H.323 Gateway not registering in CCM4.1.2 1

[kam72]

After configuring the router i have add the device as a H.323 gatway CCM deducted IP address of Router but Registration is :UNKNOWN.

If anyone configured h.323 gateway in CCM4.1.2 please send me the information.
============================================================
CISCO ROUTER 2620 CONFIGURATION
============================================================
service timestamps debug uptime
service timestamps log uptime
hostname nafay
ip subnet-zero
call rsvp-sync
voice class h323 1
h225 timeout tcp establish 3
interface FastEthernet0/0
ip address 192.168.0.55 255.255.255.0
duplex auto
speed auto
interface Serial0/0
no ip address
shutdown
ip classless
ip http server
voice-port 1/0/0
voice-port 1/0/1
voice-port 1/1/0
voice-port 1/1/1
dial-peer cor custom
dial-peer voice 100 voip
preference 1
destination-pattern 1...
voice-class h323 1
session target ipv4:192.168.0.111
dtmf-relay h245-alphanumeric
ip precedence 5
dial-peer voice 101 voip
preference 2
destination-pattern 1...
session target ipv4:192.168.0.111
dtmf-relay h245-alphanumeric
ip precedence 5
line con 0
line aux 0
line vty 0 4
============================================================
SHOW VERSION
============================================================
nafay#sh ver
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-JS-M), Version 12.2(31), RELEASE SOFTWARE (fc2)
Technical Support:

http://www.cisco.com/techsupport

Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Thu 11-Aug-05 17:24 by tinhuang
Image text-base: 0x8000808C, data-base: 0x814710D8

ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
ROM: C2600 Software (C2600-JS-M), Version 12.2(31), RELEASE SOFTWARE (fc2)

nafay uptime is 3 minutes
System returned to ROM by power-on
System image file is "flash:c2600-js-mz.122-31.bin"

cisco 2620 (MPC860) processor (revision 0x102) with 61440K/4096K bytes of memory
.
Processor board ID JAD042701EE (1286926306)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
1 FastEthernet/IEEE 802.3 interface(s)
1 Serial network interface(s)
4 Voice FXO interface(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

nafay#
============================================================
Thanks

 

[hunterdw]

What you are experiencing is normal. All of my H323 gateways show unknown. As do any H323 gateways I've ever seen on CCM 3.x, 4.x and 4.1.x in my network or anyone elses network.

What were you expecting to see?

Not being an arse, but I'm unclear or what you expected?

 

[kam72]

Unable to make and receive calls

 

[rtfmdude]

kam72,

h323 gateways do not register.

 

[kam72]

Unable to make and receive calls

 

[rtfmdude]

Is your callmanager still stopping for no reason?

 

[kam72]

Yes I tried my best it starting but after few second automatically stopping and IPPhones is keep on displaying registering............

Eventually i spent 9 hours, formatted the pc and reinstalled the CCM4.1.2 now all the phones are registered working back on h.323
============================================================
Unable to make and receive call through Ip Phone
============================================================
Here is the Show Diag
============================================================
nafay#show diag
Slot 0:
C2620 1FE Mainboard Port adapter, 2 ports
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware Revision : 1.2
PCB Serial Number : JAD042701EE (1286926306)
Part Number : 73-2843-07
RMA History : 00
RMA Number : 0-0-0-0
Board Revision : B0
Deviation Number : 0-0
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 00 94 41 01 02 C1 18 4A 41 44 30 34 32
0x10: 37 30 31 45 45 20 28 31 32 38 36 39 32 36 33 30
0x20: 36 29 82 49 0B 1B 07 04 00 81 00 00 00 00 42 42
0x30: 30 80 00 00 00 00 FF FF FF FF FF FF FF FF FF FF
0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

WIC Slot 0:
Serial 1T WAN daughter card
Hardware revision 1.0 Board revision J0
Serial number 19828317 Part number 800-01514-01
Test history 0x0 RMA number 00-00-00
Connector type Wan Module
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 02 01 00 01 2E 8E 5D 50 05 EA 01 00 00 00 00
0x30: 98 00 00 00 00 06 02 01 FF FF FF FF FF FF FF FF

Slot 1:
4 PORT Voice PM for C2600 Port adapter
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware revision 1.1 Board revision K0
Serial number 27332468 Part number 800-02491-02
FRU Part Number: NM-2V=

Test history 0x0 RMA number 00-00-00
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 65 01 01 01 A1 0F 74 50 09 BB 02 00 00 00 00
0x30: A0 00 00 00 02 03 20 17 FF FF FF FF FF FF FF FF

VIC Slot 0:
FXO Voice daughter card (2 port)
Hardware revision 1.1 Board revision K0
Serial number 27583475 Part number 800-02495-01
Test history 0x0 RMA number 00-00-00
Connector type Wan Module
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 0D 01 01 01 A4 E3 F3 50 09 BF 01 00 00 00 00
0x30: A0 00 00 00 02 05 08 01 FF FF FF FF FF FF FF FF

VIC Slot 1:
FXO Voice daughter card (2 port)
Hardware revision 1.1 Board revision K0
Serial number 27583515 Part number 800-02495-01
Test history 0x0 RMA number 00-00-00
Connector type Wan Module
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 0D 01 01 01 A4 E4 1B 50 09 BF 01 00 00 00 00
0x30: A0 00 00 00 02 05 08 01 FF FF FF FF FF FF FF FF
nafay#

====================================================
Here is Sh Ver
====================================================
nafay#sh version
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-JS-M), Version 12.2(31), RELEASE SOFTWARE (fc2)
Technical Support:

http://www.cisco.com/techsupport

Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Thu 11-Aug-05 17:24 by tinhuang
Image text-base: 0x8000808C, data-base: 0x814710D8

ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
ROM: C2600 Software (C2600-JS-M), Version 12.2(31), RELEASE SOFTWARE (fc2)

nafay uptime is 12 hours, 0 minutes
System returned to ROM by power-on
System image file is "flash:c2600-js-mz.122-31.bin"

cisco 2620 (MPC860) processor (revision 0x102) with 61440K/4096K bytes of memory
.
Processor board ID JAD042701EE (1286926306)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
1 FastEthernet/IEEE 802.3 interface(s)
1 Serial network interface(s)
4 Voice FXO interface(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102
nafay#
============================================================
Here is the Sh Run
============================================================
nafay#sh run
Building configuration...

Current configuration : 1031 bytes
!
version 12.2
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname nafay
!
ip subnet-zero
!
call rsvp-sync
!
voice class h323 1
h225 timeout tcp establish 3
!
interface FastEthernet0/0
ip address 192.168.0.55 255.255.255.0
duplex auto
speed auto
!
interface Serial0/0
no ip address
shutdown
!
ip classless
ip http server
!
voice-port 1/0/0
!
voice-port 1/0/1
!
voice-port 1/1/0
!
voice-port 1/1/1
!
dial-peer cor custom
!
dial-peer voice 100 voip
preference 1
destination-pattern 1...
voice-class h323 1
session target ipv4:192.168.0.111
dtmf-relay h245-alphanumeric
ip precedence 5
!
dial-peer voice 101 voip
preference 2
destination-pattern 1...
session target ipv4:192.168.0.111
dtmf-relay h245-alphanumeric
ip precedence 5
!
dial-peer voice 200 pots
preference 1
destination-pattern 9T
port 1/0/0
!
dial-peer voice 201 pots
preference 2
destination-pattern 9T
port 1/0/1
!
line con 0
line aux 0
line vty 0 4
login
end
nafay#

 

[rtfmdude]

configs look ok, don't notice any problem. I suggest you run a 'debug voip ccapi inout' 'debug vpm signal' and 'debug h225 asn1,' then try to send a call to callmanager, or vice versa. you may want to zip it and post it on an ftp server somewhere.

 

[mishkanyc]

well first of all make sure that you have this command under the interface:
"h323-gateway voip bind srcaddr 10.200.135.249"

also once you do that reset it in ccm
the state should say uknown but it should still show the address of the router

 

[kam72]

thanks for the reply

"h323-gateway voip bind srcaddr 10.200.135.249"

Is 10.200.135.249 is the IP address of CCM?

 

[rtfmdude]

No, it should be an ip address on the gateway that is reachable by callmanager. It's a way to 'bind' all h323 signaling and media traffic to a specific ip address.

 

[kam72]

I did but still same problem. From my mobile i am ringing on pstn number when iring on number i can hear bell ring once then engage tone on my mobile.

When i press 9 i am getting dial tone on IP Phone after dial tone when i dial the number it not dialling.

Thanks

 

[rtfmdude]

try running some debugs:

I suggest you run a 'debug voip ccapi inout' 'debug vpm signal' and 'debug h225 asn1,' then try to send a call to callmanager, or vice versa. you may want to zip it and post it on an ftp server somewhere.

 

[mishkanyc]

h323-gateway voip bind srcaddr 10.200.135.249" in this command the ip address is the IP address of the interface under which the command is actually applied.
Lets say if the interface connected to teh network and CCM is fa0/0 IP address is 192.168.1.1 the the command would look
!
interface fast ethernet 0/0
"h323-gateway voip bind srcaddr 192.168.1.1"
!

Next if you call from a fone to your router and after a ring you get a dial tone that means your dial-peers are not configured correctly! or the signal is not terminated end to end
What kind of PSTN do you have going into the router? FXO or PRI? if tis PRI with DID it means your dial-peer that matches incoming calls needs to have "direct-inward-dial" command in the dial-peer