Tek-Tips is the largest IT community on the Internet today!
Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!
-
Congratulations SkipVought on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!
ddb
- Thread starter krasemeer
- Start date
Try REQ NEW , create the data block then print it out?
It sounds like there is nothing defined to print.
GHTROUT.com | FAQs | Recent Replies
It sounds like there is nothing defined to print.
GHTROUT.com | FAQs | Recent Replies
- Thread starter
- #5
just now i start configure rls 5 pbx, i`ve already created the DDB. but when try to print it to see it i got that error, when try to to add it as :
REQ new
TYPE ddb
SCH203 MEAN : SCH2031
Digital data block already exists.
Iam no configure yet PRI or DTI .
a12ozbottle
Vendor
Are you trying to do this through element manager?
a12ozbottle
Vendor
This is on Nortels Knowledge base.
REQ prt
TYPE ddb
SCH3558
REQ prt
TYPE pri2
FEAT syti
CC DATA NOT 2MB
MEM AVAIL: (U/P): 15671216 USED U P: 6277749 40407 TOT: 21989372
SCH5066
REQ end
>err sch3558
SCH3558
SCD DB LD 73 - No DTI threshold set defined.
Severity: Info
The following actions were taken:
Login to Element Manager. Navigate to Routes and Trunks> Digital Trunk Interface> 2.0Mb Primary Rate Interface (PRI2). At the 2.0Mb Primary Rate Trunk web page, enter the appropriate supl# sh# card number (e.g. 0 1 1). Select the SUBMIT button icon.
A sub-window displays an error:
FEAT
SCH4123
Timers cannot be created.
Enter the 2.0Mb Primary Rate Trunk web page, for a second time. It can be seen that none of the displayed fields have been populated so, the first attempt at configuration was not accepted. Again, enter the appropriate supl# sh# card#, e.g. 0 1 1 Then again, select the SUBMIT button icon. The configuration entry is accepted by EM with no errors.
EXPECTED RESPONSE
=================
The configuration details should be accepted the first time with no errors and the appropriate configuration changes should affect the Call Server.
ACTUAL RESPONSE
===============
1. The first attempt to submit the configuration results in an SCH4123 error.
2. The second attempt to submit the configuration does not result in any error but,the config changes have not affected the Call Server.
DDB after EM attempts to add configuration
-----------------------------------
REQ prt
TYPE ddb
CC DATA NOT 1.5MB
SCH3558
REQ prt
TYPE pri2
FEAT syti
RAIE NO
G1OS YES
SLP 0 0 T 0 0 T
BPV 0 0
CRC 0 0
FAP 0 0
RATS 0
GP2 0 0 T 0 T 0 T 0 T
MNG1 0 T
NCG1 0 T
OSG1 0 T
MNG2 0 T
NCG2 0 T
OSG2 0 T
PERS 0
CLRS 0
OOSC 0
MEM AVAIL: (U/P): 15671216 USED U P: 6277749 40407 TOT: 21989372
SCH5066
REQ
Problem Resolution
Clock controllers must be configured manually using LD73.
REQ prt
TYPE ddb
SCH3558
REQ prt
TYPE pri2
FEAT syti
CC DATA NOT 2MB
MEM AVAIL: (U/P): 15671216 USED U P: 6277749 40407 TOT: 21989372
SCH5066
REQ end
>err sch3558
SCH3558
SCD DB LD 73 - No DTI threshold set defined.
Severity: Info
The following actions were taken:
Login to Element Manager. Navigate to Routes and Trunks> Digital Trunk Interface> 2.0Mb Primary Rate Interface (PRI2). At the 2.0Mb Primary Rate Trunk web page, enter the appropriate supl# sh# card number (e.g. 0 1 1). Select the SUBMIT button icon.
A sub-window displays an error:
FEAT
SCH4123
Timers cannot be created.
Enter the 2.0Mb Primary Rate Trunk web page, for a second time. It can be seen that none of the displayed fields have been populated so, the first attempt at configuration was not accepted. Again, enter the appropriate supl# sh# card#, e.g. 0 1 1 Then again, select the SUBMIT button icon. The configuration entry is accepted by EM with no errors.
EXPECTED RESPONSE
=================
The configuration details should be accepted the first time with no errors and the appropriate configuration changes should affect the Call Server.
ACTUAL RESPONSE
===============
1. The first attempt to submit the configuration results in an SCH4123 error.
2. The second attempt to submit the configuration does not result in any error but,the config changes have not affected the Call Server.
DDB after EM attempts to add configuration
-----------------------------------
REQ prt
TYPE ddb
CC DATA NOT 1.5MB
SCH3558
REQ prt
TYPE pri2
FEAT syti
RAIE NO
G1OS YES
SLP 0 0 T 0 0 T
BPV 0 0
CRC 0 0
FAP 0 0
RATS 0
GP2 0 0 T 0 T 0 T 0 T
MNG1 0 T
NCG1 0 T
OSG1 0 T
MNG2 0 T
NCG2 0 T
OSG2 0 T
PERS 0
CLRS 0
OOSC 0
MEM AVAIL: (U/P): 15671216 USED U P: 6277749 40407 TOT: 21989372
SCH5066
REQ
Problem Resolution
Clock controllers must be configured manually using LD73.
- Thread starter
- #8
- Status
Similar threads
- Locked
- Question