DCH and Loop Association

[Shivrohi]

Hi Everyone

Thanks all in advance

Could someone please tell me how to find which DCH is associated to which loop ?
Please find below the Stat DCH and Stat(loop) info for your reference.

The reason why I am asking this is that I can see ""DCH 029 : OPER RLS"", but I do not know which is loop associated to it so that I can bounce both of them


>ld 96
DCH000
.stat dch
DCH 008 : DSBL RST AUTO DES : Walter_QSIG
DCH 009 : OPER EST ACTV AUTO DES : SIP_D_Channel
DCH 011 : DSBL RST AUTO BKUP 013 DES : Quebec
DCH 012 : DSBL RST AUTO PRIM 012 DES : Quebec
DCH 029 : OPER RLS DES : One_QSIG
DCH 200 : OPER EST ACTV AUTO DES : CSR_QSIG
DCH 201 : OPER EST ACTV AUTO DES : CSR_QSIG


>ld 60
DTI000
.stat

PRI* TRK LOOP 200 - ENBL
FFMT/LCMT/YALMT: ESF/B8Z/FDL
TRACKING
SERVICE RESTORE: YES
YEL ALM PROCESS: YES
ALARM STATUS : NO ALARM
CH 01 - IDLE TIE VOD * CH 02 - IDLE TIE VOD *
CH 03 - IDLE TIE VOD * CH 04 - IDLE TIE VOD *
CH 05 - IDLE TIE VOD * CH 06 - IDLE TIE VOD *
CH 07 - IDLE TIE VOD * CH 08 - IDLE TIE VOD *
CH 09 - IDLE TIE VOD * CH 10 - IDLE TIE VOD *
CH 11 - IDLE TIE VOD * CH 12 - IDLE TIE VOD *
CH 13 - IDLE TIE VOD * CH 14 - IDLE TIE VOD *
CH 15 - IDLE TIE VOD * CH 16 - IDLE TIE VOD *
CH 17 - IDLE TIE VOD * CH 18 - IDLE TIE VOD *
CH 19 - IDLE TIE VOD * CH 20 - IDLE TIE VOD *
CH 21 - IDLE TIE VOD * CH 22 - IDLE TIE VOD *
CH 23 - IDLE TIE VOD * CH 24 - DCH 201

PRI* TRK LOOP 201 - ENBL
FFMT/LCMT/YALMT: ESF/B8Z/FDL
SERVICE RESTORE: YES
YEL ALM PROCESS: YES
ALARM STATUS : NO ALARM
CH 01 - IDLE TIE VOD * CH 02 - IDLE TIE VOD *
CH 03 - IDLE TIE VOD * CH 04 - IDLE TIE VOD *
CH 05 - IDLE TIE VOD * CH 06 - IDLE TIE VOD *
CH 07 - IDLE TIE VOD * CH 08 - IDLE TIE VOD *
CH 09 - IDLE TIE VOD * CH 10 - IDLE TIE VOD *
CH 11 - IDLE TIE VOD * CH 12 - IDLE TIE VOD *
CH 13 - IDLE TIE VOD * CH 14 - IDLE TIE VOD *
CH 15 - IDLE TIE VOD * CH 16 - IDLE TIE VOD *
CH 17 - IDLE TIE VOD * CH 18 - IDLE TIE VOD *
CH 19 - IDLE TIE VOD * CH 20 - BUSY TIE VOD *
CH 21 - BUSY TIE VOD * CH 22 - BUSY TIE VOD *
CH 23 - BUSY TIE VOD * CH 24 - DCH 202

PRI* TRK LOOP 219 - ENBL
FFMT/LCMT/YALMT: ESF/B8Z/FDL
SERVICE RESTORE: YES
YEL ALM PROCESS: YES
ALARM STATUS : YELLOW
CH 01 - DSBL TIE VOD * CH 02 - DSBL TIE VOD *
CH 03 - DSBL TIE VOD * CH 04 - DSBL TIE VOD *
CH 05 - DSBL TIE VOD * CH 06 - DSBL TIE VOD *
CH 07 - DSBL TIE VOD * CH 08 - DSBL TIE VOD *
CH 09 - DSBL TIE VOD * CH 10 - DSBL TIE VOD *
CH 11 - DSBL TIE VOD * CH 12 - DSBL TIE VOD *
CH 13 - DSBL TIE VOD * CH 14 - DSBL TIE VOD *
CH 15 - DSBL TIE VOD * CH 16 - DSBL TIE VOD *
CH 17 - DSBL TIE VOD * CH 18 - DSBL TIE VOD *
CH 19 - DSBL TIE VOD * CH 20 - DSBL TIE VOD *
CH 21 - DSBL TIE VOD * CH 22 - DSBL TIE VOD *
CH 23 - DSBL TIE VOD * CH 24 - DCH 30

PRI* TRK LOOP 225 - ENBL
FFMT/LCMT/YALMT: ESF/B8Z/FDL
TRACKING
SERVICE RESTORE: YES
YEL ALM PROCESS: YES
ALARM STATUS : NO ALARM
CH 01 - MBSY TIE VOD * CH 02 - MBSY TIE VOD *
CH 03 - MBSY TIE VOD * CH 04 - MBSY TIE VOD *
CH 05 - MBSY TIE VOD * CH 06 - MBSY TIE VOD *
CH 07 - MBSY TIE VOD * CH 08 - MBSY TIE VOD *
CH 09 - MBSY TIE VOD * CH 10 - MBSY TIE VOD *
CH 11 - MBSY TIE VOD * CH 12 - MBSY TIE VOD *
CH 13 - MBSY TIE VOD * CH 14 - MBSY TIE VOD *
CH 15 - MBSY TIE VOD * CH 16 - MBSY TIE VOD *
CH 17 - MBSY TIE VOD * CH 18 - MBSY TIE VOD *
CH 19 - MBSY TIE VOD * CH 20 - MBSY TIE VOD *
CH 21 - MBSY TIE VOD * CH 22 - MBSY TIE VOD *
CH 23 - MBSY TIE VOD * CH 24 - DCH 9

PRI* TRK LOOP 235 - DSBL
FFMT/LCMT/YALMT: ESF/B8Z/FDL
PRI* TRK LOOP 236 - DSBL
FFMT/LCMT/YALMT: ESF/B8Z/FDL
PRI* TRK LOOP 237 - DSBL
FFMT/LCMT/YALMT: ESF/B8Z/FDL



Please suggest.

 

[bignose21]

Loops to Physical card slots in case of the CS1000E are seen in LD 22
REQ prt
TYPE cequ

Then DCH to Loops are seen in LD 22
REQ prt
TYPE adan dch

in the DCH print outs you see DCHL specifying the Loop the DCH is associated with

here are some examples from a US CS1000E system

In the CEQU you see DLOP for T1 and the Frame settings etc., if elsewhere E1 is under PRI2

DLOP NUM DCH FRM TMDI LCMT YALM T1TE TRSH MG_CARD
PRI 050 24 ESF YES B8S FDL 0 00 008 0 01
051 24 ESF YES B8S FDL 0 00 008 0 02

ADAN DCH shows

ADAN DCH 50
CTYP TMDI
MG_CARD 008 0 01 <----Physical Card for the DCH, with CS1000E TMDI its going to match the PRI
PORT 1 <------Port on the DCH card with TMDI/MSDL of a CS1000E it will be port 1, MSDL on CS1000M it could be a 4 port MSDL card so ports 0-3
DES UX1_P1_2
USR PRI
DCHL 50 <----------The Loop
OTBF 32
PARM RS232 DTE

 

[MossEng]

Also if you look at the LD 60 STAT, Channel 24 for each Loop shows the assigned DCH.

PRI* TRK LOOP 200 - ENBL
FFMT/LCMT/YALMT: ESF/B8Z/FDL
TRACKING
SERVICE RESTORE: YES
YEL ALM PROCESS: YES
ALARM STATUS : NO ALARM
CH 01 - IDLE TIE VOD * CH 02 - IDLE TIE VOD *
CH 03 - IDLE TIE VOD * CH 04 - IDLE TIE VOD *
CH 05 - IDLE TIE VOD * CH 06 - IDLE TIE VOD *
CH 07 - IDLE TIE VOD * CH 08 - IDLE TIE VOD *
CH 09 - IDLE TIE VOD * CH 10 - IDLE TIE VOD *
CH 11 - IDLE TIE VOD * CH 12 - IDLE TIE VOD *
CH 13 - IDLE TIE VOD * CH 14 - IDLE TIE VOD *
CH 15 - IDLE TIE VOD * CH 16 - IDLE TIE VOD *
CH 17 - IDLE TIE VOD * CH 18 - IDLE TIE VOD *
CH 19 - IDLE TIE VOD * CH 20 - IDLE TIE VOD *
CH 21 - IDLE TIE VOD * CH 22 - IDLE TIE VOD *
CH 23 - IDLE TIE VOD * CH 24 - DCH 201

 

[Shivrohi]

Thanks much bignose21 and MossEng .

 

[Shivrohi]

As you guys see, there is a YELLOW alarm in one of the loops and the status is not changing even after bouncing it. I disable the dch first and then disable and enable the loop as it is the process. But the status is remain unchanged.

PRI* TRK LOOP 219 - ENBL
FFMT/LCMT/YALMT: ESF/B8Z/FDL
SERVICE RESTORE: YES
YEL ALM PROCESS: YES
ALARM STATUS : YELLOW
CH 01 - DSBL TIE VOD * CH 02 - DSBL TIE VOD *
CH 03 - DSBL TIE VOD * CH 04 - DSBL TIE VOD *
CH 05 - DSBL TIE VOD * CH 06 - DSBL TIE VOD *
CH 07 - DSBL TIE VOD * CH 08 - DSBL TIE VOD *
CH 09 - DSBL TIE VOD * CH 10 - DSBL TIE VOD *
CH 11 - DSBL TIE VOD * CH 12 - DSBL TIE VOD *
CH 13 - DSBL TIE VOD * CH 14 - DSBL TIE VOD *
CH 15 - DSBL TIE VOD * CH 16 - DSBL TIE VOD *
CH 17 - DSBL TIE VOD * CH 18 - DSBL TIE VOD *
CH 19 - DSBL TIE VOD * CH 20 - DSBL TIE VOD *
CH 21 - DSBL TIE VOD * CH 22 - DSBL TIE VOD *
CH 23 - DSBL TIE VOD * CH 24 - DCH 30

 

[Shivrohi]

The reason why I am doing it, there is a number which is giving fast busy dial tone. There are three strange things I found

1. I could not find the number in IDC
2. I could not even locate the number in Adaptations
3. When I check the local number tied to it, it is a phantom number and call forwarding is enabled for a different number which is reachable.


Number I am dialing is 4167583118 (3118 - local internal number) - condigured on a Phantom Number - DCFW 91xxxxxxxxxx


Please let me know if there is anything I am missing or I need to check.


Regards