Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations Mike Lewis on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

DeviceTransientConnection Error 1

Status
Not open for further replies.

angelhdz

Technical User
May 2, 2006
18
MX
I'm trying to establish an MGCP connection between a Cisco 2851 and a CCM 4.2 with a Siemmens Hicom 300e.

The router has a NM-HDV2-2T1/E1 in slot 1, and a VWIC-2MFT-E1 in subunit 0.

This is the error I get at the event log in the CallManager

Error: DeviceTransientConnection - Transient connection attempt.
Connecting Port: 2427
Device name [Optional].: *@2851-SLP
Device IP address.: 192.6.5.7
Device type. [Optional]: 254
Reason Code [Optional].: 2
App ID: Cisco CallManager
Cluster ID: StandAloneCluster
Node ID: ccmslp
Explanation: A connection was established and immediately dropped before completing registration. Incomplete registration may indicate a device is rehoming in the middle of registration. The alarm could also indicate a device misconfiguration, database error, or an illegal/unknown device trying to attempt a connection.
Recommended Action: No action is required if this event was issued as a result of a normal device rehome.


Regards
Angel Hernandez
 
What does the router show when you type
"sh ccm-manager config"

Please post. More that likely you have a configuration error.
Also post all your MGCP config from your router.

 
Thanks whykap!!

Here is the show ccm-manager:

2851-SLP#sh ccm-manager
MGCP Domain Name: 2851-SLP
Priority Status Host
============================================================
Primary Domain Name Unresolvable ccmslp
First Backup None
Second Backup None

Current active Call Manager: None
Backhaul/Redundant link port: 2428
Failover Interval: 30 seconds
Keepalive Interval: 15 seconds
Last keepalive sent: 20:06:24 CENTRAL Sep 16 2007 (elapsed time: 3d11h)
Last MGCP traffic time: 15:27:58 CENTRAL Sep 19 2007 (elapsed time: 16:00:33)
Last failover time: None
Last switchback time: None
Switchback mode: Graceful
MGCP Fallback mode: Not Selected
Last MGCP Fallback start time: None
Last MGCP Fallback end time: None
MGCP Download Tones: Disabled

Backhaul/Redundant link is down
Configuration Auto-Download Information
=======================================
Current version-id: {AFA827E9-F4A2-4575-833D-06F62B3893AC}
Last config-downloaded:00:00:00
Current state: Waiting for commands
Configuration Download statistics:
Download Attempted : 1
Download Successful : 1
Download Failed : 0
Configuration Attempted : 1
Configuration Successful : 1
Configuration Failed(Parsing): 0
Configuration Failed(config) : 0
Last config download command: New Registration
FAX mode: cisco
Configuration Error History:
2851-SLP#


And this is the MGCP config...


!
controller E1 1/0/1
pri-group timeslots 1-31 service mgcp
!
interface Serial1/0/1:15
no ip address
encapsulation hdlc
isdn switch-type primary-qsig
isdn incoming-voice voice
isdn bchan-number-order ascending
no cdp enable
!
!
voice-port 1/0/1:15
!
ccm-manager mgcp
ccm-manager music-on-hold
ccm-manager config server 192.168.150.2
ccm-manager config
!
mgcp
mgcp call-agent ccmslp 2427 service-type mgcp version 0.1
mgcp dtmf-relay voip codec all mode out-of-band
mgcp rtp unreachable timeout 1000 action notify
mgcp modem passthrough voip mode nse
mgcp package-capability rtp-package
mgcp package-capability sst-package
mgcp package-capability pre-package
no mgcp package-capability res-package
no mgcp package-capability fxr-package
no mgcp timer receive-rtcp
mgcp sdp simple
mgcp fax t38 inhibit
no mgcp explicit hookstate
mgcp rtp payload-type g726r16 static
!
mgcp profile default
!


Thank you very much!!!!
 
dont use the hostname of the call manager...Use the IP

mgcp call-agent x.x.x.x 2427 service-type mgcp version 0.1

you should also have a redundant host under your ccm-manager config.

ccm-manager config redundant host x.x.x.x (pub)
 
Thank you very much!! I give you a star.

I didn't realized that it had the name instead the IP Address, maybe it change because I have defined a ip name-server on the router.

Now I have another problem, the controller E1 doesn't comes up... maybe is the jumper in the HDV that needs to be changed...

I keep you informed.

Thank you, again.
 
No jumpers.Add this staement to the interface Serial1/0/1:15
ISDN BIND-L3 CCM-Manager
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top