I'm trying to program a hot line that dials an access code, that for a system that will dial a 1800 number. The access code is for a PRI that has the channels cls DTN. The 500 has also cls DTN, but if I use my test phone, it only work in DIP (pulse). What I'm missing???
Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations Rhinorhino on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
FTR HOT D nn xxxx does not work
- Thread starter nuevodia
- Start date
Firebird Scrambler
Systems Engineer
You need CLS = MNL and also check if you can dial the ACOD for the route.
All the best
Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK
If it's working, then leave it alone!.
All the best
Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK
If it's working, then leave it alone!.
- Thread starter
- #4
There are thousands of SCH codes, and it is quite possible the code "number" will lead you to the problem. What was the SCH code?
--
Nortel Resources at GHTROUT.com
--
--
Nortel Resources at GHTROUT.com
--
Firebird Scrambler
Systems Engineer
Here is a working example from one of my customers below.
DES LOBBY5
TN 020 0 00 15
TYPE 500
CDEN 4D
CUST 0
WRLS NO
DN 6418 0 MARP
CPND
CPND_LANG ROMAN
NAME CORRIDOR 221
XPLN 23
DISPLAY_FMT FIRST,LAST
AST NO
IAPG 0
HUNT
TGAR 0
LDN NO
NCOS 0
SGRP 0
RNPG 0
XLST 0
SCI 0
SCPW
SFLT NO
CAC_MFC 0
CLS CTD MNL FBD XFD WTA THFD FND HTD ONS
LPR XRD AGRD CWD SWD MWD RMMD SMWD LPD XHD CCSD LND TVD
CFTD SFD MRD C6D CNID CLBD AUTU
ICDD CDMD EHTD MCTD
GPUD DPUD CFXD ARHD OVDD AGTD CLTD LDTD ASCD
MBXD UDI RCC HBTD IRGD DDGA NAMA MIND
NRWD NRCD NROD CRD PRSD MCRD
EXR0 SHL ABDD CFHD
CWND USRD BNRD OCBD RTDD RBDD RBHD FAXD PGND FTTC
AACS NO
MLWU_LANG 0
FTR HOT D 4028
DATE 12 JUL 2010
I hope this helps?
All the best
Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK
If it's working, then leave it alone!.
DES LOBBY5
TN 020 0 00 15
TYPE 500
CDEN 4D
CUST 0
WRLS NO
DN 6418 0 MARP
CPND
CPND_LANG ROMAN
NAME CORRIDOR 221
XPLN 23
DISPLAY_FMT FIRST,LAST
AST NO
IAPG 0
HUNT
TGAR 0
LDN NO
NCOS 0
SGRP 0
RNPG 0
XLST 0
SCI 0
SCPW
SFLT NO
CAC_MFC 0
CLS CTD MNL FBD XFD WTA THFD FND HTD ONS
LPR XRD AGRD CWD SWD MWD RMMD SMWD LPD XHD CCSD LND TVD
CFTD SFD MRD C6D CNID CLBD AUTU
ICDD CDMD EHTD MCTD
GPUD DPUD CFXD ARHD OVDD AGTD CLTD LDTD ASCD
MBXD UDI RCC HBTD IRGD DDGA NAMA MIND
NRWD NRCD NROD CRD PRSD MCRD
EXR0 SHL ABDD CFHD
CWND USRD BNRD OCBD RTDD RBDD RBHD FAXD PGND FTTC
AACS NO
MLWU_LANG 0
FTR HOT D 4028
DATE 12 JUL 2010
I hope this helps?
All the best
Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK
If it's working, then leave it alone!.
- Thread starter
- #7
Sorry for not replying fast enough, I been working on a bigger problem, but now i'm back to square one on this problem.
I'm tracing the line and this is what the trace gives back:
.entc 42 5 45
gotr
.12:03:36 28/04/2011
IDLE TN 042 0 00 05
.12:05:24 28/04/2011
ACTIVE TN 042 0 00 05
ORIG 042 0 00 05 MARP 0 1209 500
TERM NONE
TDTN 0 SLOT 11 PTY SLOT 11
DIAL DN 8022
MAIN_PM DIAL AUX_PM
TALKSLOT NONE
QUEU 128
CALL ID 0 1601
.12:05:44 28/04/2011
ACTIVE TN 042 0 00 05
ORIG 042 0 00 05 MARP 0 1209 500
TERM 002 18 DID RMBR 22 18
DIAL DN 8022
MAIN_PM DIAL AUX_PM COMPLETE
TALKSLOT ORIG 18 TERM 18
QUEU NONE
CALL ID 0 1601
---- ISDN PRA CALL (TERM) ----
CALL REF # = 6697
BEARER CAP = VOICE
HLC =
CALL STATE = 1 INIT
CALLING NO = 7876415400
CALLED NO =
PDCA 1 PAD 0 6 PCML MU MU
.12:05:44 28/04/2011
ACTIVE TN 042 0 00 05
ORIG 042 0 00 05 MARP 0 1209 500
TERM NONE
TDTN 0 SLOT 19 PTY SLOT 19
DIAL DN 8022
MAIN_PM REOR
TALKSLOT NONE
QUEU DIAL
CALL ID 0 1601
.12:05:44 28/04/2011
IDLE TN 042 0 00 05
.12:05:50 28/04/2011
ACTIVE TN 042 0 00 05
ORIG 042 0 00 05 MARP 0 1209 500
TERM NONE
TDTN 0 SLOT 8 PTY SLOT 8
DIAL DN 8022
MAIN_PM DIAL AUX_PM
TALKSLOT NONE
QUEU 128
CALL ID 0 1511
.12:06:10 28/04/2011
ACTIVE TN 042 0 00 05
ORIG 042 0 00 05 MARP 0 1209 500
TERM 002 18 DID RMBR 22 18
DIAL DN 8022
MAIN_PM DIAL AUX_PM COMPLETE
TALKSLOT ORIG 23 TERM 25
QUEU NONE
CALL ID 0 1511
---- ISDN PRA CALL (TERM) ----
CALL REF # = 6698
BEARER CAP = VOICE
HLC =
CALL STATE = 1 INIT
CALLING NO = 7876415400
CALLED NO =
PDCA 1 PAD 0 6 PCML MU MU
.12:06:12 28/04/2011
ACTIVE TN 042 0 00 05
ORIG 042 0 00 05 MARP 0 1209 500
TERM NONE
TDTN 0 SLOT 26 PTY SLOT 26
DIAL DN 8022
MAIN_PM REOR
TALKSLOT NONE
QUEU DIAL
CALL ID 0 1511
.12:06:12 28/04/2011
IDLE TN 042 0 00 05
The equipment (scanning machine use for inventory that call an 1800 or something like that) is suposed to be dialing an 1800 number (sorry for the redundancy), btw I tested the equipment directly to a trunk it works fine (that rules out equipment problems).
If I connect to the line a test phone it only work in pulse mode and not in dtmf mode.
I'm tracing the line and this is what the trace gives back:
.entc 42 5 45
gotr
.12:03:36 28/04/2011
IDLE TN 042 0 00 05
.12:05:24 28/04/2011
ACTIVE TN 042 0 00 05
ORIG 042 0 00 05 MARP 0 1209 500
TERM NONE
TDTN 0 SLOT 11 PTY SLOT 11
DIAL DN 8022
MAIN_PM DIAL AUX_PM
TALKSLOT NONE
QUEU 128
CALL ID 0 1601
.12:05:44 28/04/2011
ACTIVE TN 042 0 00 05
ORIG 042 0 00 05 MARP 0 1209 500
TERM 002 18 DID RMBR 22 18
DIAL DN 8022
MAIN_PM DIAL AUX_PM COMPLETE
TALKSLOT ORIG 18 TERM 18
QUEU NONE
CALL ID 0 1601
---- ISDN PRA CALL (TERM) ----
CALL REF # = 6697
BEARER CAP = VOICE
HLC =
CALL STATE = 1 INIT
CALLING NO = 7876415400
CALLED NO =
PDCA 1 PAD 0 6 PCML MU MU
.12:05:44 28/04/2011
ACTIVE TN 042 0 00 05
ORIG 042 0 00 05 MARP 0 1209 500
TERM NONE
TDTN 0 SLOT 19 PTY SLOT 19
DIAL DN 8022
MAIN_PM REOR
TALKSLOT NONE
QUEU DIAL
CALL ID 0 1601
.12:05:44 28/04/2011
IDLE TN 042 0 00 05
.12:05:50 28/04/2011
ACTIVE TN 042 0 00 05
ORIG 042 0 00 05 MARP 0 1209 500
TERM NONE
TDTN 0 SLOT 8 PTY SLOT 8
DIAL DN 8022
MAIN_PM DIAL AUX_PM
TALKSLOT NONE
QUEU 128
CALL ID 0 1511
.12:06:10 28/04/2011
ACTIVE TN 042 0 00 05
ORIG 042 0 00 05 MARP 0 1209 500
TERM 002 18 DID RMBR 22 18
DIAL DN 8022
MAIN_PM DIAL AUX_PM COMPLETE
TALKSLOT ORIG 23 TERM 25
QUEU NONE
CALL ID 0 1511
---- ISDN PRA CALL (TERM) ----
CALL REF # = 6698
BEARER CAP = VOICE
HLC =
CALL STATE = 1 INIT
CALLING NO = 7876415400
CALLED NO =
PDCA 1 PAD 0 6 PCML MU MU
.12:06:12 28/04/2011
ACTIVE TN 042 0 00 05
ORIG 042 0 00 05 MARP 0 1209 500
TERM NONE
TDTN 0 SLOT 26 PTY SLOT 26
DIAL DN 8022
MAIN_PM REOR
TALKSLOT NONE
QUEU DIAL
CALL ID 0 1511
.12:06:12 28/04/2011
IDLE TN 042 0 00 05
The equipment (scanning machine use for inventory that call an 1800 or something like that) is suposed to be dialing an 1800 number (sorry for the redundancy), btw I tested the equipment directly to a trunk it works fine (that rules out equipment problems).
If I connect to the line a test phone it only work in pulse mode and not in dtmf mode.
Looking at the origonal post:
A phone that is CLS MNL cannot also have CLS DTN or DIP.
A phone that is CLS DTN cannot have FTR HOT.
So, what we need is a printout of the phone.
If I were to guess, your equipment is the thing doing the dialing, not the phone. I bet the phone has a CLS CTD, which is the problem. It must be CLS UNR to dial the "1" after an Access Code.
--
Nortel Resources at GHTROUT.com
--
A phone that is CLS MNL cannot also have CLS DTN or DIP.
A phone that is CLS DTN cannot have FTR HOT.
So, what we need is a printout of the phone.
If I were to guess, your equipment is the thing doing the dialing, not the phone. I bet the phone has a CLS CTD, which is the problem. It must be CLS UNR to dial the "1" after an Access Code.
--
Nortel Resources at GHTROUT.com
--
- Thread starter
- #9
This is the printout of the latest trace:
10:53:30 02/05/2011
ACTIVE TN 042 0 00 05
ORIG 042 0 00 05 MARP 0 1209 500
TERM 002 20 DID RMBR 22 20
DIAL DN 8022
MAIN_PM DIAL AUX_PM COMPLETE
TALKSLOT ORIG 18 TERM 18
QUEU NONE
CALL ID 0 1634
---- ISDN PRA CALL (TERM) ----
CALL REF # = 7348
BEARER CAP = VOICE
HLC =
CALL STATE = 1 INIT
CALLING NO = 7876415400
CALLED NO =
PDCA 1 PAD 0 6 PCML MU MU
.10:53:30 02/05/2011
ACTIVE TN 042 0 00 05
ORIG 042 0 00 05 MARP 0 1209 500
TERM NONE
TDTN 0 SLOT 20 PTY SLOT 21
DIAL DN 8022
MAIN_PM REOR
TALKSLOT NONE
QUEU DIAL
CALL ID 0 1634
.10:53:36 02/05/2011
IDLE TN 042 0 00 05
10:53:30 02/05/2011
ACTIVE TN 042 0 00 05
ORIG 042 0 00 05 MARP 0 1209 500
TERM 002 20 DID RMBR 22 20
DIAL DN 8022
MAIN_PM DIAL AUX_PM COMPLETE
TALKSLOT ORIG 18 TERM 18
QUEU NONE
CALL ID 0 1634
---- ISDN PRA CALL (TERM) ----
CALL REF # = 7348
BEARER CAP = VOICE
HLC =
CALL STATE = 1 INIT
CALLING NO = 7876415400
CALLED NO =
PDCA 1 PAD 0 6 PCML MU MU
.10:53:30 02/05/2011
ACTIVE TN 042 0 00 05
ORIG 042 0 00 05 MARP 0 1209 500
TERM NONE
TDTN 0 SLOT 20 PTY SLOT 21
DIAL DN 8022
MAIN_PM REOR
TALKSLOT NONE
QUEU DIAL
CALL ID 0 1634
.10:53:36 02/05/2011
IDLE TN 042 0 00 05
- Thread starter
- #10
If I use a Test phone, after I offhook, I does not recognize the DTMF. Here is the printout of the TN:
DES HOTL
TN 042 0 00 05
TYPE 500
CDEN 4D
CUST 0
WRLS NO
DN 1209 0 MARP
AST NO
IAPG 0
HUNT
TGAR 1
LDN NO
NCOS 0
SGRP 0
RNPG 0
XLST
SCI 0
CLS UNR MNL FBD XFD WTA THFD FND HTD ONS
LPR XRD CWD SWD MWD RMMD SMWD LPD XHD SLKD CCSD TENA LND TVD
CFTD SFD MRD C6D CNID CLBD AUTU
ICDD CDMD LLCN EHTD MCTD
GPUD DPUD CFXD ARHD OVDD AGTD CLTD LDTD ASCD
MBXD CPFA CPTA DDGA NAMA MIND
MCRD
EXR0 SHL ABDD CFHD DNDY DNO3
USRD BNRD OCBD RTDD RBDD RBHD FAXD CNUD CNAD PGND FTTC
TEN 3
PLEV 02
AACS NO
MLWU_LANG 0
FTR HOT D 8022
DATE 2 MAY 2011
DES HOTL
TN 042 0 00 05
TYPE 500
CDEN 4D
CUST 0
WRLS NO
DN 1209 0 MARP
AST NO
IAPG 0
HUNT
TGAR 1
LDN NO
NCOS 0
SGRP 0
RNPG 0
XLST
SCI 0
CLS UNR MNL FBD XFD WTA THFD FND HTD ONS
LPR XRD CWD SWD MWD RMMD SMWD LPD XHD SLKD CCSD TENA LND TVD
CFTD SFD MRD C6D CNID CLBD AUTU
ICDD CDMD LLCN EHTD MCTD
GPUD DPUD CFXD ARHD OVDD AGTD CLTD LDTD ASCD
MBXD CPFA CPTA DDGA NAMA MIND
MCRD
EXR0 SHL ABDD CFHD DNDY DNO3
USRD BNRD OCBD RTDD RBDD RBHD FAXD CNUD CNAD PGND FTTC
TEN 3
PLEV 02
AACS NO
MLWU_LANG 0
FTR HOT D 8022
DATE 2 MAY 2011
Can you just HOT D to the full number? It looks like your HOT D goes to the Route Access Code.
If this Route is only used for this purpose (whatever you are configuring in this post), set the MANO=YES (it is NO by default)
--
Nortel Resources at GHTROUT.com
--
If this Route is only used for this purpose (whatever you are configuring in this post), set the MANO=YES (it is NO by default)
--
Nortel Resources at GHTROUT.com
--
- Thread starter
- #12
Why did you pick a DID route for this?
Is the ICOG=IAO?
Does anything else use this route?
Can you HOT to the full number rather than just the Access Code?
If you can answer all, it will help everyone to find a solution
--
Nortel Resources at GHTROUT.com
--
Is the ICOG=IAO?
Does anything else use this route?
Can you HOT to the full number rather than just the Access Code?
If you can answer all, it will help everyone to find a solution
--
Nortel Resources at GHTROUT.com
--
- Status
Similar threads
- Question
- Locked
- Question