Help on 61c to Cisco Integration

[breakbuddy1]

I am getting PRI222, and 229 errors when calling the Cisco sets and PRI227 errors when Cisco sets are calling the 61. Books says it's some protocol error where it either is NULL or doesn't exsist. We have 7xxx extensions on the PBX and 3XXX on the Cisco.

Here is the config that I have on the PBX ANY help on this matter is appreciated. Here is my configs-

ROUT 6


TYPE RDB
CUST 00
ROUT 6
DES CISCO_TIE
TKTP TIE
NPID_TBL_NUM 0
ESN NO
CNVT NO
SAT NO
RCLS EXT
DTRK YES
DGTP PRI
ISDN YES
MODE PRA
IFC S100
SBN NO
PNI 00000
NCNA YES
NCRD NO
CHTY BCH
CTYP UKWN
INAC NO
ISAR NO
CPUB OFF
DAPC NO
BCOT 0
DSEL VOD
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 8015
TCPP NO
TARG 03
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
ANTK
SIGO STD
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3
NBS 2048
NBL 4096
TFD 0
DRNG NO
CDR NO


PAGE 002

MUS NO
RACD NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TTBL 0
ATAN NO
PLEV 2
ALRM NO
ART 0
SGRP 0
AACR NO

*********

REQ PRT

CUST 0

FEAT DSC

ESN009

FEAT CDP

TYPE DSC

DSC 3

DSC 3
FLEN 4
DSP DN
RLI 12
NPA
NXX

********

REQ PRT

CUST 0

FEAT RLB

RLI 12


RLI 12
ENTR 0
LTER NO
ROUT 6
TOD 0 ON 1 ON 2 ON 3 ON
4 ON 5 ON 6 ON 7 ON
CNV NO
EXP NO
FRL 0
DMI 0
FCI 0
FSNI 0
SBOC NRR
OHQ NO
CBQ NO

ISET 0
NALT 5
MFRL 0


***********


REQ prt

TYPE adan dch 15


ADAN DCH 15
CTYP MSDL
DNUM 11
PORT 1
DES CISCOTIE
USR PRI
DCHL 15
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC S100
SIDE NET
CNEG 1
RLS ID **
RCAP ND2
T200 3
T203 10
N200 3
N201 260
K 7


*********

YPE cequ


CEQU
MPED 8D
TERM
REMO
TERD
REMD
TERQ
REMQ
SUPL 004 020 V040
SUPC 008
SUPF
XCT 000 016
TDS * 000 * 016
CONF * 001 * 017
MFSD * 000 * 016

DLOP NUM DCH FRM LCMT YALM TRSH
PRI 012 24 ESF B8S FDL 00
013 24 ESF B8S FDL 00
014 24 ESF B8S FDL 00
015 24 ESF B8S FDL 00
018 24 ESF B8S FDL 00
019 24 ESF B8S FDL 00
EXT0 3PE
CNI 012 000 000
EXT1 3PE
CNI 012 000 000
MCFN S0B0 S0B1 S1B0 S1B1 S2B0 S2B1 S3B0 S3B1 FLSH TOTL
016 016 016 016 000 000 000 000 64 128


*****

and one of our trunks..

TYPE TNB
TN 15 1

DATE

PAGE

DES


DES CISCO
TN 015 01
TYPE TIE
CDEN SD
CUST 0
TRK PRI
PDCA 1
PCML MU
NCOS 6
RTMB 6 1
B-CHANNEL SIGNALING
TGAR 1
AST NO
IAPG 0
CLS UNR DIP CND WTA LPR APN THFD HKD
P10 VNL
TKID
DATE 1 SEP 2005

**********************

Any suggestions would be greatly appreciated!!

-bb1.

 

[johnpoole]

i get that err usually on dms interface because of the rls id being blank. my cisco interface is qsig and it runs clean. i would change TRMB YES to no, and check service msgs in ld 96, stat serv, they may need to be off, or enabled, just a miss match can cause a null msg.


john poole
bellsouth business
columbia,sc

 

[breakbuddy1]

i am able to make 4 digit calls from both the Nortel and Cisco sets but am not able to complete outside calls from the Cisco phones that pass through the Nortel.

Any suggestions?

I have changed

NET_DATA
FTOP to FTLY

and RDR_DATA to OPT CFO

any other suggestions?

thanks,
-bb1.

 

[johnpoole]

where does the call fail? your ncos on the tie is 6, i assume ncos 6 will allow the call. make sure the cisco is inserting the dial 9. enl msgi 15 in ld 96 and take a glance at the actual received digits, make sure the targ on the outbound trunks is not 3, i would change that route and targ x3.. i assume you know a targ to targ or targ to tgar blocks.. another thing i have had bite me, dsel vod, might try that vce

john poole
bellsouth business
columbia,sc

 

[ajnd]

change the cls on the trunk to dtn instead of dip

 

[johnpoole]

might be a great idea, never even noticed that one, good catch

john poole
bellsouth business
columbia,sc