Help....Backup Fail

[pyooi]

Hi, Everybody,

Have anybody face this problem?
The Backup is completed but the status is "Fail"
I'm using version 8.60

The Job Log as below




======================================================================
Job server: MPIWEBSVR
Job name: Full_Backup
Job started: July 30, 2003 at 10:00:05 PM
Job type: Backup
Job Log: BEX91.txt
======================================================================

Drive and media information from media mount:
Robotic Library Name:
Drive Name: SEAGATE 1
Slot: 0
Media GUID: {45C8292A-1A01-4145-ACEA-2C796AAC797F}
Media Label: 4MM000005
Overwrite Protection Time Left: None
Append Time Left: Infinite
Targeted Media Set Name: Media Set 1

======================================================================
Job Operation - Backup
Media operation - overwrite.
Hardware compression enabled.
======================================================================

Media Name: "Media created 30/07/2003 10:00:05 PM"
Backup of "D: New Volume"
Backup set #1 on storage media #1
Backup set description: "EWAS Full_Backup"
Backup Type: FULL - Back Up Files - Reset Archive Bit
Backup started on 30/07/2003 at 10:01:37 PM.
File "VDI.LOG" in use - Backed up.
The .DR file required for Intelligent Disaster Recovery is created/updated

Backup completed on 31/07/2003 at 1:24:35 AM.
Backed up 78250 files in 8059 directories.
1 file was in use
Processed 27,529,787,558 bytes in 3 hours, 22 minutes, and 58 seconds.
Throughput rate: 129.4 MB/min
----------------------------------------------------------------------
Unable to attach to MPIWEBSVR.
The item was not found.
^ ^ ^ ^ ^
Unable to attach to MPIWEBSVR.
^ ^ ^ ^ ^

======================================================================
Job Operation - Verify
======================================================================

Verify of "D: New Volume"
Backup set #1 on storage media #1
Backup set description: "EWAS Full_Backup"
Verify started on 31/07/2003 at 1:26:03 AM.

Verify completed on 31/07/2003 at 4:26:41 AM.
Verified 78250 files in 8059 directories.
0 files were different.
Processed 27,529,787,558 bytes in 3 hours, 0 minutes, and 38 seconds.
Throughput rate: 145.3 MB/min
----------------------------------------------------------------------

======================================================================
Job ended: July 31, 2003 at 4:26:41 AM
Job completion status: Failed
======================================================================


Thank you
Regards
pyooi

 

[craiga1027]

I have the same problem. My backup jobs will run and backup everything but the status is always failed. It will do this several days in a row, then it will run and be successful again without any changes. The only thing I do is clean the tape drive when it fails. I am able to restore data from jobs that failed everything seems to be there, but I sure would like to find out what makes it say that the job failed.

 

[wibbe]

Hi pyooi,

Here is youre reason from the logfile:

^ ^ ^ ^ ^
Unable to attach to MPIWEBSVR.
^ ^ ^ ^ ^

The backup server can not connect to MPIWEBSVR.
Some hints in youre trubleshooting:

- Ping MPIWEBSVR from the backup server. (using netbios name)
- Map networkdrive (\\MPIWEBSVR\c$) with BackupExec Service account.

// Wibbe

 

[wibbe]

Hi again,

OK, the backupserver is MPIWEBSVR.

Under selection, remove MPIWEBSVR under network and only use backup the local paths. You can not backup the local server over the network.

// Wibbe

 

[mattjurado]

And it shows there was an open file that it could not copy, but it did backup 78250 files in 8059 directories. Is this file count accurate for your data?


Matt J.