Deciphering error codes on 81C

[Judahbenhur69]

Can someone help me decipher the following codes our switch is spitting out?? (every few minutes)

Thanks gang


AUD028 005BBBE9 00000A00 00000000 00000000 00000004 0000341D 00000000 00000000

AUD028 005BEB41 00000A00 00000000 00000000 00000004 00000621 00000000 00000000

AUD335 0 0 005C0EC3 00000C26 00000000 00000000 00000000 0 0 0 00000000 00000000
0000000
0 00000000 00000000 00000000

AUD335 0 0 005D4B2D 00000C26 00000000 00000000 00000000 0 0 0 00000000 00000000
0000000
0 00000000 00000000 00000000

AUD335 0 0 005FC729 00000C26 00000000 00000000 00000000 0 0 0 00000000 00000000
0000000
0 00000000 00000000 00000000

AUD335 0 0 0063F1F9 00000C26 00000000 00000000 00000000 0 0 0 00000000 00000000
0000000
0 00000000 00000000 00000000

AUD335 0 0 006493BB 00000C26 00000000 00000000 00000000 0 0 0 00000000 00000000
0000000
0 00000000 00000000 00000000

AUD028 00655835 00000A00 00000000 00000000 00000004 0000341D 00000000 00000000

AUD017 00000026 0000F77E 0000FFFE

AUD018 00000026 0000FEBE 0000FEFE

AUD019 0000899C 00001070 000002FE

AUD019 000089AC 000010B0 000002FE

AUD019 0000899A 00001068 000002FE

AUD017 00000030 0000F17E 0000F9FE

AUD018 00000030 0000FF9E 0000FFDE

TFS501 38 2 1

TFS501 48 2 1

ERR4057 4277 2277

AUD000

DTC002

TIM950 16:15 23/7/2003 CPU 0

PRI210 DCH: 3 DATA: 00000003
DTC002

 

[PERRYPJ]

THE ONLY ONE THAT I KNOW OF THAT CAN HELP YOU HAS A BANNER AT THE TOP OF THE PAGE, AND IF YOU ASK FLETCH REAL NICE HE MAY TELL YOU ABOUT THE POINTERS AND CALL REGISTERS

OLD ROLMEN WORKING ON NORTELS

 

[Avaya911PLM]

Fletch is heading out for a few relaxing weeks in Lake George and has put the books away. . . BUT . . .

I will tell you that the audit is cleaning up the switch. Something drastic happened (T1 dropped?) This should clear it self up after 10 minutes or so.

I see by the DTC002 you are running on the secondary clock. I'll bet you lost a span, and dropped a bunch of calls. Take a look at Loop 38 and see if things are OK there.(STAT and LCNT)

Your AUD335 are lost call registers floating around being killed.



--
Fletch

http://PBXTech.Net

 

[TDuncan0001]

I have a similar problem on an option 51c.

I keep getting AUD335 messages like this

AUD335 0 0 003FCA0C 00000C26 and then all zero's
AUD335 0 0 003FDE5C 00000C26 and then all zero's

I understand it is a lost call but I am getting 4, 5 or 6 of them on a contiueing basis.

Any ideas?

 

[johnpoole]

do a conv on 003f and 0c26, in ld 32, that one looks like a dtr, bad, test those.. any aud or err codes, at the > prompt

>err aud335... will give you a ballpark pointer to the problem

john poole
bellsouth business
columbia,sc

 

[johnpoole]

read fletch's post very close. if you get groups, with unique tn's then check ld 60 stat, ssck 0, if your getting the same tn, look for a dtr, conf ckt etc. you should (may) get some dropped calls reports, but a lot of aud codes is the switch clearing reg's that are busy but not ref in a connect table.. another thing i have used for trouble shooting, when you get a flood, and don't see lcnt errors, scpu, see if that is side related, tod related, something in common. bad news is that the switch is trying to "hint" that you have a problem, ignore enough hints and she'll tell you a lot louder. (sorta like being married)

john poole
bellsouth business
columbia,sc

 

[TDuncan0001]

When I conv 003f I get error npr601
(tried several variations)
When I conv 0c26 I get 12 0 9 2

The problem is that 12 0 9 is an empty slot. Never has been configured. Never had a card installed.

 

[johnpoole]

almost all your aud codes are mem, instead of port addresses, from the switch conv that is a little eaiser to read, this is the 1st one i saw that might be a pointer


.conv 341d
=> 052 0 07 01

and that doesn't look like a trouble area, have you tested dtr, conf ports?

john poole
bellsouth business
columbia,sc

 

[TDuncan0001]

I am not an expert at this so I am not sure how to do the test you suggested. I had nortel training 10 years ago and have mostly been doing moves, add and changes via MAT software. Can you give me a brief description?

I do appreciate your help. I am trying to nurse the system until it is replaced in about a month.

Thanks

 

[phonedoc]

depending on what release you are on there are patches for the AUD335 errors on Nortels website.
check LD 34 for testing DTR and LD 38 for testing conf.