gaendalf
IS-IT--Management
- May 28, 2009
- 2
Hello,
I am trying to create a backup machine for our alphaserver 4100
OS DEC Unix 4.0B
old machine alpha 4100
"new" alphaserver DS20e
filesystem advfs.
What is done:
backup to tape the root_domain usr_domain from 4100
sreated root_domain, usr_domain an DS20E, data restored.
what i'd like to get:
DEC Unix running,
what igot: (see below)
Resetting I/O buses...
(boot dkc0.0.0.8.0 -flags A)
block 0 of dkc0.0.0.8.0 is a valid boot block
reading 32 blocks from dkc0.0.0.8.0
bootstrap code read in
base = 200000, image_start = 0, image_bytes = 4000(16384)
initializing HWRPB at 2000
initializing page table at 3ff42000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code
Digital UNIX boot - Fri Nov 13 13:15:46 EST 1998
Loading vmunix ...
Loading at 0xfffffc0000230000
Current PAL Revision <0x2004f00010162>
Switching to OSF PALcode Succeeded
New PAL Revision <0x2004a0002015c>
Sizes:
text = 4364416
data = 743008
bss = 1527776
Starting at 0xfffffc000052fa90
Loading vmunix symbol table ... [1243552 bytes]
Alpha boot: available memory from 0x2304000 to 0x3ff40000
Digital UNIX V4.0E (Rev. 1091); Sun Jun 20 10:35:49 MET DST 1999
physical memory = 1024.00 megabytes.
available memory = 988.32 megabytes.
using 1307 buffers containing 10.21 megabytes of memory
Master cpu at slot 0.
Firmware revision: 7.3-1
PALcode: Digital UNIX version 1.92-74
COMPAQ AlphaServer DS20E 666 MHz
mcpcia_adpt_cnfg: eisa bridge found but no assoc. bus struct foud
eisa bridge setup not done
pci1 at mcbus0 slot 5
gpc0 at eisa0
pci0 at mcbus0 slot 4
panic (cpu 0): mcbusconfl: get_bus pci, -1, * -99 failed
DUMP: No primary swap, no explicit dumpdev.
Nowhere to put header, giving up.
CP - SAVE_TERM routine to be called
CP - SAVE_TERM exited with hlt_req = 1, r0 = 00000000.00000000
halted CPU 0
halt code = 5
HALT instruction executed
PC = fffffc0000531620
CPU 0 booting
Resetting I/O buses...
and so on...
does anybody knows what can i try to eliminate this problem?
Thanks a lot for your advices.
I am trying to create a backup machine for our alphaserver 4100
OS DEC Unix 4.0B
old machine alpha 4100
"new" alphaserver DS20e
filesystem advfs.
What is done:
backup to tape the root_domain usr_domain from 4100
sreated root_domain, usr_domain an DS20E, data restored.
what i'd like to get:
DEC Unix running,
what igot: (see below)
Resetting I/O buses...
(boot dkc0.0.0.8.0 -flags A)
block 0 of dkc0.0.0.8.0 is a valid boot block
reading 32 blocks from dkc0.0.0.8.0
bootstrap code read in
base = 200000, image_start = 0, image_bytes = 4000(16384)
initializing HWRPB at 2000
initializing page table at 3ff42000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code
Digital UNIX boot - Fri Nov 13 13:15:46 EST 1998
Loading vmunix ...
Loading at 0xfffffc0000230000
Current PAL Revision <0x2004f00010162>
Switching to OSF PALcode Succeeded
New PAL Revision <0x2004a0002015c>
Sizes:
text = 4364416
data = 743008
bss = 1527776
Starting at 0xfffffc000052fa90
Loading vmunix symbol table ... [1243552 bytes]
Alpha boot: available memory from 0x2304000 to 0x3ff40000
Digital UNIX V4.0E (Rev. 1091); Sun Jun 20 10:35:49 MET DST 1999
physical memory = 1024.00 megabytes.
available memory = 988.32 megabytes.
using 1307 buffers containing 10.21 megabytes of memory
Master cpu at slot 0.
Firmware revision: 7.3-1
PALcode: Digital UNIX version 1.92-74
COMPAQ AlphaServer DS20E 666 MHz
mcpcia_adpt_cnfg: eisa bridge found but no assoc. bus struct foud
eisa bridge setup not done
pci1 at mcbus0 slot 5
gpc0 at eisa0
pci0 at mcbus0 slot 4
panic (cpu 0): mcbusconfl: get_bus pci, -1, * -99 failed
DUMP: No primary swap, no explicit dumpdev.
Nowhere to put header, giving up.
CP - SAVE_TERM routine to be called
CP - SAVE_TERM exited with hlt_req = 1, r0 = 00000000.00000000
halted CPU 0
halt code = 5
HALT instruction executed
PC = fffffc0000531620
CPU 0 booting
Resetting I/O buses...
and so on...
does anybody knows what can i try to eliminate this problem?
Thanks a lot for your advices.