CS1000M number translation problem 2

[Aerodesliza]

What is the best way to perfom number translation for H323 trunking between BCM and CS1000? for example:

I call 1XXX - YYY - ZZZZ ;where ZZZ is my station
I want translate that to:

LOC + DN

 

[bigindian65]

you can do "Off-Net to On-Net" number recognition, so you have UDP setup between the sites with LOC in place?

Mato' Was'aka

 

[Aerodesliza]

yes I have UDP setup between the sites with LOC in place, how work the Off-Net to On-Net?

 

[bigindian65]

actually that applies to outgoing TIE, so maybe not the right APP. You could SPN xxx yyy, and DMI to del npa nxx and insert loc-DN

Mato' Was'aka

 

[Aerodesliza]

But I can do that with LOC, right? the problem is Im only able to use 3 digit location number and my NPA is always the same that means I can't make a difference between two site:

SiteA: 888 123 XXXX, where NPA=888=LOC NXX=123
SiteB: 888 456 XXXX, where NPA=888=LOC NXX=456

I saw that I can use a npa and nxx parameter in the location setup but I don't know how to use them.

 

[Aerodesliza]

any idea?

 

[bigindian65]

it looks like you could make a difference if you had SPN 888123 and SPN 888456

Mato' Was'aka

 

[Avaya911PLM]

You can accomplish this in NARS/BARS.

Build the NPA as an SPN with ARRN entries for your NXX range. Point that to an RLI that strips the 1-NPA-NXX and inserts LOC-XXXX on the H.323 route, then as a second entry in that RLI point to the PSTN with no DMI.

--
Fletch

Nortel Emergency Services PLM

http://nortel.com/e911

Check out this month's E911 Talk podcast at Nortel E911 Talk Podcast

 

[Aerodesliza]

Good idea, I will try it

 

[Aerodesliza]

I tried but does't work maybe because my CS 1000 H323 setup if for Location network not for SPN, I got this not SPN:

Calling from 2155:
------------------

RIG TN 004 0 05 08 KEY 0 SCR MARP CUST 0 DN 2155 TYPE 3903
TERM NONE
DIAL DN 99995407444
CALL ID 460 1911

PROGRESS: ORIG ADDR IS NOT ISDN
CALLING #:2155 NUM PLAN: PRIVATE/UNKNOWN (UNKNOWN)
CALLED #:233 NUM PLAN: PRIVATE/NETWORK SPECIFIC (SPN)

DCH 10 IMSG CALLPROC REF 000001B8 CH 148 0 1 23 TOD 14:26:50

 

[Lynx77]

You can change the call type in NRS entries. They should match the call type in the PABX

 

[Aerodesliza]

If I want to use SPN instead of LOC, what I need to change in NRS?

 

[Aerodesliza]

any idea?

 

[Lynx77]

When you use SPN in the PABX, the routing entry in NRS should be of type Private special.

 

[Aerodesliza]

Lynx77 you're a genius, Thanks

 

[Aerodesliza]

The CS1000 outgoing dialing plan is working but the BCM's outgoing dialing plan is not, what I have to set for the BCM to use the SPN plan instead of the LOC plan, I think that is my issue.

 

[Aerodesliza]

any idea?

 

[Aerodesliza]

any help?

 

[Aerodesliza]

I tried to change the BCM private network to CDP instead of UDP, maybe CDP is for SPN plan, but didn't work, Im reciving a busy tone, Im using SPN lenght=10 but the Private newtwork only allow me 7 digit,could it be problem? anyone could give me some advice.

 

[Aerodesliza]

somebody could give me some advice