Initialised
About to create NVConfig
Loaded NVConfig
found FLASH file: ..\vcomp\48105ak.310, len=e2
found FLASH file: ..\vcomp\48105ae3.312.03, len=1ee4e
found FLASH file: ..\platform\onehz.bin, len=3e80
found FLASH file: ding.pcm, len=40a
found FLASH file: ..\vcomp\482ak.311.09, len=10e
found FLASH file: ..\vcomp\48204ae6.311.09, len=1da6a
FPGA: ID=0x01 Issue=0x01 BuildNum=0x00000817
Broadcom Switch Mode was 0x05 now 0x06
EthChipRevId: 0x01 EthPhyId: 0x0143bc30
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+ loader: 1.3
+ cpu: id 2 board d0 pld 17 type c10 options 2
+ fpga: id 1 issue 1 build 817
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
++++++++++++++++++++ LIST OF MODULES ++++++++++++++++++++
+------------------------------------------------------------
+ Slot 1: Base DIGSTA8 Board=0x13 PLD=0x06
+ Mezzanine PRIS U Board=0x03 PLD=0x0a
+------------------------------------------------------------
+ Slot 2: Base PHONE8 Board=0x03 PLD=0x03
+ Mezzanine NONE
+------------------------------------------------------------
+ Slot 3: Base PHONE8 Board=0x04 PLD=0x03
+ Mezzanine NONE
+------------------------------------------------------------
+ Slot 4: Base PHONE8 Board=0x04 PLD=0x03
+ Mezzanine NONE
+------------------------------------------------------------
+++++++++++++++++ END OF LIST OF MODULES +++++++++++++++
RegisterDS8Card!
PRI: configurePriPluginCard slot=1 universal=1 single=1
PRI: Identified: mod_card_type=4, ds1=0, r2=0
PRI: Bases= 45009000 4500a000 45008000 4500b000
Falc56 detected, VSTR 0x05, WID 0x4d
PRIU DSP: loading image to addr 0090, size 32480
PRIU DSP: checking image
PRIU DSP: image load check completed
PRIU DSP: image loaded and running
PRIU DSP 1: image version 02.00 (release 00)
SLOT 1: PRI30 Module Added
Conf DSP: loading image to addr 0090, size 32480
Conf DSP: checking image
Conf DSP: image load check completed
Conf DSP: image loaded and running
Confer DSP - image version 01.02 (release 00)
DelicDriver:elicDriver( base=42010000, no_ports=8)
Cerating IP408_DelicDriver at 5006
DelicBoot::CheckFirmware(), Version= 5b016
DelicBoot::SetApplicationSpecificRegisters(), CSTRAP= 3b6
Delic object Initialised at 6133
MAKEBUNDLE size=8 id=6.2
Configuration of Slot modules environment
SEC: Initialisation OK. Base = 0f040000. Type = SEC1P0. Coherent Cache = 1.
Unit warm start = 0
RTC BRAM = EDED1234
Configuration of interrupts
DVP 0: Constructor - 8 lines firstPort 8 - base TS 0 - deviceType 2
DVP 0: VpBootLoad successful (63 ms)
DVP Product VP_DVP_PRODUCT_VE_880 found
DVP 0: Boot complete event
DVP 0: RevCode=0xB ProdId=0x80 SwVer=1.02
DVP 0: CreateLines entry adding start 8 end = 16 before lines = 8 (firstPort 8)
Setting default options for DVP(All Lines)...
DVP 0: Initialisation complete event 0xf0
DVP 0: L08 P08: Ring - t/slot( 8: 8) - law(A) - DTMF(1 1) - pulse OFF - Neutral - MW
DVP 0: L09 P09: Ring - t/slot( 9: 9) - law(A) - DTMF(1 1) - pulse OFF - Neutral - MW
DVP 0: L10 P10: Ring - t/slot(10:10) - law(A) - DTMF(1 1) - pulse OFF - Neutral - MW
DVP 0: L11 P11: Ring - t/slot(11:11) - law(A) - DTMF(1 1) - pulse OFF - Neutral - MW
DVP 0: L12 P12: Ring - t/slot(12:12) - law(A) - DTMF(1 1) - pulse OFF - Neutral - MW
DVP 0: L13 P13: Ring - t/slot(13:13) - law(A) - DTMF(1 1) - pulse OFF - Neutral - MW
DVP 0: L14 P14: Ring - t/slot(14:14) - law(A) - DTMF(1 1) - pulse OFF - Neutral - MW
DVP 0: L15 P15: Ring - t/slot(15:15) - law(A) - DTMF(1 1) - pulse OFF - Neutral - MW
DVP 0: Initialisation complete.
DVP 1: Constructor - 8 lines firstPort 0 - base TS 0 - deviceType 2
DVP 1: VpBootLoad successful (63 ms)
DVP Product VP_DVP_PRODUCT_VE_880 found
DVP 1: Boot complete event
DVP 1: RevCode=0xB ProdId=0x80 SwVer=1.02
DVP 1: CreateLines entry adding start 0 end = 8 before lines = 8 (firstPort 0)
Setting default options for DVP(All Lines)...
DVP 1: Initialisation complete event 0xff
DVP 1: L00 P16: Ring - t/slot(16:16) - law(A) - DTMF(1 1) - pulse OFF - Neutral - MW
DVP 1: L01 P17: Ring - t/slot(17:17) - law(A) - DTMF(1 1) - pulse OFF - Neutral - MW
DVP 1: L02 P18: Ring - t/slot(18:18) - law(A) - DTMF(1 1) - pulse OFF - Neutral - MW
DVP 1: L03 P19: Ring - t/slot(19:19) - law(A) - DTMF(1 1) - pulse OFF - Neutral - MW
DVP 1: L04 P20: Ring - t/slot(20:20) - law(A) - DTMF(1 1) - pulse OFF - Neutral - MW
DVP 1: L05 P21: Ring - t/slot(21:21) - law(A) - DTMF(1 1) - pulse OFF - Neutral - MW
DVP 1: L06 P22: Ring - t/slot(22:22) - law(A) - DTMF(1 1) - pulse OFF - Neutral - MW
DVP 1: L07 P23: Ring - t/slot(23:23) - law(A) - DTMF(1 1) - pulse OFF - Neutral - MW
DVP 1: Initialisation complete.
DVP 1: CreateLines entry adding start 8 end = 16 before lines = 8 (firstPort 0)
DVP 1: L08 P24: Ring - t/slot(24:24) - law(A) - DTMF(1 1) - pulse OFF - Neutral - MW
DVP 1: L09 P25: Ring - t/slot(25:25) - law(A) - DTMF(1 1) - pulse OFF - Neutral - MW
DVP 1: L10 P26: Ring - t/slot(26:26) - law(A) - DTMF(1 1) - pulse OFF - Neutral - MW
DVP 1: L11 P27: Ring - t/slot(27:27) - law(A) - DTMF(1 1) - pulse OFF - Neutral - MW
DVP 1: L12 P28: Ring - t/slot(28:28) - law(A) - DTMF(1 1) - pulse OFF - Neutral - MW
DVP 1: L13 P29: Ring - t/slot(29:29) - law(A) - DTMF(1 1) - pulse OFF - Neutral - MW
DVP 1: L14 P30: Ring - t/slot(30:30) - law(A) - DTMF(1 1) - pulse OFF - Neutral - MW
DVP 1: L15 P31: Ring - t/slot(31:31) - law(A) - DTMF(1 1) - pulse OFF - Neutral - MW
RouteSystem::LAN1 Complete...
RouteSystem::LAN2 Complete...
RouteSystem:: LAN1 ipaddr=C0A80803 ipmask=FFFFFF00
RouteSystem:: LAN2 ipaddr=C0A82B01 ipmask=FFFFFF00
Allow licence handler to run early...
DVP 0: Clock recovery on channel - L00 P-1
DVP 0: Clock recovery on channel - L02 P-1
DVP 0: Clock recovery on channel - L04 P-1
DVP 0: Clock recovery on channel - L06 P-1
Configuration::Attempting to read from FLASH...
FlashConfigIO::Load(0)
SetSystemLocale: esm, 2
SetSystemLocale: esm, 2
Control Unit type IP 500 last version 5.0(26)
Diffserve settings - VAL=b8 MASK=fcnnels(0): free_upri_chans = 2
SetSystemLocale: esm, 2
Configuration::Complete
RouteSystem::Starting DHCP Server (LAN1)
RouteSystem::Starting DHCP Server (LAN2)
ObjectMemoryPool: SSIComponentId, filled 2 times
ObjectMemoryPool: SSIComponentId, filled 3 times
Platform:iscover Possible LAN Attached Units...
TDMLink 1 Online
New PCMCIA Card in slot 0: vs1=0 vs2=0
New PCMCIA Card in slot 0: Vcc=1 Vpp=1
PCMCIA0: Detected the CIS - size 182 bytes
PCMCIA0 ConfigInfo: DevType=0x0d FuncCode=0x04 SysInit=0x01 ManuCode=0x947f ManuInfo=0x0007
DiskInfo: m_diskIFType=1 m_extensionInfoIsValid=1 m_isSilcon=1 m_hasUniqueSerialNumber=0
PCMCIA Card in slot 0: Vcc=1 Vpp=0
FlashPCDriver::SetCommonMemoryWindow: windowSize=2048 sizeExponent=0x0e HT=8 ST=6 SL=24
PCMCIA Card configured in slot 0
PCMCIA0 ConfigInfo: DevType=0x0d FuncCode=0x04 SysInit=0x01 ManuCode=0x947f ManuInfo=0x0007
PCMCIA0 ConfigInfo: DevType=0x0d FuncCode=0x04 SysInit=0x01 ManuCode=0x947f ManuInfo=0x0007
PCMCIA0 ConfigInfo: DevType=0x0d FuncCode=0x04 SysInit=0x01 ManuCode=0x947f ManuInfo=0x0007
System not shut down properly - checking integrity of Flash File System ...
pcmcia_card_is_ata: result=1
Scanning drive A: for errors
Drive 0 information:
Volume NO NAME (7e74-6a60):
No of sectors: 1000881 (last element in FAT: 62523):
Disk size: 512451072 bytes
Disk free: 0 bytes
FAT Type: FAT-16
Checking clusters
Checking directories and files
Scanning directory <>
Scanning directory <LVMAIL >
Scanning directory <KOR >
Scanning directory <NLD >
Scanning directory <NOR >
Scanning directory <PTB >
Scanning directory <PTG >
Scanning directory <RUS >
Scanning directory <SVE >
Scanning directory <CHS >
Scanning directory <DAN >
Scanning directory <DEU >
Scanning directory <ENG >
Scanning directory <ENU >
Scanning directory <ESM >
Scanning directory <ESP >
Scanning directory <ESS >
Scanning directory <FIN >
Scanning directory <FRA >
Scanning directory <FRC >
Scanning directory <ITA >
Scanning directory <JPN >
Scanning directory <ZHH >
Scanning directory <AAG >
Scanning for lost files
Scan of drive A: complete
filesys: pc_repairdisk: 1180 ms
... check completed. Flash File System did not need to be repaired.
PCMCIA0 ConfigInfo: DevType=0x0d FuncCode=0x04 SysInit=0x01 ManuCode=0x947f ManuInfo=0x0007
Callback ../pcmcia/pcmcia.cpp Line 373 took 1281mS
Platform:iscover TDM Attached Units...
Firewall Validating LAN1
Firewall Validating LAN2
Checking WAN
IPSecMng::Starting IPSec module...
RightsManager::Init() - starting
(Falc2: UpdateType: 4 0 0 -> 6 0 1)
FixUpUniversalLine: 1 -> 7
Slot 1, Falc 1: Configure
Slot 1, Falc 1: pri_type: 6 HDB3 NO CRC
Slot 1, Falc 1: DriverInit56R2
Slot 1, Falc 1: ModifyRxEqualizerRam
Slot 1, Falc 1: Configured for R2
Slot 1, Falc 1: PLL locked
Slot 1, Falc 1: PLL locked (25usec)
ObjectMemoryPool: SSIComponentId, filled 4 times
CREATE UNIT IP 500
CREATE UNIT PHONE8
ObjectMemoryPool: SSIComponentId, filled 5 times
CREATE UNIT PHONE8
CREATE UNIT PHONE8
ObjectMemoryPool: SSIComponentId, filled 6 times
CREATE UNIT DIG DCPx16 V2
GODTDMLink::LinkUp line id 6 transitioned to up
ObjectMemoryPool: SSIMessage, filled 2 times
CREATE UNIT DIGSTA8/PRIS U
>>> IP500 DIG STA 8: slotNum=20 devno=2 badd=1
LAN1 c0a80803
LAN2 c0a82b01
SNMP::SNMP Server is disabled
SNMPTrapper::SNMP Trap Generator bound to UDP src port 4097
Loading Software Version (5.0(26))
IPOFFICE: Thu 2013/5/30 22:45:41 FreeMem=76161252 FreeNoC=1532492
Inband Exception Handling Enabled
Platform does support UNICODE
Config does NOT contain UNICODE strings
System Locale: esm, System Charset: 2
Initialisation complete starting TA

Slot 1, Falc 1: LOCK RAI crc=0 set=0 FMR1=06 FMR2=02
SetSystemLocale: esm, 2
SetSystemLocale: esm, 2
SetSystemLocale: esm, 2
TimeKeeper: UTC Offset 18000 seconds
TimeKeeper: UTC Offset 18000 seconds
SetSystemLocale: esm, 2
SetSystemLocale: esm, 2
SetSystemLocale: esm, 2

Any help would be appreciated, the system sees the channels, the card has been changed in the manager to a PRI30, I dont know what else to do, it has 8 channels programmed as R2DIOD, the rest are out of service, and it still complains about the licenses of the channels

Thanks

 

[amriddle01]

I think you need some training, boot logs will not help troubleshoot and you are changing the wrong fields to clear the licence error



"No problem monkey socks

 

[molotovich]

And yes adding a licence for 2 channels will make it 10 but you need to add the licence to the system and make sure it validates, then knock all the channel fields in the PRI config down to 10 and the alarm will go away"

Nope, it is still there thanks for the help

 

[amriddle01]

You are changing the wrong fields or it isn't a valid licence



"No problem monkey socks

 

[AACon]

Yeeah you might need a refresher in IPO setup...

-Austin
ACE: Implement IP Office

 

[molotovich]

Maybe I do! but the problem is I am doing this practically "by the book"

another suspect is the Balum, will change that too, thanks for the support.

BTW: I didnt knew about the 4.0 release I found out last night at 11 pm

 

[amriddle01]

Look here

"No problem monkey socks

 

[molotovich]

Mine is an R2, I dont have that parameter, I only have 30 channels

Where is it? I have E1R2