memphistim
MIS
I have a G350 connected to an S8730 running 5.0.1 that uses a PRI T1 using protocol "c"...not "a" for custom or "b" for National.
The PRI T1 will work when the gateway is registered, but will not work when the G350 goes into SLS mode.
I have read the chapter on G250/G350 SLS and followed what I see for setting up the DS1, Trunk, Signal Group and Dial Pattern, but I can't seem to see why this isn't working.
I do have clock sync set on the G350 as well.
Does anyone have a working SLS config with PRI T1 that they can share?
Here is what I am showing...
Buffalo-G350-SLS(super-sls)# show ds1
DS1 Rate Signaling Chan Connect Interface Side Protocol Ver Bearer Cmpd Ltm
--- ---- --------- ----- -------- ---------- ---- --------- --- ------ ---- ---
v3 1544 isdnpri tslot network network a country1 c 3khz ulaw no
Name = Buffalo
Group Type Dial Tac Supervision Treat Insert
----- ------------ ------ ---- ----------------- ------- ------
160 t1-isdn dtmf #16 - blank
Name=Buffalo
Ports=v301:160,v302:160,v303:160,v304:160,v305:160,v306:160,v307:160,v308:160,v3
09:160
,v310:160,v311:160,v312:160,v313:160,v314:160,v315:160,v316:160,v317:160
,v318:160,v319:160,v320:160,v321:160,v322:160,v323:160
Codeset Codeset Channel Digit Japan
Display National Preference Handling Discon
-------- -------- ---------- --------------- ------
codeset6 codeset6 preferred enbloc-enbloc no
Send Name Send Number Number Format Trunk Hunt
--------- ----------- ------------- ----------
yes yes public descend
Cbc Cbc-service-feature Cbc-parameter
--- ------------------- -------------
no - -
Buffalo-G350-SLS(super-sls)# show sig
Sig-Group Tg-Select Assoc-sig Prime-DChan Nfas-Module/Nfas-Ids
--------- --------- --------- ----------- -------------------------------------
160 160 yes 016v324
Buffalo-G350-SLS(super-sls)# show dial
Dial-String/Deny Min/Max Type Trunk Delete/Insert
Length Group Digits
-------------------- ------- ---- ----- ---------------------------------------
1/n 11/11 fnpa 160 0/-
11/n 2/2 emer 160 0/9
2/n 7/7 locl 160 0/-
3/n 7/7 locl 160 0/-
4/n 7/7 locl 160 0/-
5/n 7/7 locl 160 0/-
6/n 7/7 locl 160 0/-
7/n 10/10 hnpa 160 0/-
8/n 7/7 locl 160 0/-
9/n 3/3 emer 160 0/-
The PRI T1 will work when the gateway is registered, but will not work when the G350 goes into SLS mode.
I have read the chapter on G250/G350 SLS and followed what I see for setting up the DS1, Trunk, Signal Group and Dial Pattern, but I can't seem to see why this isn't working.
I do have clock sync set on the G350 as well.
Does anyone have a working SLS config with PRI T1 that they can share?
Here is what I am showing...
Buffalo-G350-SLS(super-sls)# show ds1
DS1 Rate Signaling Chan Connect Interface Side Protocol Ver Bearer Cmpd Ltm
--- ---- --------- ----- -------- ---------- ---- --------- --- ------ ---- ---
v3 1544 isdnpri tslot network network a country1 c 3khz ulaw no
Name = Buffalo
Group Type Dial Tac Supervision Treat Insert
----- ------------ ------ ---- ----------------- ------- ------
160 t1-isdn dtmf #16 - blank
Name=Buffalo
Ports=v301:160,v302:160,v303:160,v304:160,v305:160,v306:160,v307:160,v308:160,v3
09:160
,v310:160,v311:160,v312:160,v313:160,v314:160,v315:160,v316:160,v317:160
,v318:160,v319:160,v320:160,v321:160,v322:160,v323:160
Codeset Codeset Channel Digit Japan
Display National Preference Handling Discon
-------- -------- ---------- --------------- ------
codeset6 codeset6 preferred enbloc-enbloc no
Send Name Send Number Number Format Trunk Hunt
--------- ----------- ------------- ----------
yes yes public descend
Cbc Cbc-service-feature Cbc-parameter
--- ------------------- -------------
no - -
Buffalo-G350-SLS(super-sls)# show sig
Sig-Group Tg-Select Assoc-sig Prime-DChan Nfas-Module/Nfas-Ids
--------- --------- --------- ----------- -------------------------------------
160 160 yes 016v324
Buffalo-G350-SLS(super-sls)# show dial
Dial-String/Deny Min/Max Type Trunk Delete/Insert
Length Group Digits
-------------------- ------- ---- ----- ---------------------------------------
1/n 11/11 fnpa 160 0/-
11/n 2/2 emer 160 0/9
2/n 7/7 locl 160 0/-
3/n 7/7 locl 160 0/-
4/n 7/7 locl 160 0/-
5/n 7/7 locl 160 0/-
6/n 7/7 locl 160 0/-
7/n 10/10 hnpa 160 0/-
8/n 7/7 locl 160 0/-
9/n 3/3 emer 160 0/-