FXS card not registered

[nabs79]

Hi,

I have one CCM 4.1.3 and gateways 2801 in other sites with FXS cards for the fax.
Sometimes i have problems with the fax and i have the FXS card not registered in the CCM.
I make no mgcp and mgcp on trhe gateway in order to fix that.

Do you know why i have this recurrent problem?

Thanks

 

[whykap]

can you post your mgcp config on the router?
What version of IOS?

 

[nabs79]

I have one with IOS version 2.43f and another with 2.411
Below some of the config of the gateway


interface BRI0/1/0
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn bind-l3 ccm-manager service mgcp
isdn send-alerting
!
interface BRI0/1/1
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn bind-l3 ccm-manager service mgcp
isdn send-alerting
!
ip default-gateway 172.16.40.254
ip route 0.0.0.0 0.0.0.0 172.16.40.254
!
!
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
!
!
!
!
control-plane
!
!
!
voice-port 0/0/0
cptone FR
!
voice-port 0/0/1
!
voice-port 0/1/0
compand-type a-law
cptone FR
!
voice-port 0/1/1
compand-type a-law
cptone FR
!
voice-port 0/2/0
cptone FR
!
voice-port 0/2/1
!
ccm-manager fallback-mgcp
ccm-manager mgcp
no ccm-manager fax protocol cisco
ccm-manager music-on-hold
ccm-manager config server 172.16.253.252
ccm-manager config
!
mgcp
mgcp call-agent 172.16.253.252 2427 service-type mgcp version 0.1
mgcp dtmf-relay voip codec all mode out-of-band
mgcp rtp unreachable timeout 1000 action notify
mgcp modem passthrough voip mode nse
mgcp package-capability rtp-package
no mgcp package-capability res-package
mgcp package-capability sst-package
no mgcp package-capability fxr-package
mgcp package-capability pre-package
no mgcp timer receive-rtcp
mgcp sdp simple
mgcp fax t38 inhibit
mgcp rtp payload-type g726r16 static
mgcp bind control source-interface FastEthernet0/0
mgcp bind media source-interface FastEthernet0/0
!
mgcp profile default
!
!
!
dial-peer voice 10 pots
description APPELS SRST SORTANTS 10 CHIFFRES
translation-profile outgoing Outgo_TeteLigne-NumAb
destination-pattern 0..........
progress_ind setup enable 0
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
fax rate disable
direct-inward-dial
port 0/1/0
!
dial-peer voice 11 pots
description APPELS SRST SORTANTS TS APPELS
translation-profile incoming Inco_Prefix-ModSDA
translation-profile outgoing Outgo_TeteLigne-NumAb
destination-pattern 0T
progress_ind setup enable 0
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
fax rate disable
direct-inward-dial
port 0/1/0
!
dial-peer voice 999000 pots
service mgcpapp
port 0/0/0
!
dial-peer voice 999020 pots
service mgcpapp
port 0/2/0
!
dial-peer voice 14 pots
description APPELS SRST SORTANTS 10 CHIFFRES
translation-profile outgoing Outgo_TeteLigne-NumAb
destination-pattern 0..........
progress_ind setup enable 0
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
fax rate disable
direct-inward-dial
port 0/1/1
!
dial-peer voice 15 pots
description APPELS SRST SORTANTS TS APPELS
translation-profile incoming Inco_Prefix-ModSDA
translation-profile outgoing Outgo_TeteLigne-NumAb
destination-pattern 0T
progress_ind setup enable 0
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
fax rate disable
direct-inward-dial
port 0/1/1
!
!
no dial-peer outbound status-check pots
gateway
timer receive-rtp 600


Thanks

 

[whykap]

So it is registering with 172.16.253.252 which is your pub I assume since that is where you are pointing it to get the MGCP config file also.
In your ccm gateway config where does it show the gateway being registered? make sure it is the same server. Otherwise you will have issues.
let us know.

 

[nabs79]

The problem was from the version of the IOS.
I put the version 2.411