I have new extensions on a kx-td1232-7. I'm going to have to permanently forward it busy/ no answer to their existing kx-tvs125 mailboxes. Is there a way to set it so that it's always on & not subject to the Fwd/Dnd key? I don't want them to hit that key accidently (turning it off)& maybe not lighting the Fwd/Dnd key would be nice......Thanks
Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
Fowarding to VM?
- Thread starter mosthigh
- Start date
rivet
Programmer
- Mar 20, 2005
- 336
yes you can put an ext intercept to 265 insted this way it wont light the led
Description Sets the Intercept Routing destination of for each jack in both day
and night modes.
Selection • Jack number: KX-TD816 – 01 through 16, (-1 / -2)
KX-TD1232 – 01 through 64, (-1 / -2)
( =all jacks, -1 = first part, -2 = second part)
• Extension number: 2 through 4 digits / Disable (no Intercept
Routing)
Default All jacks – Disable — Day / Night
Programming 1. Enter a program address (620 for day or 621 for night).
Display example: EXT Intercep Day
2. Press sp phone.
Display: Jack NO?®
3. Enter a jack number.=last 2 digits of ext
To enter jack number 01, you can also press sp phone.
To select the (annalog )second part (-2), press sp phone after entering the jack
number.
Display example: #01-1: Disable
4. Enter an extension number. (ie) voice mail ext
To change the current entry, press CLEAR and enter the new number.
To disable Intercept Routing, press CLEAR.
5. Press STORE.
6. To program another jack number, press NEXT or PREV, or
SELECT and the desired jack number.
7. Repeat steps 4 through 6.
8. Press END.
. To assign all jacks to one selection, press the key in step 3. In this
case, the display shows the contents programmed for jack 01.
•
Description Sets the Intercept Routing destination of for each jack in both day
and night modes.
Selection • Jack number: KX-TD816 – 01 through 16, (-1 / -2)
KX-TD1232 – 01 through 64, (-1 / -2)
( =all jacks, -1 = first part, -2 = second part)
• Extension number: 2 through 4 digits / Disable (no Intercept
Routing)
Default All jacks – Disable — Day / Night
Programming 1. Enter a program address (620 for day or 621 for night).
Display example: EXT Intercep Day
2. Press sp phone.
Display: Jack NO?®
3. Enter a jack number.=last 2 digits of ext
To enter jack number 01, you can also press sp phone.
To select the (annalog )second part (-2), press sp phone after entering the jack
number.
Display example: #01-1: Disable
4. Enter an extension number. (ie) voice mail ext
To change the current entry, press CLEAR and enter the new number.
To disable Intercept Routing, press CLEAR.
5. Press STORE.
6. To program another jack number, press NEXT or PREV, or
SELECT and the desired jack number.
7. Repeat steps 4 through 6.
8. Press END.
. To assign all jacks to one selection, press the key in step 3. In this
case, the display shows the contents programmed for jack 01.
•
- Thread starter
- #3
rivet
Programmer
- Mar 20, 2005
- 336
well it should not be to hard to find it so try this
press programe
type (password) ie *#6543
type 000
now use the fwd/dnd button until you find EXT Intercep Day
once you find it follow above instructions
by the looks of it panasonic have changed the numbering again
but EXT Intercep Day is what your looking for
press programe
type (password) ie *#6543
type 000
now use the fwd/dnd button until you find EXT Intercep Day
once you find it follow above instructions
by the looks of it panasonic have changed the numbering again
but EXT Intercep Day is what your looking for
- Thread starter
- #5
- Thread starter
- #7
rivet
Programmer
- Mar 20, 2005
- 336
sorry guys
your right this is something we have extra here a rather big thing to leave out of your systems below is the full manual page just to prove we can do
i wonder if a set of v6 chips from here would work in one of your systems
4.8 Extension Programming
Extension Intercept Routing — Day / Night
620-621
Description Sets the Intercept Routing destination of for each jack in both day
and night modes.
Selection • Jack number: KX-TD816 – 01 through 16, (-1 / -2)
KX-TD1232 – 01 through 64, (-1 / -2)
( =all jacks, -1 = first part, -2 = second part)
• Extension number: 2 through 4 digits / Disable (no Intercept
Routing)
Default All jacks – Disable — Day / Night
Programming 1. Enter a program address (620 for day or 621 for night).
Display example: EXT Intercep Day
2. Press NEXT.
Display: Jack NO?®
3. Enter a jack number.
To enter jack number 01, you can also press NEXT.
To select the second part (-2), press NEXT after entering the jack
number.
Display example: #01-1: Disable
4. Enter an extension number.
To change the current entry, press CLEAR and enter the new number.
To disable Intercept Routing, press CLEAR.
5. Press STORE.
6. To program another jack number, press NEXT or PREV, or
SELECT and the desired jack number.
7. Repeat steps 4 through 6.
8. Press END.
Conditions • You can set the extension numbers in programs [003] “Extension
Number Set,” [127] “Voice Mail Extension Number Assignment,” [130]
“Phantom Extension Number” and also floating numbers of hunting
groups, and pagers in program [813] “Floating Number Assignment.”
• To assign all jacks to one selection, press the key in step 3. In this
case, the display shows the contents programmed for jack 01.
• When “Disable” is selected, Intercept Routing is provided according to
the assignment in program [409]–[410].
Feature References Section 3, Features,
Intercept Routingur systems???
your right this is something we have extra here a rather big thing to leave out of your systems below is the full manual page just to prove we can do
i wonder if a set of v6 chips from here would work in one of your systems
4.8 Extension Programming
Extension Intercept Routing — Day / Night
620-621
Description Sets the Intercept Routing destination of for each jack in both day
and night modes.
Selection • Jack number: KX-TD816 – 01 through 16, (-1 / -2)
KX-TD1232 – 01 through 64, (-1 / -2)
( =all jacks, -1 = first part, -2 = second part)
• Extension number: 2 through 4 digits / Disable (no Intercept
Routing)
Default All jacks – Disable — Day / Night
Programming 1. Enter a program address (620 for day or 621 for night).
Display example: EXT Intercep Day
2. Press NEXT.
Display: Jack NO?®
3. Enter a jack number.
To enter jack number 01, you can also press NEXT.
To select the second part (-2), press NEXT after entering the jack
number.
Display example: #01-1: Disable
4. Enter an extension number.
To change the current entry, press CLEAR and enter the new number.
To disable Intercept Routing, press CLEAR.
5. Press STORE.
6. To program another jack number, press NEXT or PREV, or
SELECT and the desired jack number.
7. Repeat steps 4 through 6.
8. Press END.
Conditions • You can set the extension numbers in programs [003] “Extension
Number Set,” [127] “Voice Mail Extension Number Assignment,” [130]
“Phantom Extension Number” and also floating numbers of hunting
groups, and pagers in program [813] “Floating Number Assignment.”
• To assign all jacks to one selection, press the key in step 3. In this
case, the display shows the contents programmed for jack 01.
• When “Disable” is selected, Intercept Routing is provided according to
the assignment in program [409]–[410].
Feature References Section 3, Features,
Intercept Routingur systems???
- Thread starter
- #11
I never really found the FWD light to be a problem. I work for one of Panasonic Aust's larger dealers and we install minimum 7 systems a day and 5 of those would have voicemail at least. I've never once in the last 5 years had anyone complain about the FWD light.
- Status