Help on MD110 BC9

[jaylek]

Due to power failure the system crashed and I have changed the HDU6. Loaded the INL and send a wrong LIM disposition table. My original table was this.
It is a 2 LIM system.
<GJLCP:LIM=1;
GROUP JUNCTOR LINE CONNECTION DATA
EQU GS MULT NO GS CON LIM
1-3-00-0 0-3 0 2
1-2-00-0 0-2 0 2
1-1-00-0 0-1 0 2
1-0-00-0 0-0 0 2

END

<GJLSP:GSMULT=0-0&&7-30;
GROUP JUNCTOR LINE STATUS
EQU = 1-0-00-0 GS-MULT 0-0
GS SIDE 0 ACTIVE ACTIVATED SIGNALLING MASTER LINK
SIDE 0 ALARM 0000 0000 0000 0000


EQU = 1-1-00-0 GS-MULT 0-1
GS SIDE 0 ACTIVE ACTIVATED NOT SIGNALLING NO CLOCK CONTROL
SIDE 0 ALARM 0000 0000 0000 0000


EQU = 1-2-00-0 GS-MULT 0-2
GS SIDE 0 ACTIVE ACTIVATED NOT SIGNALLING NO CLOCK CONTROL
SIDE 0 ALARM 0000 0000 0000 0000


EQU = 1-3-00-0 GS-MULT 0-3
GS SIDE 0 ACTIVE ACTIVATED NOT SIGNALLING NO CLOCK CONTROL
SIDE 0 ALARM 0000 0000 0000 0000


EQU = 2-0-00-0 GS-MULT 0-4
GS SIDE 0 ACTIVE ACTIVATED NOT SIGNALLING SYNC RECEIVING
SIDE 0 ALARM 0000 0000 0000 0000


EQU = 2-1-00-0 GS-MULT 0-5
GS SIDE 0 ACTIVE ACTIVATED NOT SIGNALLING NO CLOCK CONTROL
SIDE 0 ALARM 0000 0000 0000 0000


EQU = 2-2-00-0 GS-MULT 0-6
GS SIDE 0 ACTIVE ACTIVATED NOT SIGNALLING NO CLOCK CONTROL
SIDE 0 ALARM 0000 0000 0000 0000


EQU = 2-3-00-0 GS-MULT 0-7
GS SIDE 0 ACTIVE ACTIVATED SIGNALLING NO CLOCK CONTROL
SIDE 0 ALARM 0000 0000 0000 0000



END
What I send was
<GJLCP:LIM=1;
GROUP JUNCTOR LINE CONNECTION DATA
EQU GS MULT NO GS CON LIM
1-3-00-0 0-8 0 2
1-2-00-0 0-7 0 2
1-0-00-0 0-2 0 2
1-1-00-0 0-1 0 2

END

<GJLCP:LIM=2;
GROUP JUNCTOR LINE CONNECTION DATA
EQU GS MULT NO GS CON LIM
2-3-00-0 0-14 0 1
2-2-00-0 0-13 0 1
2-1-00-0 0-5 0 1
2-0-00-0 0-4 0 1

END

<GJLSP:LIM=2;
GROUP JUNCTOR LINE STATUS
EQU = 2-0-00-0 GS-MULT 0-4
GS SIDE 0 ACTIVE ACTIVATED NOT SIGNALLING NO CLOCK CONTROL
SIDE 0 ALARM 0000 0000 0000 0000


EQU = 2-1-00-0 GS-MULT 0-5
GS SIDE 0 ACTIVE ACTIVATED SIGNALLING SYNC RECEIVING
SIDE 0 ALARM 0000 0000 0000 0000


EQU = 2-2-00-0 GS-MULT 0-13
GS SIDE 0 ACTIVE ACTIVATED NOT SIGNALLING NO CLOCK CONTROL
SIDE 0 ALARM 0000 0000 0000 0000


EQU = 2-3-00-0 GS-MULT 0-14
GS SIDE 0 ACTIVE ACTIVATED NOT SIGNALLING NO CLOCK CONTROL
SIDE 0 ALARM 0000 0000 0000 0010

Now the issue is it always relaods and the message is
MESSAGE FROM OPERATING SYSTEM:
RELOAD REQUESTED
SYSTEM INITIATED DATA
So I cant do the programming. After the reload that will vanish.
<DCSSP;LIM=ALL;
CONTROL SYSTEM INFORMATION

LIM CSSIDE A CSSIDE B BLOCKWORD
1 EXECUTING NOT INITIATED
2 NOT INITIATED EXECUTING
The system is fully down now.Please help to solve this

 

[Mycom]

If you are starting the system from an INL and have entered the wrong LIM disp why not start all over again from scratch and enter the correct LIM disp this time.