Hello people:
My english is terrible, even so, I will try to be as specific as I can.
I have a Definity S8700 G3v11. I have a T1 link configured in ISDN-PRI (8bzs,esf,Ni2) . I have no problem at all with inbound calls (it works great and it did at the first atemp).
The problem is when I try to set an outbound call. When I trace the station nor the TAC number, I got "denial event 1164: ISDN call reject D2=CV D1=0x8c97 D2=0x260" error message and busy error tone (not fast busy).
I felt free to post also my equipment config, in case somebody could study it a little bit. This is quite important to me get this resolved.
Thanks in advanced to everybody,
Manuel
mcalvo@its.co.cr
________________
>Trace on station 0313 (which is mine) trying to dial out >through tac 862.
LIST TRACE
time data
12:33:27 tone-receiver 04AXX04 cid 0xbcc
12:33:27 active station 0313 cid 0xbcc
12:33:28 dial 862
12:33:28 dial trunk-group 312 cid 0xbcc
12:33:28 dial 862
12:33:28 seize trunk-group 312 member 4 cid 0xbcc
12:33:28 Calling Number & Name 2110313 NO-CPName
12:33:28 denial event 1164: ISDN call reject D2=CV D1=0x8c97 D2=0x260
12:33:28 idle trunk-group 312 member 4 cid 0xbcc
12:33:30 idle station 0313 cid 0xbcc
12:33:39 TRACE COMPLETE station 0313 cid 0x0
_____________
>DS1 config (board 3a12)
Switch name: DEFINITY S8700 - DS1 CIRCUIT PACK
Location: 03A12 Name: T1 ISDN
Bit Rate: 1.544 Line Coding: b8zs
Line Compensation: 1 Framing Mode: esf
Signaling Mode: isdn-pri
Connect: network
TN-C7 Long Timers? n Country Protocol: 1
Interworking Message: PROGress Protocol Version: b
Interface Companding: mulaw CRC? n
Idle Code: 11111111
DCP/Analog Bearer Capability: 3.1kHz
Slip Detection? y Near-end CSU Type: other
Echo Cancellation? y
EC Direction: inward
EC Configuration: 1
DS1 CIRCUIT PACK
ESF DATA LINK OPTIONS
Network Management Protocol: tabs
Send ANSI-T1.403 One-Second Performance Reports? n
Far-end CSU Address: b
__________
>Signaling 312 group config
Switch name: DEFINITY S8700 - SIGNALING GROUP
Group Number: 312 Group Type: isdn-pri
Associated Signaling? y Max number of NCA TSC: 0
Primary D-Channel: 03A1224 Max number of CA TSC: 0
Trunk Group for NCA TSC:
Trunk Group for Channel Selection: X-Mobility/Wireless Type: NONE
Supplementary Service Protocol: a
________________
312 Trunk Group Config
Switch name: DEFINITY S8700 - TRUNK GROUP
Group Number: 312 Group Type: isdn CDR Reports: y
Group Name: PRUEBA T1 ISDN COR: 95 TN: 1 TAC: 862
Direction: two-way Outgoing Display? y Carrier Medium: PRI/BRI
Dial Access? y Busy Threshold: 99 Night Service:
Queue Length: 0
Service Type: public-ntwrk Auth Code? n TestCall ITC: unre
Far End Test Line No:
TestCall BCC: 4
TRUNK PARAMETERS
Codeset to Send Display: 6 Codeset to Send National IEs: 6
Max Message Size to Send: 260 Charge Advice: none
Supplementary Service Protocol: a Digit Handling (in/out): enbloc/enbloc
Trunk Hunt: cyclical QSIG Value-Added? n
Digital Loss Group: 13
Calling Number - Delete: Insert: Numbering Format:
Bit Rate: 1200 Synchronization: async Duplex: full
Disconnect Supervision - In? n Out? n
Answer Supervision Timeout: 0
TRUNK FEATURES
ACA Assignment? n Measured: both Wideband Support? n
Maintenance Tests? y
Data Restriction? n NCA-TSC Trunk Member:
Send Name: y Send Calling Number: y
Used for DCS? n
Suppress # Outpulsing? y Numbering Format: public
Outgoing Channel ID Encoding: preferred UUI IE Treatment: service-provider
Replace Restricted Numbers? n
Replace Unavailable Numbers? n
Send Connected Number: y
Send UUI IE? y
Send UCID? n
Send Codeset 6/7 LAI IE? y Ds1 Echo Cancellation? y
US NI Delayed Calling Name Update? n
SBS? n Network (Japan) Needs Connect Before Disconnect? n
_________________________
My english is terrible, even so, I will try to be as specific as I can.
I have a Definity S8700 G3v11. I have a T1 link configured in ISDN-PRI (8bzs,esf,Ni2) . I have no problem at all with inbound calls (it works great and it did at the first atemp).
The problem is when I try to set an outbound call. When I trace the station nor the TAC number, I got "denial event 1164: ISDN call reject D2=CV D1=0x8c97 D2=0x260" error message and busy error tone (not fast busy).
I felt free to post also my equipment config, in case somebody could study it a little bit. This is quite important to me get this resolved.
Thanks in advanced to everybody,
Manuel
mcalvo@its.co.cr
________________
>Trace on station 0313 (which is mine) trying to dial out >through tac 862.
LIST TRACE
time data
12:33:27 tone-receiver 04AXX04 cid 0xbcc
12:33:27 active station 0313 cid 0xbcc
12:33:28 dial 862
12:33:28 dial trunk-group 312 cid 0xbcc
12:33:28 dial 862
12:33:28 seize trunk-group 312 member 4 cid 0xbcc
12:33:28 Calling Number & Name 2110313 NO-CPName
12:33:28 denial event 1164: ISDN call reject D2=CV D1=0x8c97 D2=0x260
12:33:28 idle trunk-group 312 member 4 cid 0xbcc
12:33:30 idle station 0313 cid 0xbcc
12:33:39 TRACE COMPLETE station 0313 cid 0x0
_____________
>DS1 config (board 3a12)
Switch name: DEFINITY S8700 - DS1 CIRCUIT PACK
Location: 03A12 Name: T1 ISDN
Bit Rate: 1.544 Line Coding: b8zs
Line Compensation: 1 Framing Mode: esf
Signaling Mode: isdn-pri
Connect: network
TN-C7 Long Timers? n Country Protocol: 1
Interworking Message: PROGress Protocol Version: b
Interface Companding: mulaw CRC? n
Idle Code: 11111111
DCP/Analog Bearer Capability: 3.1kHz
Slip Detection? y Near-end CSU Type: other
Echo Cancellation? y
EC Direction: inward
EC Configuration: 1
DS1 CIRCUIT PACK
ESF DATA LINK OPTIONS
Network Management Protocol: tabs
Send ANSI-T1.403 One-Second Performance Reports? n
Far-end CSU Address: b
__________
>Signaling 312 group config
Switch name: DEFINITY S8700 - SIGNALING GROUP
Group Number: 312 Group Type: isdn-pri
Associated Signaling? y Max number of NCA TSC: 0
Primary D-Channel: 03A1224 Max number of CA TSC: 0
Trunk Group for NCA TSC:
Trunk Group for Channel Selection: X-Mobility/Wireless Type: NONE
Supplementary Service Protocol: a
________________
312 Trunk Group Config
Switch name: DEFINITY S8700 - TRUNK GROUP
Group Number: 312 Group Type: isdn CDR Reports: y
Group Name: PRUEBA T1 ISDN COR: 95 TN: 1 TAC: 862
Direction: two-way Outgoing Display? y Carrier Medium: PRI/BRI
Dial Access? y Busy Threshold: 99 Night Service:
Queue Length: 0
Service Type: public-ntwrk Auth Code? n TestCall ITC: unre
Far End Test Line No:
TestCall BCC: 4
TRUNK PARAMETERS
Codeset to Send Display: 6 Codeset to Send National IEs: 6
Max Message Size to Send: 260 Charge Advice: none
Supplementary Service Protocol: a Digit Handling (in/out): enbloc/enbloc
Trunk Hunt: cyclical QSIG Value-Added? n
Digital Loss Group: 13
Calling Number - Delete: Insert: Numbering Format:
Bit Rate: 1200 Synchronization: async Duplex: full
Disconnect Supervision - In? n Out? n
Answer Supervision Timeout: 0
TRUNK FEATURES
ACA Assignment? n Measured: both Wideband Support? n
Maintenance Tests? y
Data Restriction? n NCA-TSC Trunk Member:
Send Name: y Send Calling Number: y
Used for DCS? n
Suppress # Outpulsing? y Numbering Format: public
Outgoing Channel ID Encoding: preferred UUI IE Treatment: service-provider
Replace Restricted Numbers? n
Replace Unavailable Numbers? n
Send Connected Number: y
Send UUI IE? y
Send UCID? n
Send Codeset 6/7 LAI IE? y Ds1 Echo Cancellation? y
US NI Delayed Calling Name Update? n
SBS? n Network (Japan) Needs Connect Before Disconnect? n
_________________________