CS1K is not sending CLID to Asterisk via TieLine

[minicompbx]

thread798-910063

I am having exaclty the same issue as the thread mention above.
In sum, I have installed Asterisk and it is connected to CS1K via TIELINE. Everything is working but when I call from Nortel to Asterisk extension, it show 10 digit number instead of local 4 digit DN and Name

Below is my prinout of RDB

TYPE RDB  
CUST 00 
ROUT 44 
DES  ASTERISK
TKTP TIE 
M911P NO 
ESN  NO  
CNVT NO  
SAT  NO  
RCLS INT 
VTRK NO  
DTRK YES 
BRIP NO  
DGTP PRI 
ISDN YES 
    MODE PRA 
    IFC  ESS5
    SBN  NO
    PNI  00000 
    SRVC WATB
    SRPM 0 
    NCNA YES 
    NCRD NO  
    CHTY BCH 
    CTYP UKWN
    INAC NO  
    ISAR NO  
    CPUB OFF 
    DAPC NO  
    BCOT 0 
MBXR NO  
MBXOT NPA 
MBXT 0 
DSEL VOD 
PTYP PRI 
CNDP UKWN 
AUTO NO  
DNIS NO  
DCDR NO  
ICOG IAO 
SRCH RRB 
TRMB YES 
STEP 
ACOD ****
TCPP NO  
PII NO  
AUXP NO  
TARG 
CLEN 1 
BILN NO
OABS 
INST 
IDC  NO  
DCNO 0 *
NDNO 0 
DEXT NO  
ANTK 
SIGO STD 
ICIS YES
TIMR ICF  512 
     OGF  512 
     EOD  13952 
     NRD  10112 
     DDL  70 
     ODT  4096 
     RGV  640 
     GRD  896 
     SFB  3 
     NBS  2048 
     NBL  4096 
     TFD  0 
DRNG NO  
CDR  NO  
MUS  NO  
RACD NO  
FRL  0 0 
FRL  1 0 
FRL  2 0 
FRL  3 0 
FRL  4 0 
FRL  5 0 
FRL  6 0 
FRL  7 0 
AUTH NO  
TTBL 0 
ATAN NO  
PLEV 2 
ALRM NO  
ART  0 
SGRP 0 
ARDN NO  
CTBL 0 
AACR NO

Let me know you need any more information
Thank's

Learning is not enough, you have to apply it...

 

[jamie2]

If you can build the as a QSIG (ISGF), it will make your life a lot easier!

 

[minicompbx]

I thought the same thing as lot of people saying that too.. But it is possible to fix without needing to change IFC to QSIG
Because in that case, I have to remove the dch and trunk and recreate it.

Thank's

Learning is not enough, you have to apply it...

 

[jamie2]

You'll have to out and rebuild everything again, but its only a 5-15 minute task.

 

[minicompbx]

I did have some time today ... so I did remove the DCH adn TRUNK
When trying to create ADAN, it give me the error

IFC  ISGF
>err sch6670
SCH6670
QSIGGF package is restricted.

Learning is not enough, you have to apply it...

 

[yyrkroon]

Your switch doesn't have the QSIG package - unless it's release 7.0, maybe 7.5 or higher, I don't think you can get packages without upgrading.

 

[minicompbx]

Actually, I am using Rls 7.0 unless my vendor mislead me ?

Learning is not enough, you have to apply it...

 

[yyrkroon]

Call your vendor, tell them you need to add package 305 and 263 to the PBX - they either come back with a ok and ask for a little money or we need to talk and ask for a lot of money, because you'll have to upgrade to get the package.

 

[yyrkroon]

Or see if the A can emulate SL1 protocol or try NI2 if it's capable.

 

[minicompbx]

I did rebuild with SL1 and what do I have to setup for Asterisk Side

On Nortel side, everything seem working but call does not pass thourgh astersik

Before, I was able to make a call to Nortel <--> Asterisk. Now, nothing is working

Stat of loop :

.stat **

PRI*  TRK  LOOP ** - ENBL 
FFMT/LCMT/YALMT:  ESF/B8Z/FDL 
SERVICE RESTORE: YES 
YEL ALM PROCESS: YES 
ALARM STATUS : NO ALARM
CH 01 - IDLE TIE   VOD  *           CH 02 - IDLE TIE   VOD  *          
CH 03 - IDLE TIE   VOD  *           CH 04 - IDLE TIE   VOD  *          
CH 05 - IDLE TIE   VOD  *           CH 06 - IDLE TIE   VOD  *          
CH 07 - IDLE TIE   VOD  *           CH 08 - IDLE TIE   VOD  *          
CH 09 - IDLE TIE   VOD  *           CH 10 - IDLE TIE   VOD  *          
CH 11 - IDLE TIE   VOD  *           CH 12 - IDLE TIE   VOD  *          
CH 13 - IDLE TIE   VOD  *           CH 14 - IDLE TIE   VOD  *          
CH 15 - IDLE TIE   VOD  *           CH 16 - IDLE TIE   VOD  *          
CH 17 - IDLE TIE   VOD  *           CH 18 - IDLE TIE   VOD  *          
CH 19 - IDLE TIE   VOD  *           CH 20 - IDLE TIE   VOD  *          
CH 21 - IDLE TIE   VOD  *           CH 22 - IDLE TIE   VOD  *          
CH 23 - IDLE TIE   VOD  *           CH 24 - DCH **

stat of dch

DCH 0** : OPER       EST   ACTV  AUTO         DES : ASTERISK

output of rdb :

TYPE RDB  
CUST 00 
ROUT ** 
DES  ASTERISK
TKTP TIE 
M911P NO 
ESN  NO  
CNVT NO  
SAT  NO  
RCLS INT 
VTRK NO  
DTRK YES 
BRIP NO  
DGTP PRI 
ISDN YES 
    MODE PRA 
    IFC  SL1 
    PNI  00001 
    NCNA YES 
    NCRD YES 
    TRO  NO  
    CHTY BCH 
    CTYP UKWN
    INAC NO  
    ISAR NO  
    DAPC NO  
MBXR NO  
MBXOT NPA 
MBXT 0 
DSEL VOD 
PTYP PRI 
CNDP UKWN 
AUTO NO  
DNIS NO  
DCDR NO  
ICOG IAO 
SRCH LIN 
TRMB YES 
STEP 
ACOD ****
TCPP NO  
PII NO  
AUXP NO  
TARG 
CLEN 1 
BILN NO
OABS 
INST 
IDC  YES 
DCNO 0 
NDNO 0 *
DEXT NO  
DNAM NO  
ANTK 
SIGO STD 
ICIS YES
TIMR ICF  512 
     OGF  512 
     EOD  13952 
     NRD  10112 
     DDL  70 
     ODT  4096 
     RGV  640
     GRD  896 
     SFB  3 
     NBS  2048 
     NBL  4096 
     TFD  0 
DRNG NO  
CDR  YES 
INC  YES 
LAST NO
QREC NO  
OAL  NO  
MUS  NO  
RACD NO  
FRL  0 0 
FRL  1 0 
FRL  2 0 
FRL  3 0 
FRL  4 0 
FRL  5 0 
FRL  6 0 
FRL  7 0 
AUTH NO  
TTBL 0 
ATAN NO  
PLEV 2 
ALRM NO  
ART  0 
SGRP 0 
ARDN NO  
CTBL 0 
AACR NO

Each time that I tried make a call., I get
When Calling from Asterisk to Nortel :

DCH ** IMSG SETUP    REF 00008004 CH 0 TOD  17:43:55 
CALLING #:1122           NUM PLAN: E164/NATIONAL / NPA 
CALLED  #:6622           NUM PLAN: E164/NATIONAL / NPA 

    DCH ** OMSG REL COMP REF 00008004 CH 0 TOD  17:43:55 
CAUSE :INCOMING CALL BARRED   
DIAG: 199 
PRI227 DCH: ** DATA: 00000004

And calling from Nortel to Asterisk

  DCH ** OMSG SETUP    REF 00000017 CH ** 23 TOD  18:04:25 
FEAT :NCID
PROGRESS: ORIG ADDR IS NOT ISDN 
CALLING #:6622           NUM PLAN: PRIVATE/RESERVED (LOC) 
CALLED  #:1122           NUM PLAN: PRIVATE/UNKNOWN (UNKNOWN) 


    DCH ** OMSG RELEASE  REF 00000017 CH 0 TOD  18:04:25 
CAUSE :INVALID IE CONTENTS

    DCH ** IMSG CALLPROC REF 00008017 TOD  18:04:25 
PRI222 DCH: ** DATA: 00000017 
    DCH ** IMSG REL COMP REF 00000017 CH ** 23 TOD  18:04:25 
CAUSE :NORMAL CALL CLEARING

Thank's

Learning is not enough, you have to apply it...

 

[minicompbx]

LCNT ld 60 log

TRSH CNT:
BPV     -000 
SLIPD   -000 
SLIPR   -000 
CRC     -000 
LOSFA   -005 
OS_BPV  -000 
OS_LOSFA-002 
OS_YEL  -000

Learning is not enough, you have to apply it...

 

[jamie2]

If you can't do QSIG, then do NI2. SL1 is proprietary for Nortel

 

[minicompbx]

You mean for the configuration of CS1K, I reconfigure the DCH with NI2 instead of SL1




Learning is not enough, you have to apply it...

 

[minicompbx]

By the way, is there a way I can find out which packages are installed on my system.
Thank's


Learning is not enough, you have to apply it...

 

[jamie2]

<code>
>ld 22
REQ prt
TYPE pkg
</code>

 

[jamie2]

<code>
>ld 22
REQ prt
TYPE pkg
</code>

 

[minicompbx]

Is it really hard or huge cost to add new package because I already have 263 but not 305

Learning is not enough, you have to apply it...

 

[KCFLHRC]

Your not going to get the 4 digit # and name unless it's Nortel to Nortel with SL1 for the IFC.

 

[minicompbx]

So to connect to Asterisk, I have to use QSIG ???

Learning is not enough, you have to apply it...

 

[KCFLHRC]

QSIG still is not going to send the LD 95 name across the network, just doesn't work except Nortel to Nortel. Depending on your release on the PBX you may or may not even be able to get the required packages for QSIG. The name info and name format is proprietary to Nortel. I have never seen it work with QSIG or any other protocol other than Nortel to Nortel.