Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Force a Phantom DN to use CLID Table

Status
Not open for further replies.

DWheater

MIS
Aug 23, 2013
30
GB
I'm trying to get a Phantom DN to send it's own CLID to external numbers, but it won't. The phantom DN is DCFWd to a mobile phone and when I call the Phantom's DDI number, the Mobile gets the main switchboard number, not the Phantom's CLID.

How do I force the phantom to send out it's CLID?


CLID Table
ENTRY 3
HNTN
ESA_HLCL 0113382
ESA_INHN NO
ESA_APDN NO
HLCL 0113382
DIDN YES
DIDN_LEN 4
HLOC 0113382
LSC
CLASS_FMT LCL


Phantom DN

DES HO500
TN 252 0 02 08 PHANTOM
TYPE 500
CDEN 4D
CUST 0
MRT
ERL 00000
WRLS NO
DN 7099 3 MARP
CPND
CPND_LANG ROMAN
NAME CLID Test
XPLN 27
DISPLAY_FMT FIRST,LAST
AST NO
IAPG 0
HUNT
TGAR 1
LDN NO
NCOS 7
SGRP 0
RNPG 0
LNRS 16
XLST
SCI 0
SCPW 12345
SFLT NO
CAC_MFC 0
CLS TLD DTN FBD XFD WTA THFD FND HTD ONS
LPR XRD AGRD CWD SWD MWD RMMD LPD XHD SLKD CCSD LNA TVD
CFTD SFD MRD C6D CNIA CLBD AUTU
ICDD CDMD EHTD MCTD
GPUD DPUD CFXA ARHD OVDD AGTD CLTD LDTD ASCD SDND
MBXD UDI RCC HBTD IRGD DDGA NAMA MIND
NRWD NRCD NROD SPKD CRD PRSD MCRD
EXR0 SHL SMSD ABDD CFHD DNDY DNO3
CWND USRD BNRD OCBD RTDD RBDD RBHD FAXD CNUD CNAD PGND FTTC
FDSD NOVD CDMR PRED MCDD T87D SBMD PKCH MPTD ELCD
PLEV 00
PUID
UPWD
AACS NO
MLWU_LANG 0
FTR CFW 16
FTR DCFW 16 907xxxxxxxxx
DATE 20 NOV 2013
 
On some UK telephone Exchanges, you might need to remove the initial "0" against the 0113 etc. However, I've never actually tried CLID on a Phantom DN. Also your ISDN 30 needs to be I421 or Euro ISDN 30. I'm guessing that you are on a switch in the UK, Leeds?

All the best

Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK

If it's working, then leave it alone!.
 
Look at your CLID tables, does 3 give you the option you want?
 
I don't think the CLID of the Phantom does anything, since it is never part of the call. I agree that would be great if it did - I have lots of applications for the same thing

~~
Gene at www.GHTROUT.com
 
trvlr1 - Yes, it works perfectly for the 1110 IP phones we have, they give out their DDI numbers when making calls.


GHTROUT - That's a shame, ideally I'd prefer the system to pass on the CLID from the incoming call, but I don't think that's allowed in the UK, so sending the phantom's CLID would have been a next best option, if that's not possible then I guess my users will just have to get used to it. :(


Thanks to everyone who responded :)
 
If you have Euro ISDN 30e, then I think there is a setting in the route data block to allow the incoming CLID to be passed through the CS1000 system. I can't remember where I found it, it might have been a previous thread on Tek-Tips?.

All the best

Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK

If it's working, then leave it alone!.
 
I don't suppose the same setting would be present on SIP trunks would it? I'll have a look see if I can find it, thanks.
 
Check out the flexible CLID manipulation feature. You can modify the outgoing CLID in a similar fashion to how you modify incoming numbers with IDC. You build a table and apply the table to entries on an RLI.


 
I've had a look at some of the RDB prompts and have spotted MBXR and SIND. I'm not sure if one of them related to passing on the CLID in and out of the phone system?. Does your SIP RDB have these prompts?.

All the best

Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK

If it's working, then leave it alone!.
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top