Hi..anyone farmiliar with a Dees CM-10 call monitor programming, on a Mics 7.1 system. The CM-10 is connected to the system, but when you try to call monitor a line, by entering a COS password, then intercom 7, and then the number for the line i.e 11, I get a message Invalid number...there is no programming info on the CM manual,so seems we need to do some programming on the MICS, Thanks in advance for your relpies.
Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
Dees CM-10 Call monitor
- Thread starter AyaaNort
- Start date
- Thread starter
- #2
curlycord
Programmer
If the display suggests Invalid Number then your issue is is with dialing 7 71 or 711...depends when you get the message.
i.e. if dialing 711 then it thinks your dialing ext/dn 711
Check to see that 7 is a valid Pool or Route #
=----(((((((((()----=
curlycord
Toronto Canada
i.e. if dialing 711 then it thinks your dialing ext/dn 711
Check to see that 7 is a valid Pool or Route #
=----(((((((((()----=
curlycord
Toronto Canada
- Thread starter
- #4
curlycord
Programmer
Put lines into a pool, lets say A
Go to Routes/000 and tell it to use Pool A
Got Dest codes, enter 7 and tell it to use Route 000
=----(((((((((()----=
curlycord
Toronto Canada
Go to Routes/000 and tell it to use Pool A
Got Dest codes, enter 7 and tell it to use Route 000
=----(((((((((()----=
curlycord
Toronto Canada
curlycord
Programmer
looks like the trunks are intercepted to monitor but I don't get how the set communicates with the dees,
i.e 7 would get you a trunk
The guide only shows connections to stations, is this device that smart it connects to any digital port (nortel, nec etc) out there?.
Seems very little info on their guide.
Technical Practice guide?
After so many practices do then get an Install Guide?
I know Dees to make good products but the instructions do not speak curlycord.
I could be out to left field though.
lol?
=----(((((((((()----=
curlycord
Toronto Canada
i.e 7 would get you a trunk
The guide only shows connections to stations, is this device that smart it connects to any digital port (nortel, nec etc) out there?.
Seems very little info on their guide.
Technical Practice guide?
After so many practices do then get an Install Guide?
I know Dees to make good products but the instructions do not speak curlycord.
I could be out to left field though.
lol?
=----(((((((((()----=
curlycord
Toronto Canada
- Thread starter
- #7
Your right about the instructions, none on the programming
Side...the dees is acting as a sniffer device, the
Co lines also get jumped to a bix for the dees, and I'm guessing
The PBX system is only allowing it access when Inercom 7, and the line
code is entered..also there are two pools for the lines A and B, can one route
Be used for both?
Side...the dees is acting as a sniffer device, the
Co lines also get jumped to a bix for the dees, and I'm guessing
The PBX system is only allowing it access when Inercom 7, and the line
code is entered..also there are two pools for the lines A and B, can one route
Be used for both?
curlycord
Programmer
No sorry.
You would need to put the lines into 1 pool.
I get that the code is to choose a line, i dont get is how the Interom of 7 communicates to the Dees.
Is there something else wired up from Dees to KSU besides the trunks?
Example is you dial 7 and it grabs the bottom line of the pool say line 8, how is it a code moves you from line 8 to any other line?.
No way to look at the CICS programming?
=----(((((((((()----=
curlycord
Toronto Canada
You would need to put the lines into 1 pool.
I get that the code is to choose a line, i dont get is how the Interom of 7 communicates to the Dees.
Is there something else wired up from Dees to KSU besides the trunks?
Example is you dial 7 and it grabs the bottom line of the pool say line 8, how is it a code moves you from line 8 to any other line?.
No way to look at the CICS programming?
=----(((((((((()----=
curlycord
Toronto Canada
- Thread starter
- #9
The CICS is toast, so that's not going to help...I'm not sure how intercom 7 was programmed, maybe that's required from the Dees side for access..when you punch in your COS password, and then intercom 7, seems at that point the Dees is coming into play, and when you type in the combination i.e 11 (1+1) for line 2, it will at that point select that line and let the user listen in on the conversation...there is nothing else wired to the trunks, other then the Dees module and power..
norstarboy125
Vendor
Curly is into it, if you could take a look at the cics programming you might get a lead as to which direction to go in.
Jeremy J. Carter
Charm City Communications
Norstar. BCM. CS1000 Programmer
Jeremy J. Carter
Charm City Communications
Norstar. BCM. CS1000 Programmer
Dialing 7 probably accessed a trunk which was the T&R of the observation pair of the Dees unit which is in a trunk group by itself.
All the lines are also tied down on the Dees unit and the selection is made in there.
All the lines are also tied down on the Dees unit and the selection is made in there.
- Thread starter
- #12
Bob, you seem to have the right idea on the functionality of the Dees (dialing intercom 7, did acces a trunk) but the programming seems to be the confusing part, and Dees seems to have done a fine job on not providing any instructions on this.
curlycord
Programmer
So in other words if you want to monitor 8 lines you need a 9th trunk?
=----(((((((((()----=
curlycord
Toronto Canada
=----(((((((((()----=
curlycord
Toronto Canada
The observation pair of the Dees unit ties down as a trunk on the Ksu . By dialing 7 you would access this trunk and be tied into the Dees. All the CO lines that you want to monitor are on the KSU and also tied parallel to the Dees unit. You have codes to move around in the Dees unit. I worked on these about 20 years ago. Theres an 800 number on the pdf Iam sure they could help,
curlycord
Programmer
Thanks Bob
They were/are closed Fridays
I secretly did one as well about same time but my RAM is only 4 megs.
Only programming required is to program a route with dest code or just simple pool with access code on the KSU.
Example if you had 6 lines:
Put observation pair (line 7) into pool C
Make access code C = 7
Allow only supervisor/s access to pool C
or Route method:
Put lines into a pool, lets say A
Go to Routes/000 and tell it to use Pool A
Got Dest codes, enter 7 and tell it to use Route 000
The COS method is:
Restrict line 7 from any digits
Create COS user/slot 00 and password
Tell the user/slot 00 to use filter 02 (not restricted).
You can borrow line 6 and terminate to line 7 to make sure your programming (dialing 7) and that the trunk works (you hear dial tone).
What pair and line number are you using? you sure its correct pin out? amp cable ok?
=----(((((((((()----=
curlycord
Toronto Canada
They were/are closed Fridays
I secretly did one as well about same time but my RAM is only 4 megs.
Only programming required is to program a route with dest code or just simple pool with access code on the KSU.
Example if you had 6 lines:
Put observation pair (line 7) into pool C
Make access code C = 7
Allow only supervisor/s access to pool C
or Route method:
Put lines into a pool, lets say A
Go to Routes/000 and tell it to use Pool A
Got Dest codes, enter 7 and tell it to use Route 000
The COS method is:
Restrict line 7 from any digits
Create COS user/slot 00 and password
Tell the user/slot 00 to use filter 02 (not restricted).
You can borrow line 6 and terminate to line 7 to make sure your programming (dialing 7) and that the trunk works (you hear dial tone).
What pair and line number are you using? you sure its correct pin out? amp cable ok?
=----(((((((((()----=
curlycord
Toronto Canada
- Thread starter
- #16
I had tried to contact Dees on Friday, but there working hours are only Monday to Thursday, while I'm here sometimes working on a weekend, lol.
Thanks Curly and BOb for your detailed comments..
should be able to get it going, and will need to give supervisor access to the sets that need monitoring, will verify connections again when on site.
Thanks Curly and BOb for your detailed comments..
should be able to get it going, and will need to give supervisor access to the sets that need monitoring, will verify connections again when on site.
- Status
Similar threads
- Locked
- Question