Help needed with Avaya definity g3 si ds1 country protocol

[LineMann]

Hi everyone,
I want to connect my Unify Openscape 4000 with Avaya definity. I have set my Unify PRI setting with Master/ECMAV2/crc=y

DEV = S2COD PEN = 1-05-001-0 TGRP = 66 |
|---------------------------------------------------------------------------|
| PROTVAR = ECMAV2 INS = N SRCHMODE = ASC |
| COTNO = 43 COPNO = 43 DPLN = 0 |
| ITR = 1 COS = 40 LCOSV = 1 |
| LCOSD = 1 CCT = 66 DESTNO = 66 |
| SEGMENT = 1 DEDSCC = DEDSVC = NONE |
| FACILITY = DITIDX = SRTIDX = |
| TRTBL = GDTR SIDANI = N ATNTYP = CO |
| CBMATTR = NONE NWMUXTIM = 10 TCHARG = N |
| SUPPRESS = 0 DGTPR = CHIMAP = N |
| ISDNIP = ISDNNP = |
| PNPL2P = PNPL1P = PNPAC = |
| TRACOUNT = 10 SATCOUNT = MANY NNO = 1 -1 -166 |
| ALARMNO = 0 FIDX = 1 CARRIER = 1 |
| ZONE = EMPTY COTX = 43 FWDX = 5 |
| DOMTYPE = DOMAINNO = TPROFNO = |
| INIGHT = CCHDL = |
| UUSCCX = 16 UUSCCY = 8 FNIDX = 1 |
| CLASSMRK = EC & G711 & G729AOPT SRCGRP = ( ) |
| TCCID = SECLEVEL = TRADITIO |
| HMUSIC = 0 CALLTIM = 60 WARNTIM = 60 |
|---------------------------------------------------------------------------|
| BCNEG = N BCGR = 1 LWPAR = 25 |
| LWPP = 0 LWLT = 0 LWPS = 0 |
| LWR1 = 0 LWR2 = 0 |
| VNNO = |
| SVCDOM = |
| BCHAN = 1 && 30 |
|


+-----------------------------------------------------------------------+
| LOADWARE PARAMETERS CIRCUIT TYPE: DIUS2 SOURCEB BLOCK: 25 |
+-----------------------------------------------------------------------+
| LNTYPE = COPPER VERSION = S2 QUAL = ON |
| MASTER = Y DCHAN1 = 16 DCHAN2 = 0 |
| PATTERN = D5H QUAL1 = 10 SEC. QUAL2 = 10 MIN. |
| SMD = Y PERMACT = Y FCBAB = DFH |
| CDG = N FIXEDTEI = 0 CNTRNR = 255 |
| TEIVERIF = N CRC4REP = Y |
| DEV = INDEP |
| INFO = |
+-----------------------------------------------------------------------+


What should be the setting in Avaya ds1 to match the above parameter ?

DS1 CIRCUIT PACK

Location: 01A16 Name: xxxx
Bit Rate: 2.048 Line Coding: hdb3

Signaling Mode: isdn-pri
Connect: __????___ Interface: ___????_______
TN-C7 Long Timers? n Country Protocol: ???
Interworking Message: PROGress Protocol Version: ????
Interface Companding: alaw CRC? ????
Idle Code: 11111111
DCP/Analog Bearer Capability: 3.1kHz




Slip Detection? n Near-end CSU Type: other

Echo Cancellation? n

Please help

 

[biglebowski]

Does this help

https://www.tek-tips.com/viewthread.cfm?qid=1724081

 

[LineMann]

Sir-biglebowski (TechnicalUser)
Thanks for responding. The link shown did not solve the purpose. I want to know the protocol name corresponding country protocol number for Avaya.

 

[biglebowski]

Set it to the same as the OS4k, I don't think it matters unless you are connecting to the PSTN

I assume you are in europe (bit rate = 2048) then it will probably be "etsi" if not a number between 1 and 25

1 – United States (AT&T mode, also called 5ESS)
2 – Australia (Australia National PRI)
3 – Japan
4 – Italy
5 – Netherlands
6 – Singapore
7 – Mexico
8 – Belgium
9 – Saudi Arabia
10 – United Kingdom (ETSI)
11 – Spain
12 – France (ETSI)
13 – Germany (ETSI)
14 – Czech Republic
15 – Russia
16 – Argentina
17 – Greece
18 – China
19 – Hong Kong
20 – Thailand
21 – Macedonia
22 – Poland
23 – Brazil
24 – Nordic countries
25 – South Africa
etsi – ETSI (no use of RESTART message)
qsig – QSIG