Diavox integration and Ring master

[jaylek]

I had upgraded our BC10 TO BC12. Some problems arise after the upgrade. The diavox which we were using for the voice mail functionality was DOS baised and with serial integration. Now there shows some error. While I dial 700 (group number) earlier it promt me for entering the password. Now this is not happening. I am getting this in the serial processor trace as "Framing error in port 2",packet not received from port2. Error alternate p-code instruction.But I can do this way - dial the group700 and press # 'Welcome to diavox ......, please enter your extension... then password... then hear and delete.....
Any body faced this problem / there is any set up required for this?

Please help.

 

[jaylek]

Any help on this ???

 

[VMPOP]

do you use ICU or changed to NIU2 port?
please print and post ICFUP;



East Or West Google Is The Best

 

[doktor]

jaylek!

We are servicing quite a few VMX voice mail servers (VMX/OCTEL/LUCENT/AVAYA) and we are always keeping the ICU/ICU2 board for this integration.
The reason was years ago the lack of quality of the NIU board, that now has improwed much.
But our engineer seem to remember to re-use the old interface boards like ICU/ICU2, because of the stability.
This also goes for the SIU board (SMDR).

Did you swap from ICU to NIU2 ?
doktor

 

[jaylek]

I am using NIU2. Ealier we used NIU.

<ICFUP;
INFORMATION COMPUTER COMMON FUNCTIONS DATA
UPDATING START TIME IS 01:30
MESSAGE WAITING FUNCTIONALITY IS NONE
INFORMATION COMPUTER EQUIPMENT DATA
IFCIND IODEV EQU RATE DFMT UPDFCN PARITY CCHECK
0 NIUVMAIL 5 NO
FILLER=48 ICEXG=NONE USER=NONE
END

<vmpop;
VOICE MAIL PORT DATA
DIR PORT IFCIND
701 00701 0
702 00702 0
703 00703 0
704 00704 0
VOICE MAIL GROUP DATA
GRP IFCIND
700 0
END

<VMFUP;
VOICE MAIL FUNCTION DATA
IFCIND VMF POFMT
0 EXTND 5

 

[jaylek]

Any reply ????

 

[doktor]

To be able to help more - even on a Sunday,
I also need the IODDP;, IONPP; IOIFP; and IONCP;

Your system will never be able to light up MEW lamps.
since "MESSAGE WAITING FUNCTIONALITY IS NONE".
You will need to set it to ALL by: ICFUC:MWF=ALL;

doktor

 

[whosrdaddy]

you have some odd looking port numbers there in the vmpop command, make sure they correspond, so port 1 on your VM system should be marked as port 1 in the md110 (and not 701)

-----------------------------------------------------
What You See Is What You Get
Never underestimate tha powah of tha google!

 

[jaylek]

Hai,
I had changed some setup and the latest print is attached. Please note that with the old setup we were able to use the voicemail function with BC10. Now the system is BC12. We are using Diavox DOS based voice mail.

<ICFUP;
INFORMATION COMPUTER COMMON FUNCTIONS DATA
UPDATING START TIME IS 01:30
MESSAGE WAITING FUNCTIONALITY IS ALL
INFORMATION COMPUTER EQUIPMENT DATA
IFCIND IODEV EQU RATE DFMT UPDFCN PARITY CCHECK
0 NIUVMAIL 5 NO
FILLER=48 ICEXG=NONE USER=NONE
END

<VMPOP;
VOICE MAIL PORT DATA
DIR PORT IFCIND
701 701 0
702 702 0
703 703 0
704 704 0
VOICE MAIL GROUP DATA
GRP IFCIND
700 0
END

<VMFUP;
VOICE MAIL FUNCTION DATA
IFCIND VMF POFMT
0 EXTN2 3
END

<IODDP;
I/O DEVICE DATA
NODE IODEV/SUBFS BPOS/EQU I/O-BUS TYPE/USAGE STATUS AUTH
SYSN - 001-0-60 - - IN SERVICE
SYSN SYSDISK1 001-0-60-0 MASTER TOSHIBA IN SERVICE
SYSSUBFS11
SYSSUBFS21
SYSN SYSTERMINAL 001-0-60-1 - MML - 7
SYSN NIUCIL 001-0-60-2 - OUT IN SERVICE
SYSN NIUVMAIL 001-0-60-3 - OUT IN SERVICE
SYSN TELNET 001-0-60-4 - NETWORK/MML - 7
END

<IONPP;
NETWORK PORT CONFIGURATION DATA
EQU IP GATE MASK ETHERNET
001-0-60-4 192.168.100.70 192.168.100.49 255.255.255.0 00.13.5E.0B.F5.FE
END

<IOIFP;
I/O INTERFACE CHARACTERISTICS
IODEV IFACE BAUDR WORDL PARITY STPBIT PROC
SYSTERMINAL V24 ALL 8 NONE 1 ECHO
NIUCIL V24 9600 8 NONE 1 ECHO
NIUVMAIL V24 9600 7 EVEN 2 ECHO
END

<IONCP;
NETWORKING CONNECTION
NODE/IODEV LIM USER TYPE/CON IP PORT PROC
END

 

[VMPOP]

i advice you to use IFCIND=1 , it's a dump answer but i'm sure it will work,
also in IOEQI don't specify the baudrate and parity and the default setting will be OK for you.

IOEQI:IODEV=NIUVM,EQU=1-xx-xx-xx,USAGE=OUT;
ICFUI:IFCIND=1,.... and complete the rest.

because when you update the channel it will not respond due to a bug in BC12 has been corrected in SP5 and higher.
cheers


East Or West Google Is The Best

 

[jaylek]

The problem is solved. The system is working fine.
Yhanks for all the answers.

 

[jaylek]

The problem is solved. The system is working fine.
Thanks for all the answers.

 

[cfrei]

I think, the best way is catch communication between MD and PC.
Use Telix or Procomm for DOS, or Hyperterminal for Windows, minicom for Linux.
If you dial directly Voice Mail, you should get string
STX82XXXXXZZZ
where STX is ASCII 02,82 is direct internal call, XXXXX 5 digits extension number (ICFUIFMT) and ZZZ is 3 digits port number (VMFUIOFMT)
This is the way from MD to VM.

Way from VM to MD you can test with string:
CTRL-B 06XXXXXYY CTRL-M CTRL-J
where CTRL-B is STX
06 MEW LED on or 07 for MEW LED off
XXXXX extension number
ZZ system number
CTRL-M CTRL-J is CR LF

 

[jaylek]

Good info. Thanks.

 

[doktor]

Nice that you solved it...
doktor