DS1 installation problem

[efrosinia]

Any assistance would be much appreciated...

We ordered 2 new PRI to act as additional members on our existing trunk group that already has 82 members. We are using an exiting signaling group.

We have installed 2 TN464GP DS1 cards (without an external 120A1 CSU).

AT&T is not able to see our equiment.

DS1s are configured as such:
Location: 02A09 Name: new
Bit Rate: 1.544 Line Coding: b8zs
Line Compensation: 1 Framing Mode: esf
Signaling Mode: isdn-ext

Interface Companding: mulaw
Idle Code: 11111111

Slip Detection? n Near-end CSU Type: integrated

Echo Cancellation? n
ESF DATA LINK OPTIONS

Network Management Protocol: tabs
Send ANSI-T1.403 One-Second Performance Reports? n
Far-end CSU Address: b

INTEGRATED CSU OPTIONS
Transmit LBO: 0db
Receive ALBO: 26db
Upon DTE LOS: loopback

CPE LOOPBACK JACK OPTIONS
Supply CPE Loopback Jack Power? n

We have 4 other DS1 configured the exact same way (different TN) and they work just fine.

What am I missing? Do I need to purchase an external CSU?

Thank you

 

[AvayaTier3]

display your existing signal-group.
You need to add the boards and interface numbers on the signal-group form, then add the B-channels as ports on the trunk-group.

Note: interface numbers must match the interface numbers of the provider

A great teacher, does not provide answers, but methods to teach others "How and where to find the answers"

bsh

36 years Bell, AT&T, Lucent, Avaya
Tier 3 for 26 years and counting

http://bshtele.com

 

[efrosinia]

Here is my Signal Group Confige:

Group Number: 2 Group Type: isdn-pri
Associated Signaling? n Max number of NCA TSC: 1 Primary D-Channel: 01A1524 Max number of CA TSC: 15 Secondary D-Channel: 01B1824 Trunk Group for NCA TSC:
Trunk Group for Channel Selection:
TSC Supplementary Service Protocol: a Network Call Transfer? n
Trunk Brd Interface ID Trunk Brd Interface ID
1: 01A15 0 11:
2: 01B18 1 12:
3: 01A16 2 13:
4: 01C04 3 14:
5: 02A09 4 15:
6: 02A11 5 16:
7: 17:

All Members of the circuit were also added to my Trunk Group and were present during the cut.

Do I need to ask AT&T for the Interface IDs?

 

[efrosinia]

Test Board" for this DS1.

Port Mtce Name Alt. Name Test No. Result Error Code
02A09 UDS1-BD 138 FAIL
02A09 UDS1-BD 139 PASS
02A09 UDS1-BD 140 PASS
02A09 UDS1-BD 141 PASS
02A09 UDS1-BD 142 PASS
02A09 UDS1-BD 143 PASS
02A09 UDS1-BD 144 PASS
02A09 UDS1-BD 145 PASS
02A09 UDS1-BD 146 PASS
02A09 UDS1-BD 1227 ABORT 1951

 

[leftyx]

Signaling Mode: isdn-ext:

For all of my PRI's they are set to:"Signaling Mode: isdn-pri"

 

[efrosinia]

ISDN-PRI is used if you have a D-Channel on your circuits.
Do you have any other suggestions for me?

 

[Midstream]

Failing test 138 means it's not plugged in, or there's something wrong with your physical connection. You asked about an external CSU. You show an "integrated" CSU on the DS-1 form.

Your alarm:
1951 ABORT The ICSU Status LEDs Test cot be executed because a 120A CSU module
or a 401A T1 sync splitter is not physically installed. If using a 120A CSU
module/T1 sync splitter, physically connect it to the TN767 or TN464 board
on the back of the port carrier. Otherwise, ignore this abort

Do you have a 120 CSU plugged into the back of the TN464?

 

[efrosinia]

I do not have a CSU and don't know if I need one. Several of my DS1 do not have one and work just fine.

DS1 installed, Signal group provision and Trunk Group updated with the new members. All cabling has been replaced.

MPOE is in the Basement, we are on the 11th floor and are using straight through CAT5.