Help with basic configuration of PIX501 1

[drmohlen]

I have been trying to configure our test pix501 with a basic configuration of allowing a users to be able to access outside ( Internet) but unfortunatly the configuration fails measurabley.

I have copied the result of show run command bellow and was wondering if any one can either correct the following config or send me the basic command which would allow me to add to the pix from where the pix is set to the factory default settings.

Many Thanks



show run
: Saved
:
PIX Version 6.3(3)
interface ethernet0 auto shutdown
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
hostname test_1
domain-name Test
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
access-list 100 permit icmp any any echo-reply
access-list 100 permit icmp any any time-exceeded
access-list 100 permit icmp any any unreachable
access-list inbound perm
access-list inbound permit ip any any
access-list inbound permit udp any any
access-list inside_public permit tcp any any
pager lines 24
logging on
logging monitor debugging
logging history alerts
logging host inside 192.168.11.3
mtu outside 1500
mtu inside 1500
ip address outside x.x.x.34 255.255.255.0
ip address inside 192.168.11.1 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
pdm history enable
arp timeout 14400
global (outside) 2 interface
nat (inside) 1 access-list inside_public 0 0
nat (inside) 2 0.0.0.0 0.0.0.0 0 0
access-group 100 in interface outside
access-group inbound in interface inside
route outside 0.0.0.0 0.0.0.0 x.x.x.46 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server RADIUS protocol radius
aaa-server LOCAL protocol local
http server enable
http 192.168.11.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd address 192.168.11.2-192.168.11.129 inside
dhcpd dns 62.6.40.162 62.6.40.178
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd enable inside
terminal width 80
Cryptochecksum:61bdbc761935317c0700466aabedbdcc
: end
test_1(config)#

 

[Supergrrover]

Your interface is shut down

interface ethernet0 auto shutdown

You need to do a "no shut" on it to bring it up.



Brent
Systems Engineer / Consultant
CCNP, CCSP

 

[Supergrrover]

You probably want to take out these lines. They aren't doing anything

nat (inside) 1 access-list inside_public 0 0
access-group inbound in interface inside (all traffic is allowed out by default.)


Brent
Systems Engineer / Consultant
CCNP, CCSP

 

[drmohlen]

Thank you very much for that,it worked! I can't believe the problem was as simple as that.