FC100/S on E4500

[micosat]

I have a E4500 with I/O Card and an Additional SBUS FC100/S connected. The IO Card also has FC25/S builtin.

Both the FC100/S and FC25/S are connected to A5000 array. But only the FC25/S connection is working.

#luxadm fcal

Found Path to 0 FC100/S Cards
Complete
#

However /usr/platform/sun4u/sbin/prtdiag -v shows the card is inserted:

System Configuration: Sun Microsystems sun4u 8-slot Sun Enterprise E4500/E5500
System clock frequency: 100 MHz
Memory size: 2048Mb

========================= CPUs =========================

Run Ecache CPU CPU
Brd CPU Module MHz MB Impl. Mask
--- --- ------- ----- ------ ------ ----
0 0 0 400 8.0 US-II 10.0
0 1 1 400 8.0 US-II 10.0
2 4 0 400 8.0 US-II 10.0
2 5 1 400 8.0 US-II 10.0


========================= Memory =========================

Intrlv. Intrlv.
Brd Bank MB Status Condition Speed Factor With
--- ----- ---- ------- ---------- ----- ------- -------
0 1 1024 Active OK 60ns 2-way A
2 1 1024 Active OK 60ns 2-way A

========================= IO Cards =========================

Bus Freq
Brd Type MHz Slot Name Model
--- ---- ---- ---------- -------------------------------- ----------------------
1 SBus 25 0 SUNW,soc 501-2069
1 SBus 25 1 SUNW,soc 501-2069
1 SBus 25 3 SUNW,hme
1 SBus 25 3 SUNW,fas/sd (block)
1 SBus 25 13 SUNW,socal/sf (scsi-3) 501-3060

Detached Boards
===============
Slot State Type Info
---- --------- ------ -----------------------------------------
3 disabled disk Disk 0: Target: 0 Disk 1: Target: 1

No failures found in System
===========================

No System Faults found
======================


========================= Environmental Status =========================
Keyswitch position is in Normal Mode
System Power Status: Minimum Available
System LED Status: GREEN YELLOW GREEN
Normal ON OFF BLINKING


Fans:
-----
Unit Status
---- ------
Rack OK
Key OK
AC OK

System Temperatures (Celsius):
------------------------------
Brd State Current Min Max Trend
--- ------- ------- --- --- -----
0 OK 34 33 34 stable
1 OK 43 43 44 stable
2 OK 37 37 37 stable
CLK OK 32 32 32 stable


Power Supplies:
---------------
Supply Status
--------- ------
0 OK
1 OK
PPS OK
System 3.3v OK
System 5.0v OK
Peripheral 5.0v OK
Peripheral 12v OK
Auxilary 5.0v OK
Peripheral 5.0v precharge OK
Peripheral 12v precharge OK
System 3.3v precharge OK
System 5.0v precharge OK
AC Power OK


========================= HW Revisions =========================

ASIC Revisions:
---------------
Brd FHC AC SBus0 SBus1 PCI0 PCI1 FEPS Board Type Attributes
--- --- -- ----- ----- ---- ---- ---- ---------- ----------
0 1 5 CPU 100MHz Capable
1 1 5 1 1 22 Dual-SBus-SOC+ 100MHz Capable
2 1 5 CPU 100MHz Capable
3 Unknown 100MHz Capable

System Board PROM revisions:
----------------------------
Board 0: OBP 3.2.30 2002/10/25 14:03 POST 3.9.30 2002/10/25 14:04
Board 1: FCODE 1.8.30 2002/10/25 14:02 iPOST 3.4.30 2002/10/25 14:03
Board 2: OBP 3.2.30 2002/10/25 14:03 POST 3.9.30 2002/10/25 14:04

The 501-3060 checks out on sunsolve as FC100/S

However when I do probe-fcal-all I only get the FC25/S showing up...

Luxadm shows that the 2nd link is not up


# luxadm display R2D2

SENA
DISK STATUS
SLOT FRONT DISKS (Node WWN) REAR DISKS (Node WWN)
0 On (O.K.) 20000020371893aa On (O.K.) 2000002037cf009c
1 On (O.K.) 20000020375bd456 On (O.K.) 2000002037187b04
2 On (O.K.) 20000020375aa316 On (Bypassed:AB)
3 On (O.K.) 20000020371875f6 On (O.K.) 2000002037736e41
4 On (O.K.) 2000002037a513de On (O.K.) 20000020374656c5
5 On (O.K.) 2000002037c8624a On (O.K.) 200000203789b725
6 On (O.K.) 20000020371877ce On (O.K.) 200000203789c2b7
SUBSYSTEM STATUS
FW Revision:1.09 Box ID:1 Node WWN:508002000006f828 Enclosure Name:R2D2
Power Supplies (0,2 in front, 1 in rear)
0 O.K.(rev.-02) 1 O.K.(rev.-02) 2 O.K.(rev.-02)
Fans (0 in front, 1 in rear)
0 O.K.(rev.-04) 1 O.K.(rev.-00)
ESI Interface board(IB) (A top, B bottom)
A: O.K.(rev.-04)
GBIC module (1 on left, 0 on right in IB)
0 O.K.(mod.-05)
1 Not Installed
B: O.K.(rev.-04)
GBIC module (1 on left, 0 on right in IB)
0 Failed(mod.-05): Not receiving a signal
1 Not Installed
Disk backplane (0 in front, 1 in rear)
Front Backplane: O.K.(rev.-04)
Temperature sensors (on front backplane)
0:37ºC 1:37ºC 2:36ºC 3:34ºC 4:36ºC 5:36ºC
6:37ºC (All temperatures are NORMAL.)
Rear Backplane: O.K.(rev.-04)
Temperature sensors (on rear backplane)
0:37ºC 1:37ºC 2:34ºC 3:36ºC 4:36ºC 5:36ºC
6:37ºC (All temperatures are NORMAL.)
Interconnect assembly
O.K.(rev.-02)
Loop configuration
Loop A is configured as a single loop.
Loop B is configured as a single loop.
Language USA English
#

I have tried to update the FCAL PROM but LUXADM fails too se the card!

 

[unixjr]

Hi i have the same problem. did you get a work around for this ? Please keep me posted..

 

[IonDrive]

Hi Micosat,

You got this exactly reversed

"I have a E4500 with I/O Card and an Additional SBUS FC100/S connected. The IO Card also has FC25/S builtin."

Actually the prtconf output shows that the FC100 functionality is built-into the IO board - the FC/25S is the SBus card you've got plugged in. You can prove this by taking out the IO board and checking the part number on the SBus card and see for yourself.

The clue is here:

"========================= IO Cards =========================

Bus Freq
Brd Type MHz Slot Name Model
--- ---- ---- ---------- -------------------------------- ----------------------
1 SBus 25 0 SUNW,soc 501-2069
1 SBus 25 1 SUNW,soc 501-2069
1 SBus 25 3 SUNW,hme
1 SBus 25 3 SUNW,fas/sd (block)
1 SBus 25 13 SUNW,socal/sf (scsi-3) 501-3060"

Slot 13 = built-in So the built-in fibre connector pair is 100MB/s and so it is correct that the A5x00 works when connected to here. The A5x00 is 100MB/s only. The older SSA is 25MB/s only and one of them would work on either of the 2 SOC HBA SBus cards which you have installed in that IO board.

Does that make sense now?