Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations TouchToneTommy on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

ELNK not coming up

Status
Not open for further replies.

nortelhawk

IS-IT--Management
Aug 9, 2004
47
GB
Hi,

i have one 61C ....i have been trying to put that up on LAN using Transceivers but failed to do so ....Related configurations done by me as follows -

>ld 117

OAM000

=> prt elnk

ACTIVE ETHERNET: "HSBCVIZAGPRI" "136.52.93.12"
INACTIVE ETHERNET: "HSBCVIZAGSECON" "136.52.93.13"
OK

=> prt host

ID Hostname IP Address
1 LOCAL_PPP_IF 137.135.192.4
2 REMOTE_PPP_IF 100.1.1.1
3 GATEWAY 136.52.93.254
4 HSBCVIZAGPRI 136.52.93.12
5 HSBCVIZAGSECON 136.52.93.13
OK
=> prt route

ID Network Gateway
1 0.0.0.0 136.52.93.254
OK

=> prt mask

SUBNET MASK: "255.255.254.0"
OK

>ld 22

PT2000

REQ prt

TYPE adan tty

ADAN TTY 12
CTYP PTY
DNUM 12
PORT 1
DES ELAN
FLOW NO
USER MTC SCH BUG
XSM NO
TTYLOG 0
BANR YES

>ld 117

OAM000
=> prt route

ID Network Gateway
1 0.0.0.0 136.52.93.254
OK

=> enl route 1

ROUTE: "0.0.0.0" "136.52.93.254" enabled
OK

=> stat route

*** Active Internet Routing Table ***
ID Network Gateway
1 0.0.0.0 136.52.93.254
-- 136.52.92.0 136.52.93.12
-- 127.0.0.1 127.0.0.1

=> => prt host

ID Hostname IP Address
1 LOCAL_PPP_IF 137.135.192.4
2 REMOTE_PPP_IF 100.1.1.1
3 GATEWAY 136.52.93.254
4 HSBCVIZAGPRI 136.52.93.12
5 HSBCVIZAGSECON 136.52.93.13
OK

=> stat host

*** Active Internet Host Table ***
ID Hostname IP Address
-- localhost 127.0.0.1
-- PRIMARY_ENET 137.135.128.253
-- SECONDARY_ENET 137.135.128.254
1 LOCAL_PPP_IF 137.135.192.4
2 REMOTE_PPP_IF 100.1.1.1
4 HSBCVIZAGPRI 136.52.93.12

=> ****

>ld 137

CIOD000
.stat elnk


ELNK DISABLED (Disabled by User)
.
N 055 00 2460 A020 018 11/16 13:19:46 00:00:16 .0 A81009152468
& 000 000
& 000


CIOD000
.enl elnk


OK
.


CIOD000
.


CIOD000
.stat elnk


ELNK ENABLED
Ethernet (ln unit number 0):
Host: HSBCVIZAGPRI
Internet address: 136.52.93.12
Broadcast address: 136.52.93.255
Ethernet address: 00:60:38:15:06:cc
Netmask: 0xffff0000; Subnetmask: 0xfffffe00
0 packets received; 0 packets sent
58346 input errors; 0 output errors
0 collisions

Now the network is Ok and all physical connections are done(transceivers & cables from M1 to hub) but still i am not able to ping 136.52.93.12 . Also i am not able to login to switch using Rlogin.....also with time the number of input errors in the LD137 stat elnk keeps on increasing rapidly.

Also the transceivers are brand new ones so chances of them being faulty is very very less. Also on transceivers the Tx light glows steady green but Rx light continously blinks green.

Please help me regarding what can be the reason or wot went wrong as the link is not coming up .......
 
hi

i think you ned to do this:

ld 117

chg elnk active HSBCVIZAGPRI

and also update dbs

hope it helps
 
all configurations looks fine. (and it should work).

how about checking the physical connections? patch cords, etc.? are you using a hub or a switch? did you check the vlan settings on the switch?
 
Hi,

checked all the physical connectivity(they are OK) &

ld 117

chg elnk active HSBCVIZAGPRI

update dbs

but still no use .......situation is same ..........

Somebody also told me that use ENL ROUTE x in ld117.
i did that but it gives the following error-

LNK278 Enable ROUTE: "0.0.0.0" "136.52.93.254" failed.
OK

i m not able to understand wot is goin wrong ....the gateway(136.52.93.254) is pinging from normal PC on the lan.....

Any clues ??????
 
look close at your subnet mask, your not on the same network on both ends if i can read.. set the subnet in the switch to a larger network .. 255.255.255.0 as oppossed to 255.255.255.252... that sub net can only have to address usable..ie x.x.x.253 and 254... 252 being the network number and 255 being the loopback

john poole
bellsouth business
columbia,sc
 
Hi john,

But my subnet mask is 255.255.254.0......shud i change that to 255.255.255.0 .

thanx
 
If I'm reading this right, you have a host defined with the same IP address as your route destination. (yeah, I know that it is not the active host) Try removing that host (OUT HOST 3) and doing an UPDATE DBS
 
Hi sandyml,

well host 3 is actually gateway which i guess we need to add and also that should be the route destination too .hence its done ......if i out the host 3 then in my host table there wont be any gateway .....may be i m wrong so waitin for ur advise regarding shall i do wot u suggested .........

thanx
 
no your using a /23 network, and that is very large, i thought you were using a /30... reset your default route to 0.0.0.0 0.0.0.0 and see ifyou can ping between the .12 and the 254...it looks like that is the interface i would make active and out the ones not in use. i thought the gatway should be my active it not the next hop

john poole
bellsouth business
columbia,sc
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top