Fujitsu Pabx SMDR 1

[sthcoast]

I have put in an old Telecom 9600 to get a client out of trouble until he completes his development. Programmed up OK but not getting anything from the SMDR. System has PSTN lines. Does it need exchange pulses in order to for the SMDR to operate?

Not getting a thing out of the port but can configure it as programming port and it works.
Thanks
South Coast

 

[telm59]

dis you ass ap,smdr,dcuxx.

 

[sthcoast]

Thanks for the advice, could you type it again, I think you must be a doctor!!!!

 

[ksphoneman]

Pins needed in the DB25 RS232 cable, 2,4,5,6,7,8,20
DTR must be on to keep the port active when the PBX is attempting to transmit data.

Type 35 cable is for DTE (MC)
Type 36 cable is for DCE (Modem)

DCC Port Assignment ASS DCCPT, DEL DCCPT, DIS DCCPT, ASS AP, DEL AP, DIS AP
Format 1: For SMDR printer
ASS DCCPT,<DCU no.>,PRT,TTY,(bps)
<DCU no.> = DCU01
/ = DCU02
/ = DCU03
/ = DCU11
/ = DCU12
/ = DCU13
/ = DCU20
/ = DCU21
/ = DCU22
/ = DCU23
/ = DCU30
/ = DCU31
/ = DCU32
/ = DCU33,
(bps)> = 300
/ = 1200
/ = 2400
/ = 4800
/ = 9600
/ = 19200]
NOTE: After entering the ASS DCCPT command, be sure to enter
the ASS AP command, as shown on the next page.

ASS AP,SMDR,<DCU no.> (Same port as previous)

Place the DCC port in an in-service state if the Call Accounting AP or the SMDR printer has been installed and is functioning properly.
Format:
RES IO,<DCU no.>

Dialed / Outpulsed Number on SMDR / SMDA Record
CHA SVP, DIS SVP
Format:
CHA SVP,2,15,
<service data> = 00 (record outpulsed number)
/ = 01 (record dialed number)
Dialed Number Masking Digits Length
CHA SVP, DIS SVP
Format:
CHA SVP,2,3,<service data> = 00 (no masking)
/ = 01 to 14 (1 to 20 digits masked)
SMDR / SMDA Facility Access Code Output
CHA SVP, DIS SVP
Format:
CHA SVP,2,88,<service data> = 00 (display speed calling
access code)
/ = 01 (display trunk or ARS access code)
ISDN ANI Output to Incoming Call Record
CHA SVP, DIS SVP
Format:
CHA SVP,2,118,<service data> = 00 (not provided)
/ = 01 (provided)
Type of Call Record for AAR Call to Own PBX
CHA SVP, DIS SVP
Format:
CHA SVP,2,119,<service data> = 00 (outgoing call record)
/ = 01 (incoming call record)
Outgoing Trunk Information CHA SVP, DIS SVP
Format:
CHA SVP,2,123,<service data> = 00 (EN)
/ = 01 (TGN)
Incoming Trunk Information CHA SVP, DIS SVP
Format:
CHA SVP,2,124,<service data> = 00 (EN)
/ = 01 (TGN)
Type of Calling Number on SMDR/SMDA Record
CHA SVP, DIS SVP
Format:
CHA SVP,2,198,<service data> = 00 (5 digits (DN)
/ = 01 (7 digits (ISSLC+DN))
PBX Identification CHA SVP, DIS SVP
Format:
CHA SVP,2,199,<service data> = 0 to 255
Type of SMDR Field for Incoming, Outgoing, Data Call
Records
CHA SVP, DIS SVP
Format:
CHA SVP,2,227<service data> = 0 (HH:MM (default))
CHA SVP,2,227<service data> = 1 (DD/MM/YYYY.HH:MM.SS)
Spec: Fields
Incoming = Time of Incoming Seizure
Outgoing = Origination Time
Data = Call Start Time
SMDR Column Length CHA SVP, DIS SVP
Format:
CHA SVP,2,227 <service data> = 0 (132 Cols. (default))
CHA SVP,2,227 <service data> = 1 (152 Cols.)
Internal Station to Station Output on SMDR
CHA SVP, DIS SVP
Format:
CHA SVP,2,262,<service data> = 00 (not provided) / = 01 (provided)