DID ISSUE

[nasa123]

I configured a new E1 line for DID but incomings calls are not terminated neither can i access the trunks to dial out (system is CS1KE).

I turned on DCH trace and i get the following message when i try calling in

DCH 11 UIPE_IMSG CC_SETUP_IND REF 0000360D CH 11 7 TOD 18:23:04 CK 01726961
CALLING #:776383917 NUM PLAN: E164 TON: NATL
CALLED #:6430 NUM PLAN: E164 TON: UNKNOWN

DCH 11 UIPE_OMSG CC_REJECT_REQ REF 0000B60D CH 11 7 TOD 18:23:04 CK 01726962
CAUSE: #42 - SWED EQIP CONGESTION


When i try calling out, i do not see any message on the DCH trace.

PSTN number is 33829XXXX. below is my configuration


>ld 21
PT1000

REQ: prt
TYPE: rdb
CUST 0
ROUT 9

TYPE RDB
CUST 00
ROUT 9
DES SONATEL
TKTP DID
NPID_TBL_NUM 0
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP PRI2
ISDN YES
MODE PRA
IFC EURO
CNTY ETSI
SBN NO
PNI 00000
NCNA NO
NCRD NO
ISAR NO
CPFXS YES
SDID NO
DAPC NO
INTC NO
MBXR NO
DSEL VOD
PTYP DCO
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
RANX NO
SRCH RRB
TRMB YES
STEP
ACOD 4300
TCPP NO
TARG 01
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
MFC NO
ICIS YES
OGIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GTO 896
GTI 896
SFB 3
NBS 2048


PAGE 002

NBL 4096

IENB 5
VSS 0
VGD 6
DTD NO
SCDT NO
2 DT NO
DDO NO
DRNG YES
NDRI 00
CDR NO
NATL YES
SSL
CFWR NO
IDOP NO
VRAT NO
MUS NO
MR NO
PANS YES
RACD NO
EQAR NO
FRL 0 0
FRL 1 1
FRL 2 2
FRL 3 3
FRL 4 4
FRL 5 5
FRL 6 6
FRL 7 7
OHQ NO
OHQT 00
TTBL 0
ATAN NO
PLEV 2
OPR NO
PRDL NO
EOS NO
DNSZ 0
RCAL NO
MCTS NO
ALRM NO
BTT 30
ACKW NO
ART 0
PECL NO
DCTI 0
TIDY 4300 9
SGRP 0
ARDN NO
AACR NO

REQ: end
>ld 20

PT0000
REQ: prt
TYPE: tnb
TN 0
CDEN **

REQ: prt
TYPE: tnb
TN 11 1
DATE
PAGE
DES

DES SONATEL_1
TN 011 01 VIRTUAL
TYPE DID
CDEN SD
CUST 0
TRK PRI2
PDCA 1
PCML A
NCOS 0
RTMB 9 1
B-CHANNEL SIGNALING
NITE
AST NO
IAPG 0
CLS UNR DIP CND ECD WTA LPR APN THFD SPCD
P10 VNL
TKID
DTCR NO
AACR NO
DATE 14 MAR 2007


NACT
REQ: end
>ld 73
DDB000
MEM AVAIL: (U/P): 98832892 USED U P: 5348005 88924 TOT: 104269821
DISK SPACE NEEDED: 129 KBYTES
REQ prt
TYPE pri2
FEAT syti


MGCLK 0 1 3
PREF 0 1 3
SREF
CCGD 15
CCAR 15
EFCS YES

MEM AVAIL: (U/P): 98832892 USED U P: 5348005 88924 TOT: 104269821
DISK SPACE NEEDED: 129 KBYTES
REQ prt
TYPE pri2
FEAT lpti
LOOP 11

MFF AFF
ACRC NO
ALRM REG
RAIE NO
G1OS YES
SLP 255 1 H 30 1 H
BPV 128 122
CRC 201 97
FAP 128 122
RATS 10
GP2 255 100 S 12 S 12 S 4 S
MNG1 15 S
NCG1 15 S
OSG1 15 S
MNG2 15 S
NCG2 15 S
OSG2 15 S
PERS 254
CLRS 100
OOSC 0
MEM AVAIL: (U/P): 98832892 USED U P: 5348005 88924 TOT: 104269821
DISK SPACE NEEDED: 129 KBYTES
REQ end

>ld 21
PT1000

REQ: prt
TYPE: ldn
TYPE LDN_DATA
CUST 0

TYPE LDN_DATA
CUST 00
OPT NLDN
DLDN NO
LDN0 33829
LDN1
LDN2
LDN3
LDN4
LDN5
ICI 00 LD0
ICI 01 LD1
ICI 02 LD2
ICI 03
ICI 04 RLL
ICI 05 DL0
ICI 06 LCT
ICI 07 CFN
ICI 08 CFB
ICI 09 INT
ICI 10
ICI 11
ICI 12
ICI 13
ICI 14
ICI 15
ICI 16
ICI 17
ICI 18
ICI 19

REQ:

 

[bigindian65]

what is the controller tag? stat the clocks first.

ssck 12 0
ENBL
CLOCK ACTIVE
CLOCK CONTROLLER - LOCKED TO SLOT 1
PREF - 1
SREF - 2
AUTO SWREF CLK - ENBL

Mato' Was'aka

 

[Wane47]

is this a new system install or a existing system that you added a e1 to.

 

[nasa123]

This is what i get

ssck 0 1
ENBL
CLOCK ACTIVE
CLOCK CONTROLLER - DTI063
PREF - 3
SREF -
AUTO SWREF CLK - ENBL

 

[bigindian65]

primary ref w/ no secondary. what do you get on ld 73 prt out of ddb?

Mato' Was'aka

 

[KiwiOz07]

Suggest you look at the interzone bandwidth for the MGC the PRI is in and the IP phones. I have seen that message
"CAUSE: #42 - SWED EQIP CONGESTION" where the inter zone bandwidth is so low a call cannot be established.
I would also check that the codecs on the Node = codecs in the MGC configuration.

 

[nasa123]

i have just log the case with Nortel. i will post back what the fix is.

i thank all you forumite that have taken the pain to respond.

 

[bignose21]

Just for your interest if you need to out the CC.

LD 60
. dis cc 0 1

Then LD 73
REQ chg
TYPE pri2
FEAT syti
MGCLK x0 1
MGCLK

 

[nasa123]

thanx so much bignose21, i will sure note that