Thanks for the replies.
I have tried numerous things to change the port on the callpilot and all have failed. I did use the laptop and got these logs, there are 2-3 boot sequences per text file. I am at the point i have to tell the customer he has to replace something but to be honest i'm not sure what. Can someone take a look at the logs, see if they notice something out of the ordinary and suggest a plan of action. TIA Mike
Trial1
CallPilot 150 Boot Loader V1.5.19
(C) 2001 Nortel Networks
--------------------------------------------------------------------------
NETWORK INTERFACE PARAMETERS:
IP address on LAN is 192.168.0.145
LAN interface's subnet mask is 0xffffff00
HARDWARE PARAMETERS:
Serial channels will use a baud rate of 9600
This board's ethernet address is 0:19:E1:F0:67:EF
CALLPILOT BOOTLOADER PARAMETERS:
Execution Mode: Load CallPilot
Source File System Parameters:
Device: ATA Disk
Source File List Name: fil
Destination File System Parameters:
Device: ATA Disk
File List Name: filelst.lst
Format Target Device: Y
Boot File Name: CallPilot.bin
After board is reset, start-up code will wait 2 seconds
--------------------------------------------------------------------------
To change any of this, press any key within 2 seconds
Automatic Update Mode Enabled!
To Change Update Mode to Manual, press any key within 10 seconds
Updating in Automatic Mode!
Initializing ATA Disk... Done.
Initializing PCMCIA Stack ...SSInit: CS_Sockets - 2,Num_PWindows - 8
Card services Init complete found 2 sockets.
Done.
Initializing PCMCIA ATA Disk Drives ...SILICONSYSTEMS VER2.00
AtaInit: completed
Done.
Detecting ATA Cards...
Device found in Slot A:
Model: SILICONSYSTEMS INC 64MB
Serial: 496VTP63Sq601SP01919
Rev.: 2.29l
Mounted 10.256
Loading 10.256/CallPilot.bin... Done.
Unmounting 10.256
Transferring control to the downloaded code
I-Cache ON, D-Cache ON
Downloaded OS and application executing f
Memory Test Completed Successfully
Starting root(RAM)
Initializing D-channel driver
Initialized for 4 channels
Disk volume 3.0.0, initialized...
Initializing ATA Disk... Done.
Initializing PCMCIA Stack ...Card services Init complete found 2 sockets.
Done.
Initializing PCMCIA ATA Disk Drives ...SILICONSYSTEMS VER2.00
AtaInit: completed
Done.
Detecting ATA Cards... Card(s) detected
Verifying 7.0
PPP: Using hardcoded ip address 192.168.0.2
PPP: Username is CallPilot
PPP: Password is administrator
PPP: Adding PPP NI
Standard output device initialized...
7.1\safe not found
Pseudo device initialized...
TFTP device initialized...
Type "test" to stop auto boot
Login: Starting Access/2 and Voicemail
SysConfig file does not exist. Use default!!!
Opening DSP Msg logfile
DSP[0]: 1.50.51.A8 Oct 04, 2004
DSP Abstraction Layer Binding to port 5001
DSP Abstraction Layer Accepting...
Language Debug: Reading '7.1\access2\runtime\alarm0.dat'.
Read language file '7.1\access2\runtime\alarm0.dat'.
Loaded 1 of 1 language file(s). De
Curr File Pool Path='7.0\access2\FILEPOOL\0\*.*'
Curr File Pool Path='7.1\access2\FILEPOOL\0\*.*'
TCM 1: Channel 0: UP
dcd: CH0 is opened.
TCM 2: Channel 2: UP
dcd: CH2 is opened.
DCHCNTRL - DCH0 Reader created
DCHCNTRL - DCH1 Reader created
DCHCNTRL - DCH2 Reader created
DCHCNTRL - DCH3 Reader created
DCHCNTRL - Number of D-channels trying :2
dchMon: Initialized FumpSTM of Dchannel No : 2
dchMon: Initialized FumpSTM of Dchannel No : 1
DCHCNTRL - Active channel = 2 D Channel State = 255
dch: channel 2 Msg Len 99 U
dch: channel 2 Msg Len 99 Update Board to Access
D-channel No. 1 is working
D-channel No. 2 is working
Got KSU Version from functerm: ----30CRE06H}
***>>>TelInit telNumITInfoElemBytes 5
******************
Loaded 1 of 1 language file(s). Default language: 0 (hex).
* *
* ! R E A D Y ! *
* _ *
******************
Access up in 37 seconds
Starting voicemail
Country: NORTH AMERICA
Alternate QZ Mapping: 0
AMIS Address Start Key: #
Application SName: VM
Default Language {enum from country
Enable TT Gate: 0
Group List Lead Digit: 9
Key Language Toggle: 9
Key Operator Revert: 0
Login Mailbox Key: *
Local Number Length: 7
Maximum CLID display: 7
Maximum CLID entry: 16
Maximum Network DN Length: 16
Maximum Packet Network DN Length: 16
National Number Length: 10
SC Maximum Lines 10 20: 334
Voicemail CORE Ready...
CallPilot 150 Boot Loader V1.5.19
(C) 2001 Nortel Networks
--------------------------------------------------------------------------
NETWORK INTERFACE PARAMETERS:
IP address on LAN is 192.168.0.145
LAN interface's subnet mask is 0xffffff00
HARDWARE PARAMETERS:
Serial channels will use a baud rate of 9600
This board's ethernet address is 0:19:E1:F0:67:EF
CALLPILOT BOOTLOADER PARAMETERS:
Execution Mode: Load CallPilot
Source File System Parameters:
Device: ATA Disk
Source File List Name: filelst.lst
Destination File System Parameters:
Device: ATA Disk
File List Name: filelst.lst
Format Target Device: Y
Boot File Name: CallPilot.bin
After board is reset, start-up code will wait 2 seconds
--------------------------------------------------------------------------
To change any of this, press any key within 2 seconds
Automatic Update Mode Enabled!
To Change Update Mode to Manual, press any key within 10 seconds
Updating in Automatic Mode!
Initializing ATA Disk... Done.
Initializing PCMCIA Stack ...SSInit: CS_Sockets - 2,Num_PWindows - 8
Card services Init complete found 2 sockets.
Done.
Initializing PCMCIA ATA Disk Drives ...SILICONSYSTEMS
AtaInit: completed
Done.
Detecting ATA Cards...
Device found in Slot A:
Model: SILICONSYSTEMS INC 64MB
Serial: 496VTP63Sq601SP01919
Rev.: 2.29l
Mounted 10.256
Loading 10.256/CallPilot.bin... Done.
Unmounting 10.256
Transferring control to the downloaded code
I-Cache ON, D-Cache ON
Downloaded OS and application executing from RAM
Memory Test Completed Successfully
Starting root(RAM)
Initializing D-channel driver
Initialized for 4 channels
Disk volume 3.0.0, initialized...
Initializing ATA Disk... Done.
Initializing PCMCIA Stack ...Card services Init complete found 2 sockets.
Done.
Initializing PCMCIA ATA Disk Drives ...SILICONSYSTEMS VER2.00
AtaInit: completed
Done.
Detecting ATA Cards... Card(s) detected
Verifying 7.0
PPP: Using hardcoded ip address 192.168.0.2
PPP: Username is CallPilot
PPP: Password is administrator
PPP: Adding PPP NI...
Standard output device initialized...
7.1\safe not found
Pseudo device initialized...
TFTP device initialized...
Type "test" to stop auto boot
Login: Starting Access/2 and
SysConfig file does not exist. Use default!!!
Opening DSP Msg logfile
DSP[0]: 1.50.51.A8 Oct 04, 2004
DSP Abstraction Layer Binding to port 5001
DSP Abstraction Layer Accepting...
Language Debug: Reading '7.1\access2\runtime\alarm0.dat'.
Read language file '7.1\access2\runtime\alarm0.dat'.
Loaded 1 of 1 language file(s). Default language: 0 (hex).
Curr File Pool Path='7.0\access2\FILEPOOL\0\*.*'
Curr File Pool Path='7.1\access2\FILEPOOL\0\*.*'
TCM 1: Channel 0: UP
dcd: CH0 is opened.
TCM 2: Channel 2: UP
dcd: CH2 is opened.
DCHCNTRL - DCH0 Reader created
DCHCNTRL - DCH1 Reader created
DCHCNTRL - DCH2 Reader created
DCHCNTRL - DCH3 Reader created
DCHCNTRL - Number of D-channels trying :2
dchMon: Initialized FumpSTM of Dchannel No : 2
dchMon: Initialized FumpSTM of Dchannel No : 1
DCHCNTRL - Active channel = 2 D Channel State = 255
dch: channel 2 Msg Len 99 Update Board to Access
dch: channel 2 Msg Len 99 Update Board to Access
D-channel No. 2 is working
D-channel No. 1 is working
Got KSU Version from functerm: ---
***>>>TelInit telNumITInfoElemBytes 5
******************
Loaded 1 of 1 language file(s). Default language: 0 (hex).
* *
* ! R E A D Y ! *
* _ *
******************
Access up in 36 seconds
Starting voicemail
Country: NORTH AMERICA
Alternate QZ Mapping: 0
AMIS Address Start Key: #
Application SName: VM
Default Language {enum from country.c}: 0
Enable TT Gate: 0
Group List Lead Digit: 9
Key Language Toggle: 9
Key Operator Revert: 0
Login Mailbox Key: *
Local Number Length: 7
Maximum CLID display: 7
Maximum CLID entry: 16
Maximum Network DN Length: 16
Maximum Packet Network DN Length: 16
National Number Length: 10
SC Maximum Lines 10 20: 334
Voicemail CORE Ready...
CallPilot 150 Boot Loader V1.5.19
(C) 2001 Nortel Networks
--------------------------------------------------------------------------
NETWORK INTERFACE PARAMETERS:
IP address on LAN is 192.168.0.145
LAN interface's subnet mask is 0xffffff00
HARDWARE PARAMETERS:
Serial channels will use a baud rate of 9600
This board's ethernet address is 0:19:E1:F0:67:EF
CALLPILOT BOOTLOADER PARAMETERS:
Execution Mode: Load CallPilot
Source File System Parameters:
Device: ATA Disk
Source File List Name: filelst.lst
Destination File System Parameters:
Device: ATA Disk
File List Name: filelst.lst
Format Target Device: Y
Boot File Name: CallPilot.bin
After board is reset, start-up code will wait 2 seconds
--------------------------------------------------------------------------
To change any of this, press any key within 2 seconds
Automatic Update Mode Enabled!
To Change Update Mode to Manual, press any key within 10 seconds
Updating in Automatic Mode!
Initializing ATA Disk... Done.
Initializing PCMCIA Stack ...SSInit: CS_Sockets - 2,Num_PWindows - 8
Card services Init complete found 2 sockets.
Done.
Initializing PCMCIA ATA Disk Drives ...SILICONSYSTEMS VER2.00
AtaInit: completed
Done.
Detecting ATA Cards...
Device found in Slot A:
Model: SILICONSYSTEMS INC 64MB
Serial: 496VT
Rev.: 2.29l
Mounted 10.256
Loading 10.256/CallPilot.bin... Done.
Unmounting 10.256
Transferring control to the downloaded code
I-Cache ON, D-Cache ON
Downloaded OS and application executing from RAM
Memory Test Completed Successfully
Starting root(RAM)
Initializing D-channel driver
Initialized for 4 channels
Disk volume 3.0.0, initialized...
Initializing ATA Disk... Done.
Initializing PCMCIA Stack ...Card services Init complete found 2 sockets.
Done.
Initializing PCMCIA ATA Disk Drives ...SILICONSYSTEMS VER2
AtaInit: completed
Done.
Detecting ATA Cards... Card(s) detected
Verifying 7.0
PPP: Using hardcoded ip address 192.168.0.2
PPP: Username is CallPilot
PPP: Password is administrator
PPP: Adding PPP NI...
Standard output device initialized...
7.1\safe not found
Pseudo device initialized...
TFTP device initialized...
Type "test" to stop auto boot
Login: Starting Access/2 and Voicemail
SysConfig file does not exist. Use default!!!
Opening DSP Msg logfile
DSP[0]: 1.50.51.A8 Oct 04, 2004
DSP Abstraction Layer Binding
DSP Abstraction Layer Accepting...
Language Debug: Reading '7.1\access2\runtime\alarm0.dat'.
Read language file '7.1\access2\runtime\alarm0.dat'.
Loaded 1 of 1 language file(s). Default language: 0 (hex).
Curr File Pool Path='7.0\access2\FILEPOOL\0\*.*'
Curr File Pool Path='7.1\access2\FILEPOOL\0\*.*'
TCM 1: Channel 0: DOWN
TCM 2: Channel 2: UP
dcd: CH2 is opened.
DCHCNTRL - DCH0 Reader created
DCHCNTRL - DCH1 Reader created
DCHCNTRL - DCH2 Reader created
DCHCNTRL - DCH3 Reader created
DCHCNTRL - Number of D-channels trying :2
dchMon: Initialized FumpSTM of Dchannel No : 2
DCHCNTRL - Active channel = 2 D Channel State = 255
dch: channel 2 Msg Len 99 Update Board to Access
D-channel No. 2 is working
CallPilot 150 Boot Loader V1.5.19
(C) 2001 Nortel Networks
--------------------------------------------------------------------------
NETWORK INTERFACE PARAMETERS:
IP address on LAN is 192.168.0.145
LAN interface's subnet mask is 0xffffff00
HARDWARE PARAMETERS:
Serial channels will use a baud
This board's ethernet address is 0:19:E1:F0:67:EF
CALLPILOT BOOTLOADER PARAMETERS:
Execution Mode: Load CallPilot
Source File System Parameters:
Device: ATA Disk
Source File List Name: filelst.lst
Destination File System Parameters:
Device: ATA Disk
File List Name: filelst.lst
Format Target Device: Y
Boot File Name: CallPilot.bin
After board is reset, start-up code will wait 2 seconds
--------------------------------------------------------------------------
To change any of this, press any key within 2 seconds
Automatic Update Mode Enabled!
To Change Update Mode to Manual, press any key within 10 seconds
Updating in Automatic Mode!
Initializing ATA Disk... Done.
Initializing PCMCIA Stack ...SSInit: CS_Sockets - 2,Num_PWindows - 8
Card services Init complete found 2 sockets.
Done.
Initializing PCMCIA ATA Disk Drives ...SILICONSYSTEMS VER2.00
AtaInit: completed
Done.
Detecting ATA Cards...
Device found in Slot A:
Model: SILICONSYSTEMS INC 64MB
Serial: 496VT
Rev.: 2.29l
Mounted 10.256
Loading 10.256/CallPilot.bin... Done.
Unmounting 10.256
Transferring control to the downloaded code
I-Cache ON, D-Cache ON
Downloaded OS and application executing from RAM
Memory Test Completed Successfully
Starting root(RAM)
Initializing D-channel driver
Initialized for 4 channels
Disk volume 3.0.0, initialized...
Initializing ATA Disk... Done.
Initializing PCMCIA Stack ...Card services Init complete found 2 sockets.
Done.
Initializing PCMCIA ATA Disk Drives ...SILICONSYSTEMS VER2
AtaInit: completed
Done.
Detecting ATA Cards... Card(s) detected
Verifying 7.0
PPP: Using hardcoded ip address 192.168.0.2
PPP: Username is CallPilot
PPP: Password is administrator
PPP: Adding PPP NI...
Standard output device initialized...
7.1\safe not found
Pseudo device initialized...
TFTP device initialized...
Type "test" to stop auto boot
Login: Starting Access/2 and Voicemail
SysConfig file does not exist. Use default!!!
Opening DSP Msg logfile
DSP[0]: 1.50.51.A8 Oct 04, 2004
DSP Abstraction Layer Binding
DSP Abstraction Layer Accepting...
Language Debug: Reading '7.1\access2\runtime\alarm0.dat'.
Read language file '7.1\access2\runtime\alarm0.dat'.
Loaded 1 of 1 language file(s). Default language: 0 (hex).
Curr File Pool Path='7.0\access2\FILEPOOL\0\*.*'
Curr File Pool Path='7.1\access2\FILEPOOL\0\*.*'
TCM 1: Channel 0: UP
dcd: CH0 is opened.
TCM 2: Channel 2: UP
dcd: CH2 is opened.
DCHCNTRL - DCH0 Reader created
DCHCNTRL - DCH1 Reader created
DCHCNTRL - DCH2 Reader created
DCHCNTRL - DCH3 Reader created
DCHCNTRL - Number of D-channels trying :2
dchMon: Initialized FumpSTM of Dchannel No : 1
dchMon: Initialized FumpSTM of Dchannel No : 2
DCHCNTRL - Active channel = 2 D Channel State = 255
dch: channel 2 Msg Len 99 Update Board to Access
dch: channel 2 Msg Len 99 Update Board to Access
D-channel No. 1 is working
D-channel No. 2 is working
dcd 0:receive unknown msg c0
Got KSU Version from functerm: ----30CRE06H}
***>>>TelInit telNumITInfoElemBytes 5
******************
Loaded 1 of 1 language file(s). Default lan
Loaded 1 of 1 language file(s). Default lan
* ! R E A D Y ! *
* _ *
******************
Access up in 40 seconds
Starting voicemail
Country: NORTH AMERICA
Alternate QZ Mapping: 0
AMIS Address Start Key: #
Application SName: VM
Default Language {enum from country.c}: 0
Enable TT Gate: 0
Group List Lead Digit: 9
Key Language Toggle: 9
Key Operator Revert: 0
Login Mailbox Key: *
Local Number Length: 7
Maximum CLID display: 7
Maximum CLID entry: 16
Maximum Network DN Length: 16
Maximum Packet Network DN Length: 16
National Number Length: 10
SC Maximum Lines 10 20: 334
Voicemail CORE Ready...
Trial2
dch: channel 2 Msg Len 99 Update Board to Access
D-channel No. 2 is working
D-channel No. 1 is working
Got KSU Version from functerm: ---
***>>>TelInit telNumITInfoElemBytes 5
******************
Loaded 1 of 1 language file(s). Default language: 0 (hex).
* *
* ! R E A D Y ! *
* _ *
******************
Access up in 36 seconds
Starting voicemail
Country: NORTH AMERICA
Alternate QZ Mapping: 0
AMIS Address Start Key: #
Application SName: VM
Default Language {enum from country.c}: 0
Enable TT Gate: 0
Group List Lead Digit: 9
Key Language Toggle: 9
Key Operator Revert: 0
Login Mailbox Key: *
Local Number Length: 7
Maximum CLID display: 7
Maximum CLID entry: 16
Maximum Network DN Length: 16
Maximum Packet Network DN Length: 16
National Number Length: 10
SC Maximum Lines 10 20: 334
Voicemail CORE Ready...
CallPilot 150 Boot Loader V1.5.19
(C) 2001 Nortel Networks
--------------------------------------------------------------------------
NETWORK INTERFACE PARAMETERS:
IP address on LAN is 192.168.0.145
LAN interface's subnet mask is 0xffffff00
HARDWARE PARAMETERS:
Serial channels will use a baud rate of 9600
This board's ethernet address is 0:19:E1:F0:67:EF
CALLPILOT BOOTLOADER PARAMETERS:
Execution Mode: Load CallPilot
Source File System Parameters:
Device: ATA Disk
Source File List Name: filelst.lst
Destination File System Parameters:
Device: ATA Disk
File List Name: filelst.lst
Format Target Device: Y
Boot File Name: CallPilot.bin
After board is reset, start-up code will wait 2 seconds
--------------------------------------------------------------------------
To change any of this, press any key within 2 seconds
Automatic Update Mode Enabled!
To Change Update Mode to Manual, press any key within 10 seconds
Updating in Automatic Mode!
Initializing ATA Disk... Done.
Initializing PCMCIA Stack ...SSInit: CS_Sockets - 2,Num_PWindows - 8
Card services Init complete found 2 sockets.
Done.
Initializing PCMCIA ATA Disk Drives ...SILICONSYSTEMS VER2.00
AtaInit: completed
Done.
Detecting ATA Cards...
Device found in Slot A:
Model: SILICONSYSTEMS INC 64MB
Serial: 496VT
Rev.: 2.29l
Mounted 10.256
Loading 10.256/CallPilot.bin... Done.
Unmounting 10.256
Transferring control to the downloaded code
I-Cache ON, D-Cache ON
Downloaded OS and application executing from RAM
Memory Test Completed Successfully
Starting root(RAM)
Initializing D-channel driver
Initialized for 4 channels
Disk volume 3.0.0, initialized...
Initializing ATA Disk... Done.
Initializing PCMCIA Stack ...Card services Init complete found 2 sockets.
Done.
Initializing PCMCIA ATA Disk Drives ...SILICONSYSTEMS VER2
AtaInit: completed
Done.
Detecting ATA Cards... Card(s) detected
Verifying 7.0
PPP: Using hardcoded ip address 192.168.0.2
PPP: Username is CallPilot
PPP: Password is administrator
PPP: Adding PPP NI...
Standard output device initialized...
7.1\safe not found
Pseudo device initialized...
TFTP device initialized...
Type "test" to stop auto boot
Login: Starting Access/2 and Voicemail
SysConfig file does not exist. Use default!!!
Opening DSP Msg logfile
DSP[0]: 1.50.51.A8 Oct 04, 2004
DSP Abstraction Layer Binding
DSP Abstraction Layer Accepting...
Language Debug: Reading '7.1\access2\runtime\alarm0.dat'.
Read language file '7.1\access2\runtime\alarm0.dat'.
Loaded 1 of 1 language file(s). Default language: 0 (hex).
Curr File Pool Path='7.0\access2\FILEPOOL\0\*.*'
Curr File Pool Path='7.1\access2\FILEPOOL\0\*.*'
TCM 1: Channel 0: DOWN
TCM 2: Channel 2: UP
dcd: CH2 is opened.
DCHCNTRL - DCH0 Reader created
DCHCNTRL - DCH1 Reader created
DCHCNTRL - DCH2 Reader created
DCHCNTRL - DCH3 Reader created
DCHCNTRL - Number of D-channels trying :2
dchMon: Initialized FumpSTM of Dchannel No : 2
DCHCNTRL - Active channel = 2 D Channel State = 255
dch: channel 2 Msg Len 99 Update Board to Access
D-channel No. 2 is working
CallPilot 150 Boot Loader V1.5.19
(C) 2001 Nortel Networks
--------------------------------------------------------------------------
NETWORK INTERFACE PARAMETERS:
IP address on LAN is 192.168.0.145
LAN interface's subnet mask is 0xffffff00
HARDWARE PARAMETERS:
Serial channels will use a baud
This board's ethernet address is 0:19:E1:F0:67:EF
CALLPILOT BOOTLOADER PARAMETERS:
Execution Mode: Load CallPilot
Source File System Parameters:
Device: ATA Disk
Source File List Name: filelst.lst
Destination File System Parameters:
Device: ATA Disk
File List Name: filelst.lst
Format Target Device: Y
Boot File Name: CallPilot.bin
After board is reset, start-up code will wait 2 seconds
--------------------------------------------------------------------------
To change any of this, press any key within 2 seconds
Automatic Update Mode Enabled!
To Change Update Mode to Manual, press any key within 10 seconds
Updating in Automatic Mode!
Initializing ATA Disk... Done.
Initializing PCMCIA Stack ...SSInit: CS_Sockets - 2,Num_PWindows - 8
Card services Init complete found 2 sockets.
Done.
Initializing PCMCIA ATA Disk Drives ...SILICONSYSTEMS VER2.00
AtaInit: completed
Done.
Detecting ATA Cards...
Device found in Slot A:
Model: SILICONSYSTEMS INC 64MB
Serial: 496VT
Rev.: 2.29l
Mounted 10.256
Loading 10.256/CallPilot.bin... Done.
Unmounting 10.256
Transferring control to the downloaded code
I-Cache ON, D-Cache ON
Downloaded OS and application executing from RAM
Memory Test Completed Successfully
Starting root(RAM)
Initializing D-channel driver
Initialized for 4 channels
Disk volume 3.0.0, initialized...
Initializing ATA Disk... Done.
Initializing PCMCIA Stack ...Card services Init complete found 2 sockets.
Done.
Initializing PCMCIA ATA Disk Drives ...SILICONSYSTEMS VER2
AtaInit: completed
Done.
Detecting ATA Cards... Card(s) detected
Verifying 7.0
PPP: Using hardcoded ip address 192.168.0.2
PPP: Username is CallPilot
PPP: Password is administrator
PPP: Adding PPP NI...
Standard output device initialized...
7.1\safe not found
Pseudo device initialized...
TFTP device initialized...
Type "test" to stop auto boot
Login: Starting Access/2 and Voicemail
SysConfig file does not exist. Use default!!!
Opening DSP Msg logfile
DSP[0]: 1.50.51.A8 Oct 04, 2004
DSP Abstraction Layer Binding
DSP Abstraction Layer Accepting...
Language Debug: Reading '7.1\access2\runtime\alarm0.dat'.
Read language file '7.1\access2\runtime\alarm0.dat'.
Loaded 1 of 1 language file(s). Default language: 0 (hex).
Curr File Pool Path='7.0\access2\FILEPOOL\0\*.*'
Curr File Pool Path='7.1\access2\FILEPOOL\0\*.*'
TCM 1: Channel 0: UP
dcd: CH0 is opened.
TCM 2: Channel 2: UP
dcd: CH2 is opened.
DCHCNTRL - DCH0 Reader created
DCHCNTRL - DCH1 Reader created
DCHCNTRL - DCH2 Reader created
DCHCNTRL - DCH3 Reader created
DCHCNTRL - Number of D-channels trying :2
dchMon: Initialized FumpSTM of Dchannel No : 1
dchMon: Initialized FumpSTM of Dchannel No : 2
DCHCNTRL - Active channel = 2 D Channel State = 255
dch: channel 2 Msg Len 99 Update Board to Access
dch: channel 2 Msg Len 99 Update Board to Access
D-channel No. 1 is working
D-channel No. 2 is working
dcd 0:receive unknown msg c0
Got KSU Version from functerm: ----30CRE06H}
***>>>TelInit telNumITInfoElemBytes 5
******************
Loaded 1 of 1 language file(s). Default lan
* *
* ! R E A D Y ! *
* _ *
******************
Access up in 40 seconds
Starting voicemail
Country: NORTH AMERICA
Alternate QZ Mapping: 0
AMIS Address Start Key: #
Application SName: VM
Default Language {enum from country.c}: 0
Enable TT Gate: 0
Group List Lead Digit: 9
Key Language Toggle: 9
Key Operator Revert: 0
Login Mailbox Key: *
Local Number Length: 7
Maximum CLID display: 7
Maximum CLID entry: 16
Maximum Network DN Length: 16
Maximum Packet Network DN Length: 16
National Number Length: 10
SC Maximum Lines 10 20: 334
Voicemail CORE Ready...
DCHCNTRL - ALERT: All TCMs are Out of Sync. Reset hardware if a new KSU is conne
cted.
DCHCNTRL - ALERT: System will restart after 120 seconds
DCHCNTRL - ALERT: To stop rebooting, enter stopreboot
System will reboot in 1 seconds
Synchronizing volume 7.0 ... Done!
I-Cache ON, D-Cache ON
Downloaded OS and application executing from RAM
Memory Test Completed Successfully
Starting root(RAM)
Initializing D-channel driver
Initialized for 4
Disk volume 3.0.0, initialized...
Initializing ATA Disk... Done.
Initializing PCMCIA Stack ...Card services Init complete found 2 sockets.
Done.
Initializing PCMCIA ATA Disk Drives ...SILICONSYSTEMS VER2.00
AtaInit: completed
Done.
Detecting ATA Cards... Card(s) detected
Verifying 7.0
PPP: Using hardcoded ip address 192.168.0.2
PPP: Username is CallPilot
PPP: Password is administrator
PPP: Adding PPP NI...
Standard output device initialized...
7.1\safe not found
Pseudo device initialized...
TFTP device initializ
Type "test" to stop auto boot
Login: Starting Access/2 and Voicemail
SysConfig file does not exist. Use default!!!
Opening DSP Msg logfile
DSP[0]: 1.50.51.A8 Oct 04, 2004
DSP Abstraction Layer Binding to port 5001
DSP Abstraction Layer Accepting...
Language Debug: Reading '7.1\access2\runtime\alarm0.dat'.
Read language file '7.1\access2\runtime\alarm0.dat'.
Loaded 1 of 1 language file(s). Default language: 0 (hex).
Curr File Pool Path='7.0\access2\FILEPOOL\0\*.*'
Curr File Pool Path='7.1\access2\FILEPO
TCM 1: Channel 0: DOWN
TCM 2: Channel 2: DOWN
DCHCNTRL - DCH0 Reader created
DCHCNTRL - DCH1 Reader created
DCHCNTRL - DCH2 Reader created
DCHCNTRL - DCH3 Reader created
DCHCNTRL - Number of D-channels trying :2
DCHCNTRL - ALERT: All TCMs are Out of Sync. Reset hardware if a new KSU is conne
cted.
DCHCNTRL - ALERT: System will restart after 120 seconds
DCHCNTRL - ALERT: To stop rebooting, enter stopreboot
System will reboot in 1 seconds
Synchronizing volume 7.0 ... Done!
I-Cache ON, D-Cache ON
Downloaded OS and application executing from RAM
(C) 2001 Nortel Networks
Memory Test Completed Successfully----------------------------------
Starting root(RAM)----------
Initializing D-channel driver
Initialized for 4 channelsARAMETERS:
Disk volume 3.0.0, initialized...s 192.168.0.145
Initializing ATA Disk... Done.ce's subnet mask is 0xffffff00
Initializing PCMCIA Stack ...Card services Init complete found 2 sockets.
Serial channels will use a baud rate of 9600
Done.
Initializing PCMCIA ATA Disk Drives ...SILICONSYSTEMS VER2.000:67:EF
CA
AtaInit: completedPARAMETERS:
Done.
Detecting ATA Cards... Card(s) detectedPilot
Verifying 7.0ystem Paramet
PPP: Using hardcoded ip address 192.168.0.2vice: ATA Disk
So
PPP: Username is CallPilot
Pseudo device initialized...Boot File Name: CallPilot.bi
TFTP device initialized...
After board is
Type "test" to stop auto boot seconds
Login: Starting Access/2 and Voicemail--------------------------------------
SysConfig file does not exist. Use default!!!
Opening DSP Msg logfilee any of this, press an
DSP[0]: 1.50.51.A8 Oct 04, 2004
DSP Abstraction Layer Binding to port 5001d!
To Change
DSP Abstraction Layer Accepting...ey within 10 seconds
Language Debug: Reading '7.1\access2\runtime\alarm0.dat'.n Automatic Mode!
Initializing A
Read language file '7.1\access2\runtim
Done.
DCHCNTRL - DCH0 Reader created
Device fo
DCHCNTRL - DCH1 Reader created
Model: SILICONSYST
DCHCNTRL - DCH2 Reader created
Serial: 49
DCHCNTRL - DCH3 Reader created
Rev.:
DCHCNTRL - Number of D-channels trying :2
Loading 10.256/CallPilot.bin... D
DCHCNTRL - ALERT: All TCMs are Out of Sync. Reset hardware if a new KSU is connesferring control to the downloaded code
cted.Cache
DCHCNTRL - ALERT: System will restart after 120 secondsapplication executing f
Disk volume 3.0.0,
I-Cache ON, D-Cache ON
Downloaded OS and application executing from RAM
Initializing PCMCIA Stack ...Car
Memory Test Completed Successfullyckets.
Starting root(RAM)
Initializing D-channel driverzing PCMCIA ATA Disk Drives .
Initialized for 4 channels
Disk volume 3.0.0, initialized...aInit: completed
Initializing ATA Disk... Done.ds... Card(s) detected
Initializing PCMCIA Stack ...Card services Init complete found 2 sockets.coded ip address 192.168.0.2
P
Done.rname
Initializing PCMCIA ATA Disk Drives ...SILICONSYSTEMS VER2.00strator
PPP: Adding PPP NI
Type "test" to st
PPP: Username is CallPilot
Login: St
PPP: Password is administrator
PPP: Adding PPP NI...does not exist. Use d
Standard output device initialized...
Opening DSP Msg logfi
7.1\safe not found
DSP[0]: 1.5
Pseudo device initialized...
DSP A
TFTP device initialized... port 5001
Type "test" to stop auto bootbstraction Layer Accepting...
Login: Starting Access/2 and Voicemailguage Debug: Reading '7.1\access2\runt
SysConfig file does not exist. Use default!!!
Read langua
Opening DSP Msg logfiletime\alarm0.dat'.
DSP[0]: 1.50.51.A8 Oct 04, 2004
Loaded 1 o
DSP Abstraction Layer Binding
DCHCNTRL - DCH0 Reader created
DCHCNTRL - DCH1 Reader createdTM of Dchannel No : 1
DCHCNTRL - DCH2 Reader created
DCHCNTRL - Active chann
DCHCNTRL - DCH3 Reader created
DCHCNTRL - Number of D-channels tryig Len 99 U
DCHCNTRL - ALERT: To stop rebooting, enter stopreboot
******************
System will reboot in 1 seconds1 language file(s). Default lan
Synchronizing volume 7.0 ... Done!
I-Cache ON, D-Cache ON *
Downloaded OS and application executing from RAM *
******************
Memory Test Completed Successfullyds
Starting
Starting root(RAM)
Country:
Initializing D-channel driver
Alternate QZ Mapping
Initialized for 4 channels
AMIS Address Start Key:
Disk volume 3.0.0, initialized...ation SName: VM
Initializing ATA Disk... Done.m country
Verifying 7.0
Maximum P
PPP: Using hardcoded ip address 192.168.0.2
National Number Lengt
PPP: Username is CallPilot
SC Maximum Lines 10
PPP: Password is administrator
Voicemail CORE Ready...
PPP: Adding PPP NI...
CallPilot 150 Bo
Standard output device initialized...
(C) 2001 Nortel Networks
7.1\safe not found
------------
Pseudo device initialized...----------------------------
TFTP device initialized...
Type "test" to stop auto bootRK INTERFACE PARAMETERS:
Login: Starting Access/2 and
DCHCNTRL - DCH1 Reader created------------------------------
DCHCNTRL - DCH2 Reader created
DCHCNTRL - DCH3 Reader created
To change any of t
DCHCNTRL - Number of D-channels trying :2
dchMon: Initialized FumpSTM of Dchannel No : 1
To Change Update Mode to
dchMon: Initialized FumpSTM of Dchannel No : 2
DCHCNTRL - Active channel = 2 D Channel State = 255
Initializing ATA Disk... Done.
dch: channel 2 Msg Len 99 Update Board to Accessk ...SSInit: CS_Sockets - 2,Num_PWindows - 8
dch: channel 2 Msg Len 99 Update Board to Access
Card services Init complete found
D-channel No. 1 is working
D-channel No. 2 is workingg PCMCIA ATA Disk Drives .
Got KSU Version from functerm: ---
* ! R E A D Y ! *
* _ *
******************
Access up in 43 seconds
Starting voicemail
Country: NORTH AMERICA
Alternate QZ Mapping: 0
AMIS Address Start Key: #
Application SName: VM
Default Language {enum from country.c}: 0
Enable TT Gate: 0
Group List Lead Digit: 9
Key Language Toggle: 9
Key Operator Revert: 0
Login Mailbox Key: *
Local Number Length: 7
Maximum CLID display: 7
Maximum CLID entry: 16
Maximum Network DN Length: 16
Maximum Packet Network DN Length: 16
National Number Length: 10
SC Maximum Lines 10 20: 334
Voicemail CORE Ready...
Thanks