Hi all,
My first post, so be patient with me please. I've got an Avaya Definity G3 V12 to which I'd like to link an Asterisk server (running Freeswitch). I've found a number of blogs and posts detailing the steps but I'm stuck getting the link to read "in service" on Definity. I've installed a TN464 into the location 01B10. On the Asterisk PC I installed a PhonicEQ Inc. E100P RAVEN E1/PRA Card. I've tried configuring as both a T1 and an E1. I'm having somewhat better luck with E1 as I get an "OK" status in the FreePBX Administration screen:
Here is what I think are the relevant settings in Definity:
[pre]
DS1 CIRCUIT PACK
Location: 01B10 Name: AsteriskLinkAst
Bit Rate: 2.048 Line Coding: hdb3
Signaling Mode: isdn-pri
Connect: line-side
TN-C7 Long Timers? n Country Protocol: 1
Interworking Message: PROGress Protocol Version: b
Interface Companding: mulaw CRC? y
Idle Code: 11111111
DCP/Analog Bearer Capability: 3.1kHz
Slip Detection? n Near-end CSU Type: other
Alarm When PRI Endpoint Detached? y
Block Progress Indicator? n
TRUNK GROUP
Group Number: 4 Group Type: isdn CDR Reports: y
Group Name: Asterisk Link COR: 1 TN: 1 TAC: 204
Direction: two-way Outgoing Display? n Carrier Medium: PRI/BRI
Dial Access? n Busy Threshold: 99 Night Service:
Queue Length: 23
Service Type: tie Auth Code? n TestCall ITC: rest
Far End Test Line No:
TestCall BCC: 4
TRUNK PARAMETERS
Codeset to Send Display: 6 Codeset to Send National IEs: 6
Max Message Size to Send: 260 Charge Advice: none
Supplementary Service Protocol: a Digit Handling (in/out): enbloc/enbloc
Trunk Hunt: descend
Digital Loss Group: 13
Calling Number - Delete: Insert: Numbering Format:
Bit Rate: 1200 Synchronization: async Duplex: full
Disconnect Supervision - In? y Out? n
Answer Supervision Timeout: 0
TRUNK FEATURES
ACA Assignment? n Measured: none Wideband Support? n
Internal Alert? n Maintenance Tests? y
Data Restriction? n NCA-TSC Trunk Member:
Send Name: n Send Calling Number: n
Used for DCS? n
Suppress # Outpulsing? n
Outgoing Channel ID Encoding: preferred UUI IE Treatment: service-provider
Replace Restricted Numbers? n
Replace Unavailable Numbers? n
Send Connected Number: n
Send UUI IE? y
Send UCID? n
Send Codeset 6/7 LAI IE? y Ds1 Echo Cancellation? n
US NI Delayed Calling Name Update? n
SBS? n Network (Japan) Needs Connect Before Disconnect? n
TRUNK GROUP
Administered Members (min/max): 1/30
GROUP MEMBER ASSIGNMENTS Total Administered Members: 30
Port Code Sfx Name Night Sig Grp
1: 01B1001 TN464 F 4
2: 01B1002 TN464 F 4
3: 01B1003 TN464 F 4
4: 01B1004 TN464 F 4
5: 01B1005 TN464 F 4
6: 01B1006 TN464 F 4
7: 01B1007 TN464 F 4
8: 01B1008 TN464 F 4
9: 01B1009 TN464 F 4
10: 01B1010 TN464 F 4
11: 01B1011 TN464 F 4
12: 01B1012 TN464 F 4
13: 01B1013 TN464 F 4
14: 01B1014 TN464 F 4
15: 01B1015 TN464 F 4
TRUNK GROUP
Administered Members (min/max): 1/30
GROUP MEMBER ASSIGNMENTS Total Administered Members: 30
Port Code Sfx Name Night Sig Grp
16: 01B1017 TN464 F 4
17: 01B1018 TN464 F 4
18: 01B1019 TN464 F 4
19: 01B1020 TN464 F 4
20: 01B1021 TN464 F 4
21: 01B1022 TN464 F 4
22: 01B1023 TN464 F 4
23: 01B1024 TN464 F 4
24: 01B1025 TN464 F 4
25: 01B1026 TN464 F 4
26: 01B1027 TN464 F 4
27: 01B1028 TN464 F 4
28: 01B1029 TN464 F 4
29: 01B1030 TN464 F 4
30: 01B1031 TN464 F 4
SIGNALING GROUP
Group Number: 4 Group Type: isdn-pri
Associated Signaling? y Max number of NCA TSC: 0
Primary D-Channel: 01B1016 Max number of CA TSC: 0
Trunk Group for NCA TSC:
Trunk Group for Channel Selection: 4 X-Mobility/Wireless Type: NONE
Supplementary Service Protocol: a
STATUS SIGNALING GROUP
Group ID: 4 Active NCA-TSC Count: 0
Group Type: isdn-pri Active CA-TSC Count: 0
Signaling Type: facility associated signaling
Group State: out-of-service
Primary D-Channel
Port: 01B1016 Level 3 State: out-of-service
Secondary D-Channel
Port: Level 3 State: no-link
[/pre]
This is where I'm stuck. I cannot seem to get passed the "out-of-service" status.
Any ideas would be appreciated. Thank you.
Michael Keen
Southern Vermont College
My first post, so be patient with me please. I've got an Avaya Definity G3 V12 to which I'd like to link an Asterisk server (running Freeswitch). I've found a number of blogs and posts detailing the steps but I'm stuck getting the link to read "in service" on Definity. I've installed a TN464 into the location 01B10. On the Asterisk PC I installed a PhonicEQ Inc. E100P RAVEN E1/PRA Card. I've tried configuring as both a T1 and an E1. I'm having somewhat better luck with E1 as I get an "OK" status in the FreePBX Administration screen:
Here is what I think are the relevant settings in Definity:
[pre]
DS1 CIRCUIT PACK
Location: 01B10 Name: AsteriskLinkAst
Bit Rate: 2.048 Line Coding: hdb3
Signaling Mode: isdn-pri
Connect: line-side
TN-C7 Long Timers? n Country Protocol: 1
Interworking Message: PROGress Protocol Version: b
Interface Companding: mulaw CRC? y
Idle Code: 11111111
DCP/Analog Bearer Capability: 3.1kHz
Slip Detection? n Near-end CSU Type: other
Alarm When PRI Endpoint Detached? y
Block Progress Indicator? n
TRUNK GROUP
Group Number: 4 Group Type: isdn CDR Reports: y
Group Name: Asterisk Link COR: 1 TN: 1 TAC: 204
Direction: two-way Outgoing Display? n Carrier Medium: PRI/BRI
Dial Access? n Busy Threshold: 99 Night Service:
Queue Length: 23
Service Type: tie Auth Code? n TestCall ITC: rest
Far End Test Line No:
TestCall BCC: 4
TRUNK PARAMETERS
Codeset to Send Display: 6 Codeset to Send National IEs: 6
Max Message Size to Send: 260 Charge Advice: none
Supplementary Service Protocol: a Digit Handling (in/out): enbloc/enbloc
Trunk Hunt: descend
Digital Loss Group: 13
Calling Number - Delete: Insert: Numbering Format:
Bit Rate: 1200 Synchronization: async Duplex: full
Disconnect Supervision - In? y Out? n
Answer Supervision Timeout: 0
TRUNK FEATURES
ACA Assignment? n Measured: none Wideband Support? n
Internal Alert? n Maintenance Tests? y
Data Restriction? n NCA-TSC Trunk Member:
Send Name: n Send Calling Number: n
Used for DCS? n
Suppress # Outpulsing? n
Outgoing Channel ID Encoding: preferred UUI IE Treatment: service-provider
Replace Restricted Numbers? n
Replace Unavailable Numbers? n
Send Connected Number: n
Send UUI IE? y
Send UCID? n
Send Codeset 6/7 LAI IE? y Ds1 Echo Cancellation? n
US NI Delayed Calling Name Update? n
SBS? n Network (Japan) Needs Connect Before Disconnect? n
TRUNK GROUP
Administered Members (min/max): 1/30
GROUP MEMBER ASSIGNMENTS Total Administered Members: 30
Port Code Sfx Name Night Sig Grp
1: 01B1001 TN464 F 4
2: 01B1002 TN464 F 4
3: 01B1003 TN464 F 4
4: 01B1004 TN464 F 4
5: 01B1005 TN464 F 4
6: 01B1006 TN464 F 4
7: 01B1007 TN464 F 4
8: 01B1008 TN464 F 4
9: 01B1009 TN464 F 4
10: 01B1010 TN464 F 4
11: 01B1011 TN464 F 4
12: 01B1012 TN464 F 4
13: 01B1013 TN464 F 4
14: 01B1014 TN464 F 4
15: 01B1015 TN464 F 4
TRUNK GROUP
Administered Members (min/max): 1/30
GROUP MEMBER ASSIGNMENTS Total Administered Members: 30
Port Code Sfx Name Night Sig Grp
16: 01B1017 TN464 F 4
17: 01B1018 TN464 F 4
18: 01B1019 TN464 F 4
19: 01B1020 TN464 F 4
20: 01B1021 TN464 F 4
21: 01B1022 TN464 F 4
22: 01B1023 TN464 F 4
23: 01B1024 TN464 F 4
24: 01B1025 TN464 F 4
25: 01B1026 TN464 F 4
26: 01B1027 TN464 F 4
27: 01B1028 TN464 F 4
28: 01B1029 TN464 F 4
29: 01B1030 TN464 F 4
30: 01B1031 TN464 F 4
SIGNALING GROUP
Group Number: 4 Group Type: isdn-pri
Associated Signaling? y Max number of NCA TSC: 0
Primary D-Channel: 01B1016 Max number of CA TSC: 0
Trunk Group for NCA TSC:
Trunk Group for Channel Selection: 4 X-Mobility/Wireless Type: NONE
Supplementary Service Protocol: a
STATUS SIGNALING GROUP
Group ID: 4 Active NCA-TSC Count: 0
Group Type: isdn-pri Active CA-TSC Count: 0
Signaling Type: facility associated signaling
Group State: out-of-service
Primary D-Channel
Port: 01B1016 Level 3 State: out-of-service
Secondary D-Channel
Port: Level 3 State: no-link
[/pre]
This is where I'm stuck. I cannot seem to get passed the "out-of-service" status.
Any ideas would be appreciated. Thank you.
Michael Keen
Southern Vermont College