FXO Config Help

[PWRMAD]

Hi

I have a 2610XM (C2600-SPSERVICESK9-M), Version 12.4(9)T7 with CCME Version 4.0(0, I have configured 3 test phones a 7960, 7940, & 7905 and each phone is able to call between each other. However none of the phones can make outgoing calls but can receive them in a limited fashion. If I make a test call into the router the FXO card answers the call and provides me a new dial tone then I have to dial an extension number and then the phone rings and I can now talk. This acts like a DID interface but I am not sure what I have done wrong the FXO card part number is VIC-FXO-M1 any ideas?

I have listed the config below

Thanks


CCME#sh run
Building configuration...

Current configuration : 2252 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname CCME
!
boot-start-marker
boot-end-marker
!
no aaa new-model
!
resource policy
!
no network-clock-participate slot 1
no network-clock-participate wic 0
ip cef
!
no ip dhcp use vrf connected
!
ip dhcp pool DHCP1
network 10.1.10.0 255.255.255.0
default-router 10.1.10.1
option 150 ip 10.1.10.1
!
interface Port-channel1
!
interface FastEthernet0/0
ip address 10.1.10.1 255.255.255.0
duplex auto
speed auto
!
ip http server
no ip http secure-server
!
tftp-server flash:/phone/7940-7960/P0030702T023.loads alias P0030702T023.loads
tftp-server flash:/phone/7940-7960/P0030702T023.sb2 alias P0030702T023.sb2
tftp-server flash:/phone/7940-7960/P0030702T023.sbn alias P0030702T023.sbn
tftp-server flash:/phone/7905/CP7905080001SCCP051117A.sbin alias CP7905080001SCC
P051117A.sbin
tftp-server flash:/phone/7905/CP7905080001SCCP051117A.zup alias CP7905080001SCCP
051117A.zup
!
control-plane
!
voice-port 1/0/0
caller-id enable
!
voice-port 1/0/1
caller-id enable
!
dial-peer voice 1 pots
incoming called-number 15[12]
port 1/0/1
!
telephony-service
load 7960-7940 P0030702T023
load 7905 CP7905080001SCCP051117A
max-ephones 24
max-dn 24
ip source-address 10.1.10.1 port 2000
system message Hello
max-conferences 8 gain -6
moh music-on-hold.au
web admin system name admin password tech
web admin customer name tech password tech
dn-webedit
transfer-system full-consult
secondary-dialtone 9
create cnf-files version-stamp Jan 01 2002 00:00:00
!
ephone-dn 10 dual-line
number 1510
label 555-1510
name 7960
!
ephone-dn 11 dual-line
number 1511
label 555-1511
name 1511
!
ephone-dn 15 dual-line
number 1515
label 1515
name 1515
!
ephone 10
mac-address 0008.218C.05A7
username "phone" password 1234
type 7960
auto-line incoming
button 1:10 2:15
!
ephone 11
mac-address 0008.A3D3.17C9
username "1511" password 1234
type 7905
button 1:11
!
ephone 15
mac-address 001A.2F80.36F4
type 7940
auto-line incoming
button 1:10 2:15
!
line con 0
line aux 0
line vty 0 4
login
!
end

 

[whykap]

under the voice-port enter
connection plar xxxx

where xxxx is the DN you want the fxo port to ring.

for example
connection plar 1510

 

[pndscm]

Sometimes the 'connection plar XXXX' causes an issue where the caller heres a couple ringbacks before the phone actually rings. If this happens, try 'connection plar opx XXXX'

 

[PWRMAD]

Thanks for the help, yes the intension is to have 2 line buttons on each 7960 active ie line 1 = button 1 and line 2 = button 2. Is it the ephone-dn where I can configure the lines to a specific phone?

Thanks

 

[PWRMAD]

Just as a foot note that did get a specific line to a specific extension but I need to assign lines to buttons can you help me with that please.

Thanks

 

[whykap]

You can't assign an FXO line to phone by making it appear on the phone. You plar the line to the DN of the phone, as I instructed earlier, which has the same outcome.
What exactly are you trying to do that the connection plar did not do?

 

[PWRMAD]

Well I guess I am thinking of a more conventional business PBX and for example on a 7960 I have 6 side buttons and I would like to have button 1 assigned to line 1 and so on. I would also like to duplicate this on each extension with a few exceptions such as a 7940 and since it has 2 buttons I would like to assign 2 lines. I am sure it is something I am not doing corectly but when I made the changes you suggested the line did ring into 1 extension and it will not accept multiple entries. So I am stuck again, the caller ID did work and the call was fine but just on 1 phone.

Thanks for your kind help.
Randy