help on 'slip' and not able place external calls-Nortel to Ascom

[telekon1]

To John Poole and TeK-Tip forum:

I am having 'slip' error and I changed clock as per Ascom in addition not able to access '9'. I have a physical cable from Nortel Succession PRI card with D-channel to Ascom IP PRI. i installed another cable and still having slips. I can dial from Ascom to a Nortel DN but not able to dial from Nortel DN to Ascom handset. I am sending the present configuration of the Nortel and at the bottom of the WORD file is the sent copy from Ascom. I can only get it to work the present clock set up and I do not understand why I am not able to configure as a TIE.

I viewed bits of information on 'Meridian' thread as help to me configure the Nortel.

I have two problems but they might be related as per the current configuration.

Thanks, in advance!

This is programming so the Nortel knows what kind of route this is, I tried TIE and DID but the only way to receive dial tone and process messaging thru the Ascom gateway is this way, not saying there might be another but this way I am able to complete programming



REQ: PRT
TYPE: RDB
CUST 0
ROUT 11

TYPE RDB
CUST 00
ROUT 11
DES ASCOM_NURSECALL
TKTP DID
M911_ANI NO
M911_TONE NO
NPID_TBL_NUM 0
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI
ISDN YES
MODE PRA
IFC NI2- I tried isig and qsig but I was not able to get this to complete programming. CBCR NO
NCOS 0
SBN NO
PNI 00000
NCNA YES
NCRD NO
CHTY BCH
CPFXS YES
CPUB OFF
DAPC NO
BCOT 0
INTC NO
MBXR NO
MBXOT NPA
MBXT 0
DSEL VOD
PTYP PRI
CNDP UKWN
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
RANX NO
SRCH LIN- this should not able matter but I normally set this to linear
TRMB YES
STEP
ACOD 78 need this so I can identify the trunk access and route
TCPP NO
PII NO
AUXP NO
TARG 01
CLEN 1
BILN NO
OABS
INST
ICIS YES
TIMR ICF 512 change timers to 384 but no change
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896


PAGE 002

SFB 3
NBS 2048
NBL 4096

IENB 5
VSS 0
VGD 6
DRNG NO
CDR NO
VRAT NO
MUS NO
RACD NO
EQAR NO
OHQ NO
OHQT 00
TTBL 0
ATAN NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
ARDN NO
CTBL 0
AACR NO

REQ: END
>LD 20

PT0000
These are the channels which are programmed as DID, I tried TIE but was not able to get ASCOM to get access which in other words did not work.

DES ASCOM_NURSECALL
TN 024 01
TYPE DID
CDEN SD
CUST 0
TRK PRI
PDCA 1
PCML MU
NCOS 0
RTMB 11 1
B-CHANNEL SIGNALING
NITE
STRI/STRO OWK OWK
AST NO
IAPG 0
CLS UNR DTN CND ECD WTA LPR APN THFD HKD SPCD
P10 VNL
TKID
AACR NO
DATE 22 JUL 2014


These trunks match the channels on the Ascom ‘STATE’ when I access or if there is any traffic from the PBX to the Ascom

REQ: LTM
CUST 0
ROUT 11

TYPE TLST
TKTP DID
ROUT 11
DES ASCOM_NURSECALL
TN 024 01 MBER 1 ASCOM_NURSECALL
TN 024 02 MBER 2 ASCOM_NURSECALL
TN 024 03 MBER 3 ASCOM_NURSECALL
TN 024 04 MBER 4 ASCOM_NURSECALL
TN 024 05 MBER 5 ASCOM_NURSECALL
TN 024 06 MBER 6 ASCOM_NURSECALL
TN 024 07 MBER 7 ASCOM_NURSECALL
TN 024 08 MBER 8 ASCOM_NURSECALL
TN 024 09 MBER 9 ASCOM_NURSECALL
TN 024 10 MBER 10 ASCOM_NURSECALL
TN 024 11 MBER 11 ASCOM_NURSECALL
TN 024 12 MBER 12 ASCOM_NURSECALL
TN 024 13 MBER 13 ASCOM_NURSECALL
TN 024 14 MBER 14 ASCOM_NURSECALL
TN 024 15 MBER 15 ASCOM_NURSECALL
TN 024 16 MBER 16 ASCOM_NURSECALL
TN 024 17 MBER 17 ASCOM_NURSECALL
TN 024 18 MBER 18 ASCOM_NURSECALL
TN 024 19 MBER 19 ASCOM_NURSECALL
TN 024 20 MBER 20 ASCOM_NURSECALL
TN 024 21 MBER 21 ASCOM_NURSECALL
TN 024 22 MBER 22 ASCOM_NURSECALL
TN 024 23 MBER 23 ASCOM_NURSECALL
TN 034 01 MBER 24 ASCOM_NURSECALL


This the way the D-channel card is programmed to associate with the Ascom trunk

ADAN DCH 2
CTYP MSDL
GRP 0
DNUM 9
PORT 0
DES ASCOM24
USR PRI
DCHL 24
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT I tried to change to INT and changed the ascom side to slave and it stopped working I could get the ascom to work at this setting.

IFC NI2
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE USR this setting equals ‘slave’
CNEG 1
RLS ID **
RCAP COLP
MBGA NO
OVLR NO
OVLS NO
T310 120
T200 3
T203 10
N200 3
N201 260
K 7
BSRV NO

REQ
DTC001

This just shows the state of the D-channel as ‘up’ or enabled state
DCH 002 : OPER EST ACTV AUTO DES : ASCOM24





This shows or equal the ‘state’ side of the ascom so when I access channel one on the Nortel is shows line state 1 on the ascom side

PRI* TRK LOOP 24 - ENBL
FFMT/LCMT/YALMT: ESF/B8Z/FDL
SERVICE RESTORE: YES
YEL ALM PROCESS: YES
ALARM STATUS : NO ALARM
CH 01 - IDLE DID VOD * CH 02 - IDLE DID VOD *
CH 03 - IDLE DID VOD * CH 04 - IDLE DID VOD *
CH 05 - IDLE DID VOD * CH 06 - IDLE DID VOD *
CH 07 - IDLE DID VOD * CH 08 - IDLE DID VOD *
CH 09 - IDLE DID VOD * CH 10 - IDLE DID VOD *
CH 11 - IDLE DID VOD * CH 12 - IDLE DID VOD *
CH 13 - IDLE DID VOD * CH 14 - IDLE DID VOD *
CH 15 - IDLE DID VOD * CH 16 - IDLE DID VOD *
CH 17 - IDLE DID VOD * CH 18 - IDLE DID VOD *
CH 19 - IDLE DID VOD * CH 20 - IDLE DID VOD *
CH 21 - IDLE DID VOD * CH 22 - IDLE DID VOD *
CH 23 - IDLE DID VOD * CH 24 - DCH 2
.

DTI000

 

[trvlr1]

Your programming needs to match the Ascom system, What is the set up there for the route? You also need to match up the basic circuit parameters too, ie B8S / ESF etc. These can be printed in your Nortel from LD 22 (prt CEQU) Do not know anything on the Ascom so you are on your own there.

 

[bboyko]

On the D channel, since the Nortel is set to 'usr', the Ascom would need to be set as 'network' or 'master'. Sorry, I don't know what Ascom calls it.

 

[telekon1]

I have access to the Ascom IP switch and I have changed the settings from 'MASTER' and changed 'NI' and this setting did not change my 'slip' count. Ascom sent me a setting to match their IP switch that was from their engineering dept. I already had it set and working but still did not clear my 'slip'. Nortel supports "QSIG' but unable to work using that setting. I tried changing from DID to TIE but i do not know how to get by the prompt 'RTN'? I stopped and configured back as DID. I have my COT programmed as DID and they are working with no slips. Ascom has 'swap TR/RV' 'NI mode' 'MASTER SLAVE' and 'QSIM' and that is it for PRI settings.

Thank you in advance for all those contributing.

 

[bignose21]

Slips are layer 1 so concentrate on what is in CEQU and LD 73 SYTI, stat the clock in LD 60 does it look ok, etc.