DID for E&M Trunks

[srtelengine]

I have acquired a 61C running 25.40 that has 2 tie trunks configured as E&M4 that terminate to a Strata Dialer. My problem is that it is not passing CLID for incoming calls here is the configuration of my trunk and route:
TN 012 01
TYPE TIE
CUST 0
TRK DTI
PDCA 1
PCML MU
NCOS 5
RTMB 74 1
TGAR 1
SIGL EM4
STRI/STRO WNK WNK
SUPN YES
AST NO
IAPG 0
CLS CTD DTN CND ECD WTA LPR APN THFD HKD
P10 VNL
TYPE RDB
CUST 00
ROUT 74
DES TEST
TKTP TIE
NPID_TBL_NUM 0
ESN NO
CNVT NO
SAT NO
RCLS EXT
DTRK YES
DGTP DTI
ISDN NO
DSEL VCE
PTYP DTT
AUTO NO
DNIS NO
ICOG IAO
SRCH LIN
TRMB YES
STEP
ACOD 7474
TARG 01
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
ANTK
SIGO STD
STYP SDAT
TIMR ICF 512
OGF 512
EOD 4096
DSI 34944
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3
TFD 0
SST 5 0
NEDC ETH
FEDC ETH
CPDC NO
DLTN NO
HOLD 02 02 40
SEIZ 02 02
SVFL 02 02
DRNG NO
CDR NO
MUS NO
RACD NO
MANO NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0


PAGE 002

FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
CBQ NO
AUTH NO
TTBL 0
ATAN NO
OHTD NO
PLEV 2
ALRM NO
ART 0
SGRP 0
AACR NO

Can you pass CLID with E&M trunks and if so what should I change?

Thanks,

Dwayne

 

[bigindian65]

when you say TIE to dialer, is it Agent Audio path, or out to PSTN??

Mato' Was'aka

 

[Avaya911PLM]

Yes, you can assign a CLID to that route via the CLEN prompt.

CLEN 1 is telling the system to use CLID Table 1 for CLID. You can create a CLID Table with a specific number and then change this CLEN value to that CLID Table number.



--
Fletch

Nortel Emergency Services PLM

http://nortel.com/e911

Check out this month's E911 Talk podcast at Nortel E911 Talk Podcast

 

[johnpoole]

you can pass clid on a tie eam if you build it on a digital rdb.. not from an old analog trunk card

john poole
bellsouth business
columbia,sc

 

[johnpoole]

you can't send clid from your loop start home phone.. your provider attaches that to the d on the tdm side of the box

john poole
bellsouth business
columbia,sc

 

[srtelengine]

They term to the Strata Dialer for the agent talk path. CLID is being passed from the LEC to the PBX, but it is from the PBX to the Strata Dialer that the CLID is not being passed.

 

[bigindian65]

If that is Agent Audio path, it has nothing to do with the CLID being passed, it is for the nailed down connection to the dialer app. Have you verified what is coming in on the PRI's to the Dialer? The connection is the dialer. If the dialer is getting it, that is more or less where the agents are.

Mato' Was'aka

 

[Avaya911PLM]

OK, I was backwards. you want to send CLID to the dialer from the PBX? You will need a Digital trunk to do that. (PRI)



--
Fletch

Nortel Emergency Services PLM

http://nortel.com/e911

Check out this month's E911 Talk podcast at Nortel E911 Talk Podcast