CS1Ke adding an MGC and TMDI clock question

[RossV]

I've added an MGC and have it functioning. I am adding three PRI circuits on three TMDI cards. I have a TMDI in slot 1 with a clock controller on it. I've programmed my route/trunks and dchannels all per the specs telco has given me and I can enable/disable and force download the TMDI firmware so I know I'm talking with it. The MGC is up and running no sweat but I go into ld 73 and try to add the clock and I get sch124. I've tried it with the TMDI enabled and disabled and it doesn't seem to matter. I don't have the circuits turned up yet but I didn't think it mattered to add a clock controller. Any ideas on what I might be missing to get it to take the new clock. I'm pretty confident I'm inputting the right shelf/card info into the DDB when I get the SCH code. I'm on release 5.
MEM AVAIL: (U/P): 96017756 USED U P: 7885931 348726 TOT: 104252413
DISK SPACE NEEDED: 683 KBYTES
REQ prt

TYPE ddb


MGCLK 0 1 1
PREF 0 1 1
SREF 0 1 2
MGCLK 4 0 1
PREF 4 0 1
SREF
MGCLK 4 1 1
PREF 4 1 1
SREF
MGCLK 8 0 1
PREF 8 0 1
SREF

TRSH 00
RALM 3
BIPC 0
LFAC 0
BIPV 3 2
SRTK 5 30
SRNT 5 3
LFAL 17 511
SRIM 1
SRMM 2
ICS


REQ chg

TYPE ddb

MGCLK 12 0 1

PREF 12 0 1
SCH0124
PREF SCH0124
PREF
SREF
CEQU:
ld 22

PT2000

REQ prt

TYPE cequ


CEQU
MPED 8D
TERM
REMO
TERD
REMD
TERQ
REMQ
SUPL V000 V004 V008 V012
V096 V100 V104 V108
N112 V156
SUPC
SUPF
XCT
CONF
MGTDS IPMG IPMG_TYPE
126 000 1 MGC
128 004 0 MGC
130 004 1 MGC
132 008 0 MGC
134 012 0 MGC
MGCONF IPMG PORTS IPMG_TYPE
127 000 1 30 MGC
129 004 0 30 MGC
131 004 1 30 MGC
133 008 0 30 MGC
135 012 0 30 MGC
MFSD * 126 * 128 * 130 * 132
* 134

DLOP NUM DCH FRM TMDI LCMT YALM T1TE TRSH MG_CARD
TRK 055 00 D4 YES B8S DG2 0 00 000 1 04
087 00 D4 YES B8S DG2 0 00 004 1 03
PRI 052 23 ESF YES B8S FDL 0 00 000 1 01
053 23 ESF YES B8S FDL 0 00 000 1 02
054 23 ESF YES B8S FDL 0 00 000 1 03
076 23 ESF YES B8S FDL 0 00 004 0 01
077 24 ESF YES B8S FDL 0 00 004 0 02
078 23 ESF YES B8S FDL 0 00 004 0 03
085 24 ESF YES B8S FDL 0 00 004 1 01
116 23 ESF YES B8S FDL 0 00 008 0 01
118 23 ESF YES B8S FDL 0 00 012 0 01
120 23 ESF YES B8S FDL 0 00 012 0 02
122 23 ESF YES B8S FDL 0 00 012 0 03
MISP MG_CARD
EXT0 3PE
EXT1 3PE
MCFN 011 MB

 

[RossV]

bump

 

[Tman45]

Well ... I haven't programmed a clock controller but your SCH is:

SCH0124 Card out of range.
Action:
Severity: Info. Critical to Monitor: No. SNMP trap: No

Here is ours and it has 12 0 1:

>ld 73
DDB000
MEM AVAIL: (U/P): 97850666 USED U P: 5934031 467716 TOT: 104252413
DISK SPACE NEEDED: 791 KBYTES
REQ prt
TYPE ddb

MGCLK 4 0 1
PREF 4 0 1
SREF 4 0 2
MGCLK 8 0 1
PREF 8 0 1
SREF 8 0 2
MGCLK 12 0 1
PREF 12 0 1
SREF 12 0 2
MGCLK 16 0 1
PREF 16 0 1
SREF 16 0 2
MGCLK 20 0 1
PREF 20 0 1
SREF
MGCLK 52 0 1
PREF 52 0 1
SREF 52 0 2
MGCLK 56 0 1
PREF 56 0 1
SREF 56 0 2
MGCLK 60 0 1
PREF 60 0 1
SREF 60 0 2

TRSH 00
RALM 128
BIPC 0
LFAC 0
BIPV 3 2
SRTK 5 30
SRNT 15 3
LFAL 17 511
SRIM 1
SRMM 2
ICS


REQ