Hi to all,
We want to consolidate our DID trunks and our outgoing T1 into one PRI. We just installed the PRI, so we can move our DIDs over - right now the DIDs are coming in via DID trunk lines.
I have two questions. The first one is:
How do I tell the PRI to route the call to the proper extension? Our did range starts with 3100 to 3199. Right now, we are deleting the first two digits and replacing them with 35.
DID TRUNK INFORMATION
A Trk SS/PP Blk DiscTime Type ExpDig DelDig AddDig Signal InvDest
A 841 7/ 1 1 500ms Wink 4 2 35 TouchTone BkupExt
A 842 7/ 2 1 500ms Wink 4 2 35 TouchTone BkupExt
A 843 7/ 3 1 500ms Wink 4 2 35 TouchTone BkupExt
A 844 7/ 4 1 500ms Wink 4 2 35 TouchTone BkupExt
A 845 7/ 5 1 500ms Wink 4 2 35 TouchTone BkupExt
A 846 7/ 6 1 500ms Wink 4 2 35 TouchTone BkupExt
A 847 7/ 7 1 500ms Wink 4 2 35 TouchTone BkupExt
A 848 7/ 8 1 500ms Wink 4 2 35 TouchTone BkupExt
And the other questions is why do I see the chanels for the T1 in slot 4 when I do a print out for the PRI? Is this normal? When we turned up the new PRI, the provider didn't have any issues as far as seeing my D-channel and B channels.
PRI INFORMATION
Slot 9 Switch: 5ESS
System: By line
BchnlGrp #: Slot: TestTelNum: NtwkServ: Incoming Routing:
1 4 CallbyCall By Line Appearance
Channel ID: 23 22 21 20 19 18 17 16 15 14
13 12 11 10 9 8 7 6 5 4
3 2 1
Line PhoneNumber NumberToSend
BchnlGrp #: Slot: TestTelNum: NtwkServ: Incoming Routing:
2 9 CallbyCall By Dial Plan
Channel ID: 23 22 21 20 19 18 17 16 15 14
13 12 11 10 9 8 7 6 5 4
3 2 1
Line PhoneNumber NumberToSend
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
Network Selection Table
Entry Number: 0 1 2 3
Pattern to Match: 101**** 10***
Special Service Table
Entry Number: 0 1 2 3 4 5 6 7
Pattern to Match: 011 010 01 00 0 1
PRI INFORMATION
Operator: none OP OP OP/P OP none none none
Type of Number: I I I N N N N N
Digits to Delete: 3 3 2 2 1 1 0 0
Call-By-Call Service Table
Entry Number: 0 1 2 3 4
Pattern 0: 0
Pattern 1: 1
Pattern 2: 2
Pattern 3: 3
Pattern 4: 4
Pattern 5: 5
Pattern 6: 6
Pattern 7: 7
Pattern 8: 8
Pattern 9: 9
Call Type: BOTH BOTH BOTH BOTH BOTH
NtwkServ: No Service
DeleteDigits: 0 0 0 0 0
Entry Number: 5 6 7 8 9
Call Type: BOTH BOTH BOTH BOTH BOTH
NtwkServ:
DeleteDigits: 0 0 0 0 0
Dial Plan Routing Table
Entry Number: 0 1 2 3
NtwkServ: Any service
Expected Digits: 0 0 0 0
Pattern to Match:
Digits to Delete: 0 0 0 0
Digits to Add:
Entry Number: 4 5 6 7
NtwkServ:
Expected Digits: 0 0 0 0
Pattern to Match:
Digits to Delete: 0 0 0 0
Digits to Add:
Entry Number: 8 9 10 11
NtwkServ:
Expected Digits: 0 0 0 0
Pattern to Match:
Digits to Delete: 0 0 0 0
Digits to Add:
Entry Number: 12 13 14 15
NtwkServ:
Expected Digits: 0 0 0 0
Pattern to Match:
Digits to Delete: 0 0 0 0
Digits to Add:
One more question:
How do I configure the extensions to use one particular pool? or how do I assign my new PRI to one pool, and for all the extension to use that pool when dialing 9 to make an outside call?
Thanks.
We want to consolidate our DID trunks and our outgoing T1 into one PRI. We just installed the PRI, so we can move our DIDs over - right now the DIDs are coming in via DID trunk lines.
I have two questions. The first one is:
How do I tell the PRI to route the call to the proper extension? Our did range starts with 3100 to 3199. Right now, we are deleting the first two digits and replacing them with 35.
DID TRUNK INFORMATION
A Trk SS/PP Blk DiscTime Type ExpDig DelDig AddDig Signal InvDest
A 841 7/ 1 1 500ms Wink 4 2 35 TouchTone BkupExt
A 842 7/ 2 1 500ms Wink 4 2 35 TouchTone BkupExt
A 843 7/ 3 1 500ms Wink 4 2 35 TouchTone BkupExt
A 844 7/ 4 1 500ms Wink 4 2 35 TouchTone BkupExt
A 845 7/ 5 1 500ms Wink 4 2 35 TouchTone BkupExt
A 846 7/ 6 1 500ms Wink 4 2 35 TouchTone BkupExt
A 847 7/ 7 1 500ms Wink 4 2 35 TouchTone BkupExt
A 848 7/ 8 1 500ms Wink 4 2 35 TouchTone BkupExt
And the other questions is why do I see the chanels for the T1 in slot 4 when I do a print out for the PRI? Is this normal? When we turned up the new PRI, the provider didn't have any issues as far as seeing my D-channel and B channels.
PRI INFORMATION
Slot 9 Switch: 5ESS
System: By line
BchnlGrp #: Slot: TestTelNum: NtwkServ: Incoming Routing:
1 4 CallbyCall By Line Appearance
Channel ID: 23 22 21 20 19 18 17 16 15 14
13 12 11 10 9 8 7 6 5 4
3 2 1
Line PhoneNumber NumberToSend
BchnlGrp #: Slot: TestTelNum: NtwkServ: Incoming Routing:
2 9 CallbyCall By Dial Plan
Channel ID: 23 22 21 20 19 18 17 16 15 14
13 12 11 10 9 8 7 6 5 4
3 2 1
Line PhoneNumber NumberToSend
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
Network Selection Table
Entry Number: 0 1 2 3
Pattern to Match: 101**** 10***
Special Service Table
Entry Number: 0 1 2 3 4 5 6 7
Pattern to Match: 011 010 01 00 0 1
PRI INFORMATION
Operator: none OP OP OP/P OP none none none
Type of Number: I I I N N N N N
Digits to Delete: 3 3 2 2 1 1 0 0
Call-By-Call Service Table
Entry Number: 0 1 2 3 4
Pattern 0: 0
Pattern 1: 1
Pattern 2: 2
Pattern 3: 3
Pattern 4: 4
Pattern 5: 5
Pattern 6: 6
Pattern 7: 7
Pattern 8: 8
Pattern 9: 9
Call Type: BOTH BOTH BOTH BOTH BOTH
NtwkServ: No Service
DeleteDigits: 0 0 0 0 0
Entry Number: 5 6 7 8 9
Call Type: BOTH BOTH BOTH BOTH BOTH
NtwkServ:
DeleteDigits: 0 0 0 0 0
Dial Plan Routing Table
Entry Number: 0 1 2 3
NtwkServ: Any service
Expected Digits: 0 0 0 0
Pattern to Match:
Digits to Delete: 0 0 0 0
Digits to Add:
Entry Number: 4 5 6 7
NtwkServ:
Expected Digits: 0 0 0 0
Pattern to Match:
Digits to Delete: 0 0 0 0
Digits to Add:
Entry Number: 8 9 10 11
NtwkServ:
Expected Digits: 0 0 0 0
Pattern to Match:
Digits to Delete: 0 0 0 0
Digits to Add:
Entry Number: 12 13 14 15
NtwkServ:
Expected Digits: 0 0 0 0
Pattern to Match:
Digits to Delete: 0 0 0 0
Digits to Add:
One more question:
How do I configure the extensions to use one particular pool? or how do I assign my new PRI to one pool, and for all the extension to use that pool when dialing 9 to make an outside call?
Thanks.