Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

CS1K can't enable loop urgent..!

Status
Not open for further replies.

MefistoAplasta

Programmer
May 31, 2009
62
DO
I'm trying to install a new T1 loop but when I want to enable the loop I received the error message:

ld 60
enll 28
ERROR: DTI012 28

The card is brand new and I tried with a old one too with the same result:

I checked the status and I got this:
=================================

LD 32
028 = DTI TRK LOOP
DSBL NOT RESPONDING NPR301

LD 60
stat 28
DTI TRK LOOP 28 - DSBL
FFMT/LCMT/YALMT: D4/ AMI/DG2

What I did:
===========
LD 17
CHG
CEQU
DLOP 28 24 D4
TYPE TRK
TRASH 00
DTIC: <enter>

ld 16
REQ: prt
TYPE: rdb
CUST 0
ROUT10
TYPE RDB
CUST 00
ROUT 10
DES OCS
TKTP DID
M911_ANI NO
M911_TONE NO
NPID_TBL_NUM 0
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK YES
BRIP NO
DGTP DTI
ISDN NO
DSEL VCE
PTYP DCO
AUTO NO
DNIS NO
ICOG IAO
RANX NO
SRCH LIN
TRMB YES
STEP
ACOD 2396
TARG 02 03 04 05 06 07
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
MFC NO
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GTO 896
GTI 896
SFB

IENB 5
VSS 0
VGD 6
SST 5 0
DTD NO
SCDT NO
2 DT NO
NEDC ORG
FEDC ORG
CPDC NO
DLTN NO
HOLD 02 02 40
SEIZ 02 02
SVFL 02 02


PAGE 002

DDO NO
DRNG NO
CDR NO
NATL YES
SSL
CFWR NO
IDOP NO
VRAT NO
MUS NO
MR NO
PANS YES
RACD NO
MANO NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TDET NO
TTBL 0
ATAN NO
OHTD NO
PLEV 2
OPR NO
PRDL NO
EOS NO
DNSZ 0
RCAL NO
MCTS NO
ALRM NO
BTT 30
ACKW NO
ART 0
TIDY 2396 10
SGRP 0
CCBA NO
ARDN NO
AACR NO

LD 14
NEW 24
DID
TN 28 1
DATE
PAGE
DES

DES OCS T1
TN 028 01
TYPE DID
CUST 0
TRK DTI
PDCA 1
PCML
PCML
RTMB 10 1
NITE
SIGL EM4
STRI/STRO WNK WNK
SUPN YES
AST NO
IAPG 0
CLS UNR DTN ECD WTA LPR APN THFD HKD
P10 VNL
TKID
DTCR NO
AACR NO
DATE 26 JUN 2009



 
nevermind, didn't see that the old card is doing this too
 
What slot are you in on the Media Gateway?
Perhaps try a different one if available?

DTI0012 x Network loop/card x pack does not respond from IOTEST; loop/card x is
disabled.
Action:
Severity: Info. Critical to Monitor: Yes. SNMP trap: Yes

NPR0301 loop Loop is a Digital Trunk Interface or Primary Rate Interface.
Action: Use LD 60.
Severity: Minor. Critical to Monitor: Yes. SNMP trap: No
 
What system/RLS do you have? It might be that you cannot use Loop 28?
 
now is working, I forgot to press the enable/disable switch :p
Thanks for the response
 
Hey new to the forum hope someone can help. We have a CS1K i replaced the Fibre Recive vard and now the 2 of the fibre recive cards are not comingup and the Digital line cards are also not coming up. What can i do too solve this problem if andthing.
 
Junioriof - you should post a new thread with your issue.

When you replaced the fibre receive card what errors did you get on the PBX? What symptoms did you have before that made you replace the old fibre card?
 
had electrical issues no power comin gto fibre card will post new thread thanks
sorry about that
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top