-
1
- #1
HiPath 4000 Version 3 Single Processor
NEW Hard Disk if possible.
Get ST340014A 40GB 7200 ATA/100 (Desktop Type)
or use Laptop Type MHW2060AT 40GB IDE with corresponding Compact Flash (CF) tray.
Use powered USB to SATA/IDE Combo Adapter Unit to plug in to laptop and hard disk
Go to Windows 7 computer management/disk management
Initialise the disk, then 'new simple volume'
No need to assign a drive letter.
Perform a quick format (NTFS or FAT) but then use
HP USB Disk Formatter to format the disk fully.
Open Hard Drive Image tool
Image to USB (Advanced)/Next
Directory - find the Folder V3.0_HDCF_Boot_Image and select
(the boot image needs to be downloaded and unzipped)
Click on 'select device' tab on hard drive image tool.
Ensure you select the correct drive to write to !
It should show up as ST340014A in the drop down list.
Click on Proceed/Yes
After a few minutes the 'OK' button will show and you can click on it.
Then at the main window click 'Cancel' to finish this part.
On the windows tray (near the clock) remove the 'bridge' safely.
Remove the disk and fit to a Hipath MO/HDD Tray ready for installing in a Hipath
Fitting is a reversal of removing - take photos if in any doubt beforehand.
You will need a Torx and Philips Screwdriver for to fit the HDD.
Fit Tray in Hipath with RTM on back and one processor in bottom.
Fit bypass SIM card in processor and LAN cable to your laptop from service or Atlantic Port
Fit RS232/V24 9 way 'D' type cable from Service to laptop also for Hyperterminal
Use 192.0.2.99 or similar on laptop.
Power up Hipath.
Wait for 'dash dot' on processor
TURN WINDOWS FIREWALL OFF
Open PCHI tool V213
In 'special/settings' Home Path C:/HiPath4000V30
SCSI & TCP/IP All ticked except CNU2
English and no verify
'Take Over'
Special/DSCXL Settings
Select Standard-DSCXL on left
Click on 'test' - result should be OK
Click on 'take over'
Click on Hicom-HD/HD->init
Wait and select TCP/IP 1-HD
Click V on top to change layout to be H4K V123 HD
Then on bottom ensure HD is selected and click OK/OK/OK
Wait
OK
Click on Hicom-HD
hd->restore
Wait and select TCP/IP 1-HD
Double click on P30252n4508B0004 in the middle
Click on Hard drive Init as well if not previously completed.
Click copy with UW7
then OK/OK
When completed
Click OK and Exit
TURN WINDOWS FIREWALL ON
Logon with Comwin root/hicom
EXE-REST:SYSTEM,RELOAD;
Wait for 'dash dot' again on boot up
Logon with Comwin root/hicom
CHA-FUNCT:REGIN=Y;
Click 'macro' / start CBL
Select Examples/SetTimeDate.cbl
Click 'macro'/retreive system variant
EXE-DBC:4000,3;
EXE-APC;
EXE-REST:SYSTEM,RELOAD;
Also log on with Hyperterminal or similar terminal program 9 way connector to Service port on bottom processor.
Use 38400 8N1NN settings
PRESS ESC TO STOP UNIX INSTALLING AT THIS STAGE
On dash dot logon with Comwin
CHA-FUNCT:REGIN=Y;
ADD-ANUM:LXXXXXXXXXXA;
DEL-HISTA;
ADD-HISTA:10000,DEACT;
CHA-CPCI:SYSCONF,YES,YES,NO
EXE-UPDAT:A1,ALL;
EXE-REST:SYSTEM,RELOAD;
Also log on with Hyperterminal or similar terminal program 9 way connector to Service port on bottom processor.
Use 38400 8N1NN settings
PRESS ESC TO STOP UNIX INSTALLING AT THIS STAGE
On reload log on with Comwin
CHA-FUNCT:REGIN=Y;
DIS-CODEW;
Get Hardware ID of SIM Card and get the relevant Codeword for it
It is date dependent so it might be out of date and you have to get an up to date one.
ADD-CODEW: SIM BYPASS CODEWORD;
Run in rest of ADS and all of SWU
(Edit the REGEN samtxt file to remove M1 1 and the M2 1 to make it easier)
Not all AMO's need to go back in - more information can be provided on this.
EXE-UPDAT:BP,ALL;
EXE-UPDAT:A1,ALL;
Now allow Unixware7 to install:
Also log on with Hyperterminal or similar terminal program 9 way connector to Service port on bottom processor.
Use 38400 8N1NN settings
ALLOW UNIX TO INSTALL - WAIT FOR
'Activation of ' (First) Installation' was successful.
If you have problems with Unix install try RESTART; in Comwin or try install again via the Unix/Hyperterminal menu.
I find that if I format the drive fully before setup it works.
If it does not work also try a different MO/HDD tray as it sometimes helps.
After Unix finished install go back to Comwin
ACT-USS:LTG;
You should get 'A' on the processor
Wait a few minutes for it to stabilize
EXE-UPDAT:BP,ALL;
EXE-UPDAT:A1,ALL;
Log on to UW7 using Virtual XP or a prepared for V3 Win 7 PC
Open browser 192.0.2.5
Do the 'client preparation' if not already done.
engr
Siemens2000
newpassword
newpassword
On main laptop
Open Filezilla FTP program or similar
Navigate to 192.0.2.5 engr/newpassword
Copy the latest dot tar file to /var/hf on the HiPath using the FTP program
On V3 it is ADP-V3.0_R5.0.34.tar
When transfer of tar file finished (approx 20 mins) exit the FTP program.
On Comwin
Open connection to HiPath
Click on file transfer (6th icon from left hand side)
Copy latest loadware to HiPath using the FJAM file transfer.
On V3 it is Spec_LW-V30-R8_4_4
Make sure the Loadware file is unzipped...
Drag the APSC folder from your loadware to the
DS: APSC folder and overwrite it.
Drag the APSP folder from your loadware to theDS: APSP folder and overwrite it.
(yes to all/ root/hicom)
When loadware transfers are finished disconnect the file transfer/HiPath
On Comwin
ADD-USER:EXAMPLE,0&&10,L&R&C&P&T&I,99,0;
Add in all your usernames.
Add in the passwords for each new username.
PASSW:EXAMPLE;
You can change the root/hicom password here as well if required.
EXE-UPDAT:A1,ALL;
On Browser:
Sofware Management/Software Transfer 2
On Left Hand Side open up RHF
Copy the V3.0 R8.4.27 patch packet to the HiPath
The Patch Packet should be unzipped when downloaded to the below directory structure.
(Path on your PC should be as follows:
C:\HiPath4000V30\hhd300\pp\p30252n4508bh2704)
Go to Software Management/Software Activation
New Activation
Select 'immediately' and 'notification of success/failure via maintenance alarm'
Click 'activate immediately'
27 patches will be installed until you see
(This screen will no longer be updated
because the activation is completed.)
Why it cannot be 'rolled up' to one patch I don't know...
Go to Software Management/Software Activation
Unix Hotfix Activation
Activate the previously transferred tar file
On occasion it will fail due to
Can not execute AMO DISP-DTSM:A1,HD;
If that happens go to Comwin
DEA-DSSM:A1,1;
ACT-DSSM:A1,1;
DISP-DTSM:A1,HD;
Go back and activate Unix hot fix again
If it fails again try a soft restart by typing in Capitals in Comwin
RESTART;
Then wait until Unix fully loads up again (Watch Hyperterminal)
Go back and activate hotfix again.
After the Unix update is installed you will have to wait until the Popup is clear.
It should say
Update is running. Be aware of your actions.
Next go to System Management/HiPath 4000 Administration
Click on 'search'
Click on 'object'
Fill in system number (REG-ANUM
Click web admin
Click Configuration Management
Click Customer Data Tab - fill in Customer Name
In Contract fill in Contract Number
11 222222 33333
In Configuration Management
Change Country to your prefix
Area Code
Get node code from DIS-ZAND:ALLDATA;
if not already correct
Click on save
Then go to the 'configuration management' tab
and click on 'upload'
This will enable you to use the configuration management
(It does UPLO2 to the Unixware from the RMX)
Go to Access Management/Account Management
Add a new user and password
Then go back to Access Management and Access Right Configuration
Give this new user all the access from the right hand side
(Drag over each item)
You now have another user instead of the default in case it gets locked out.
Go to Base Administration
Application Control
Add in 2 at a time what is required for the system.
By default you should add in
Dynamic Traffic Monitoring
Test Simulation Key Activity
Configuration Management
Hardware and Symptom Diagnosis
Real Time Diagnosis System
When finished 'refresh' the main page to show the changes
After that in Software Management you can add a backup schedule.
Ensure that any backup schedule you put in does not conflict with the CRON schedules in the RMX.
Then to finish add in the Customer LAN IP address, Subnet Mask, Gateway, Firewall entries and any NTP clock
in Base Administration/Unix Base Administration.
Sequence of loading of Hipath is Area E then Area J then MO/Compact Flash Card
To backup to Area J
Deactivate Area J on the Hard Disk
DEA-DSSM:A1,1,J;
Do a backup
EXE-UPDAT:BP,ALL;
EXE-UPDAT:A1,ALL;
COPY-DDRSM:A1,1,E,1,J,N;
Add in CRON commands to backup automatically for example:
ADD-CRON:1,P,0,5,*,*,*,"EXE-UPDAT:BP,ALL;";
ADD-CRON:2,P,10,5,*,*,*,"EXE-UPDAT:A1,ALL";
ADD-CRON:3,P,20,5,*,*,0,"COPY-DDRSM:A1,1,E&F,6,E&F,N;";
ADD-CRON:4,P,30,5,*,*,0,"COPY-DDRSM:A1,1,E,1,J,N;";
ADD-CRON:5,P,40,5,*,*,0,"STA-DEL:AS:VEGAS/DATEI;";
ADD-CRON:6,P,50,5,*,*,0,"STA-REGEN:AUTO,LxxxxxQxxxxA00001,N,,,,,,ALL;";
ADD-CRON:7,P,0,0,*,*,*,"DIS-ZAUSL:,Y;";
Finally shutting down.
EXE-UPDAT:BP,ALL;
EXE-UPDAT:A1,ALL;
DEA-DSSM:A1,1;
Power down
bring to customer site, change out Hard Disk tray and power up.
Log on to Comwin and change the CODEW to the customers one.
NEW Hard Disk if possible.
Get ST340014A 40GB 7200 ATA/100 (Desktop Type)
or use Laptop Type MHW2060AT 40GB IDE with corresponding Compact Flash (CF) tray.
Use powered USB to SATA/IDE Combo Adapter Unit to plug in to laptop and hard disk
Go to Windows 7 computer management/disk management
Initialise the disk, then 'new simple volume'
No need to assign a drive letter.
Perform a quick format (NTFS or FAT) but then use
HP USB Disk Formatter to format the disk fully.
Open Hard Drive Image tool
Image to USB (Advanced)/Next
Directory - find the Folder V3.0_HDCF_Boot_Image and select
(the boot image needs to be downloaded and unzipped)
Click on 'select device' tab on hard drive image tool.
Ensure you select the correct drive to write to !
It should show up as ST340014A in the drop down list.
Click on Proceed/Yes
After a few minutes the 'OK' button will show and you can click on it.
Then at the main window click 'Cancel' to finish this part.
On the windows tray (near the clock) remove the 'bridge' safely.
Remove the disk and fit to a Hipath MO/HDD Tray ready for installing in a Hipath
Fitting is a reversal of removing - take photos if in any doubt beforehand.
You will need a Torx and Philips Screwdriver for to fit the HDD.
Fit Tray in Hipath with RTM on back and one processor in bottom.
Fit bypass SIM card in processor and LAN cable to your laptop from service or Atlantic Port
Fit RS232/V24 9 way 'D' type cable from Service to laptop also for Hyperterminal
Use 192.0.2.99 or similar on laptop.
Power up Hipath.
Wait for 'dash dot' on processor
TURN WINDOWS FIREWALL OFF
Open PCHI tool V213
In 'special/settings' Home Path C:/HiPath4000V30
SCSI & TCP/IP All ticked except CNU2
English and no verify
'Take Over'
Special/DSCXL Settings
Select Standard-DSCXL on left
Click on 'test' - result should be OK
Click on 'take over'
Click on Hicom-HD/HD->init
Wait and select TCP/IP 1-HD
Click V on top to change layout to be H4K V123 HD
Then on bottom ensure HD is selected and click OK/OK/OK
Wait
OK
Click on Hicom-HD
hd->restore
Wait and select TCP/IP 1-HD
Double click on P30252n4508B0004 in the middle
Click on Hard drive Init as well if not previously completed.
Click copy with UW7
then OK/OK
When completed
Click OK and Exit
TURN WINDOWS FIREWALL ON
Logon with Comwin root/hicom
EXE-REST:SYSTEM,RELOAD;
Wait for 'dash dot' again on boot up
Logon with Comwin root/hicom
CHA-FUNCT:REGIN=Y;
Click 'macro' / start CBL
Select Examples/SetTimeDate.cbl
Click 'macro'/retreive system variant
EXE-DBC:4000,3;
EXE-APC;
EXE-REST:SYSTEM,RELOAD;
Also log on with Hyperterminal or similar terminal program 9 way connector to Service port on bottom processor.
Use 38400 8N1NN settings
PRESS ESC TO STOP UNIX INSTALLING AT THIS STAGE
On dash dot logon with Comwin
CHA-FUNCT:REGIN=Y;
ADD-ANUM:LXXXXXXXXXXA;
DEL-HISTA;
ADD-HISTA:10000,DEACT;
CHA-CPCI:SYSCONF,YES,YES,NO
EXE-UPDAT:A1,ALL;
EXE-REST:SYSTEM,RELOAD;
Also log on with Hyperterminal or similar terminal program 9 way connector to Service port on bottom processor.
Use 38400 8N1NN settings
PRESS ESC TO STOP UNIX INSTALLING AT THIS STAGE
On reload log on with Comwin
CHA-FUNCT:REGIN=Y;
DIS-CODEW;
Get Hardware ID of SIM Card and get the relevant Codeword for it
It is date dependent so it might be out of date and you have to get an up to date one.
ADD-CODEW: SIM BYPASS CODEWORD;
Run in rest of ADS and all of SWU
(Edit the REGEN samtxt file to remove M1 1 and the M2 1 to make it easier)
Not all AMO's need to go back in - more information can be provided on this.
EXE-UPDAT:BP,ALL;
EXE-UPDAT:A1,ALL;
Now allow Unixware7 to install:
Also log on with Hyperterminal or similar terminal program 9 way connector to Service port on bottom processor.
Use 38400 8N1NN settings
ALLOW UNIX TO INSTALL - WAIT FOR
'Activation of ' (First) Installation' was successful.
If you have problems with Unix install try RESTART; in Comwin or try install again via the Unix/Hyperterminal menu.
I find that if I format the drive fully before setup it works.
If it does not work also try a different MO/HDD tray as it sometimes helps.
After Unix finished install go back to Comwin
ACT-USS:LTG;
You should get 'A' on the processor
Wait a few minutes for it to stabilize
EXE-UPDAT:BP,ALL;
EXE-UPDAT:A1,ALL;
Log on to UW7 using Virtual XP or a prepared for V3 Win 7 PC
Open browser 192.0.2.5
Do the 'client preparation' if not already done.
engr
Siemens2000
newpassword
newpassword
On main laptop
Open Filezilla FTP program or similar
Navigate to 192.0.2.5 engr/newpassword
Copy the latest dot tar file to /var/hf on the HiPath using the FTP program
On V3 it is ADP-V3.0_R5.0.34.tar
When transfer of tar file finished (approx 20 mins) exit the FTP program.
On Comwin
Open connection to HiPath
Click on file transfer (6th icon from left hand side)
Copy latest loadware to HiPath using the FJAM file transfer.
On V3 it is Spec_LW-V30-R8_4_4
Make sure the Loadware file is unzipped...
Drag the APSC folder from your loadware to the
DS: APSC folder and overwrite it.Drag the APSP folder from your loadware to the
DS: APSP folder and overwrite it.(yes to all/ root/hicom)
When loadware transfers are finished disconnect the file transfer/HiPath
On Comwin
ADD-USER:EXAMPLE,0&&10,L&R&C&P&T&I,99,0;
Add in all your usernames.
Add in the passwords for each new username.
PASSW:EXAMPLE;
You can change the root/hicom password here as well if required.
EXE-UPDAT:A1,ALL;
On Browser:
Sofware Management/Software Transfer 2
On Left Hand Side open up RHF
Copy the V3.0 R8.4.27 patch packet to the HiPath
The Patch Packet should be unzipped when downloaded to the below directory structure.
(Path on your PC should be as follows:
C:\HiPath4000V30\hhd300\pp\p30252n4508bh2704)
Go to Software Management/Software Activation
New Activation
Select 'immediately' and 'notification of success/failure via maintenance alarm'
Click 'activate immediately'
27 patches will be installed until you see
(This screen will no longer be updated
because the activation is completed.)
Why it cannot be 'rolled up' to one patch I don't know...
Go to Software Management/Software Activation
Unix Hotfix Activation
Activate the previously transferred tar file
On occasion it will fail due to
Can not execute AMO DISP-DTSM:A1,HD;
If that happens go to Comwin
DEA-DSSM:A1,1;
ACT-DSSM:A1,1;
DISP-DTSM:A1,HD;
Go back and activate Unix hot fix again
If it fails again try a soft restart by typing in Capitals in Comwin
RESTART;
Then wait until Unix fully loads up again (Watch Hyperterminal)
Go back and activate hotfix again.
After the Unix update is installed you will have to wait until the Popup is clear.
It should say
Update is running. Be aware of your actions.
Next go to System Management/HiPath 4000 Administration
Click on 'search'
Click on 'object'
Fill in system number (REG-ANUM
Click web admin
Click Configuration Management
Click Customer Data Tab - fill in Customer Name
In Contract fill in Contract Number
11 222222 33333
In Configuration Management
Change Country to your prefix
Area Code
Get node code from DIS-ZAND:ALLDATA;
if not already correct
Click on save
Then go to the 'configuration management' tab
and click on 'upload'
This will enable you to use the configuration management
(It does UPLO2 to the Unixware from the RMX)
Go to Access Management/Account Management
Add a new user and password
Then go back to Access Management and Access Right Configuration
Give this new user all the access from the right hand side
(Drag over each item)
You now have another user instead of the default in case it gets locked out.
Go to Base Administration
Application Control
Add in 2 at a time what is required for the system.
By default you should add in
Dynamic Traffic Monitoring
Test Simulation Key Activity
Configuration Management
Hardware and Symptom Diagnosis
Real Time Diagnosis System
When finished 'refresh' the main page to show the changes
After that in Software Management you can add a backup schedule.
Ensure that any backup schedule you put in does not conflict with the CRON schedules in the RMX.
Then to finish add in the Customer LAN IP address, Subnet Mask, Gateway, Firewall entries and any NTP clock
in Base Administration/Unix Base Administration.
Sequence of loading of Hipath is Area E then Area J then MO/Compact Flash Card
To backup to Area J
Deactivate Area J on the Hard Disk
DEA-DSSM:A1,1,J;
Do a backup
EXE-UPDAT:BP,ALL;
EXE-UPDAT:A1,ALL;
COPY-DDRSM:A1,1,E,1,J,N;
Add in CRON commands to backup automatically for example:
ADD-CRON:1,P,0,5,*,*,*,"EXE-UPDAT:BP,ALL;";
ADD-CRON:2,P,10,5,*,*,*,"EXE-UPDAT:A1,ALL";
ADD-CRON:3,P,20,5,*,*,0,"COPY-DDRSM:A1,1,E&F,6,E&F,N;";
ADD-CRON:4,P,30,5,*,*,0,"COPY-DDRSM:A1,1,E,1,J,N;";
ADD-CRON:5,P,40,5,*,*,0,"STA-DEL:
AS:VEGAS/DATEI;";ADD-CRON:6,P,50,5,*,*,0,"STA-REGEN:AUTO,LxxxxxQxxxxA00001,N,,,,,,ALL;";
ADD-CRON:7,P,0,0,*,*,*,"DIS-ZAUSL:,Y;";
Finally shutting down.
EXE-UPDAT:BP,ALL;
EXE-UPDAT:A1,ALL;
DEA-DSSM:A1,1;
Power down
bring to customer site, change out Hard Disk tray and power up.
Log on to Comwin and change the CODEW to the customers one.
![[bigsmile]](/data/assets/smilies/bigsmile.gif "[bigsmile] [bigsmile]")
![[sad]](/data/assets/smilies/sad.gif "[sad] [sad]")
I do not have access right to SEBA, I use HD CLONE to copy disk without codeword at now,but I have no by pass SIM card,and if I use any customer SIM card add codew date late than the customer I want input ADS data,I don't can add-codew any more, so it take me long time at customer site to input REGEN file.