DTI TIE Line between Nortel and Mitel

[Engine1]

I am attempting to configure a TIE line between a CS1000 and SX2000.

I know nothing about the Mitel system and I don't think th distributor does either.....

I have been through various configurations and can get it working in on direction only. Depending on the configuration used it is either Nortel to Mitel works or the opposite.

I could certainly use some advise on the best configuration of the Nortel and what to to the Mitel guy to do to his system.

 

[johnpoole]

might get a hint in the mitel forum.. are you using qsig?

john poole
bellsouth business
columbia,sc

 

[Engine1]

DTI TIE Line between Nortel and Mitel

No QSIG here...

 

[phonz1]

So what happens when to try to loop the circuit to each others equipt? do you have contiuity?

 

[Engine1]

The circuit is up and running. Depending on the siganlling config, calls will work in one direction. Sometimes it is NT to Mitel, others it is Mitel to NT.

 

[phonz1]

can you post the route, a tn from the route and is the Mitel net or user if a dchannel is used?

 

[Engine1]

NO DCH HERE THIS IS DTI

TYPE RDB
CUST 00
ROUT 2
DES MITEL
TKTP TIE
M911P NO
ESN NO
CNVT NO
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP DTI
ISDN NO
DSEL VCE
PTYP DTT
AUTO NO
DNIS NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 4702
TARG 01
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
ANTK
SIGO STD
STYP SDAT
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3

IENB 5
TFD 0
VSS 0
VGD 6
SST 5 0
NEDC ORG
FEDC ORG
CPDC NO
DLTN NO
HOLD 02 02 40
SEIZ 02 02
SVFL 02 02
DRNG NO
CDR NO
VRAT NO


PAGE 002

MUS NO
RACD NO
MANO NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TDET NO
TTBL 0
ATAN NO
OHTD NO
PLEV 2
ALRM NO
ART 0
SGRP 0
ARDN NO
AACR NO

REQ: ****
OVL000
>ld 20

PT0000
REQ: prt
TYPE: tnb
TN 30 1
DATE
PAGE
DES

DES
TN 030 01 VIRTUAL
TYPE TIE
CDEN SD
CUST 0
TRK DTI
PDCA 1
PCML MU
NCOS 0
RTMB 2 1
TGAR 1
SIGL LDR
STRI/STRO IMM IMM
SUPN YES
AST NO
IAPG 0
CLS UNR DTN CND ECD WTA LPR APN THFD HKD SPCD
P10 NTC MID
TKID
AACR NO
DATE 13 NOV 2007

 

[jftg73]

i used the next config for cs1000m 61c and icp 3300 mitel
with r2 dti and work it in boths sides


Rout
----

TYPE RDB
CUST 00
ROUT 26
DES HELPDESK
TKTP TIE
NPID_TBL_NUM 0
ESN NO
RPA NO
CNVT NO
SAT NO
IDEF NET
RCLS INT
DTRK YES
DGTP DTI2
ISDN NO
DSEL VOD
PTYP DTT
AUTO NO
DNIS NO
ICOG IAO
SRCH RRB
TRMB YES
STEP
ACOD 9992
TARG 01
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
ANTK
SIGO STD
STYP SDAT
MFC R2MF
INDMF NO
MFCI 2
R2MD NO
SGL YES
BSSU YES
MFCO 2
OPP NORM
SWP NORM
ICIS YES
ICNP UKWN
ICNT UKWN
ICPS YES
OGIS YES
PTUT 0
TIMR MFC 65408
MFO 0
MFID 0
ICF 512
OGF 512
EOD 29952
DSI 34944
NRD 10112
DDL 70
ODT 4096
RGV 640
GTO 896
GTI 896
SFB 3
IENB 5
TFD 0
VSS 0
VGD 6
SST 5 0
DTD YES
XTDT 00
MDTD 31
DTDF 00 00
SCDT NO
2 DT NO
NEDC ETH
FEDC ETH
CPDC NO
DLTN YES
HOLD 02 02 40
SEIZ 02 02
SVFL 02 02
DRNG NO
CDR YES
INC YES
LAST YES
QREC NO
OAL YES
AIA YES
OAN YES
OPD YES
NDP EXC 0
CDRX NO
NATL YES
SSL
CFWR NO
IDOP NO
VRAT NO
MUS YES
MRT 46
PANS YES
MANO NO
FRL 0 0
FRL 1 1
FRL 2 2
FRL 3 3
FRL 4 4
FRL 5 5
FRL 6 6
FRL 7 7
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TDET NO
TTBL 1
PNNC NO
ATAN NO
OHTD NO
PLEV 2
OPR NO
ALRM NO
NCNI 0
CNIE NO
CNIT NO
CTAT YES
ART 0
OPDL 0
PECL NO
DCTI 0
TIDY 9992 26
NADT 0
SGRP 0
FRIN NO
RRBS NO
RLSM 0
CCBA NO
AACR NO






channels
---------
DES HELP3
TN 018 01
TYPE TIE
CUST 0
TRK DTI2
SICA 1
PDCA 1
PCML A
NCOS 0
RTMB 26 1
TGAR 0
AST NO
IAPG 0
CLS UNR MFC CND WTA LPR APN THFD XREP BARD
P10 MID
MFL 0
MFPD NO
TKID
DATE 2 SEP 2003

 

[Engine1]

Thanks for the DTI2 Config. I told the Mitel folks that I was done with them and made them configure a PRI. I am using IFC = NI2 with the M1 as net. I have used this config several times withno trouble. Odd that I could not make a DTI span work.