Hello all you paging experts out there. I am officially at a point of exasperation! I am hooking up a Valcom V-2003A multi page unit to a PAG port in the CS1000. However, I am only using it for single zone paging. I connect my buttset to the port and hear my page fine from a 3904. When I connect my buttset to the speaker output of the Valcom (R/BL - BL/R), I get nothing. I have the page port connected to W/BL - BL/W of the Valcom.
On the Valcom I have SW1 and SW5 up, SW2 up, and SW3 all are up (the book says this is off for all.)
Here is my programming for RDB and PAG:
DES PAGING
TN 000 0 04 07 VIRTUAL
TYPE PAG
CUST 0
XTRK XUT
TIMP 600
BIMP 3COM
RTMB 5 1
SIGL LDR
STRO WNK
SUPN NO
AST NO
IAPG 0
CLS UNR DTN CND ECD WTA LPR THFD SPCD
P10 NTC
AACR NO
DATE 25 AUG 2012
REQ: prt
TYPE: rdb
CUST 0
ROUT 5
TYPE RDB
CUST 00
ROUT 5
DES PAG
TKTP PAG
NPID_TBL_NUM 0
NACC PGNR
ESN NO
VTRK NO
CNDP UKWN
ICOG OGT
SRCH LIN
STEP
ACOD 6973
TARG
CLEN 1
OABS
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3
TFD 0
SST 5 0
NEDC ETH
FEDC ORG
HOLD 02 02 40
SEIZ 02 02
RGFL 02 02
CDR NO
MUS NO
TTBL 0
OHTD NO
ALRM NO
ART 0
SGRP 0
ARDN NO
CTBL 0
AACR NO
I have tried the WAT route option, but get a pause then busy. I have studied the manual
and search this knowledge base for hours. I am at the mercy of this forum. Please Tek-Tippers Help!!
Thank you all ahead of time!
On the Valcom I have SW1 and SW5 up, SW2 up, and SW3 all are up (the book says this is off for all.)
Here is my programming for RDB and PAG:
DES PAGING
TN 000 0 04 07 VIRTUAL
TYPE PAG
CUST 0
XTRK XUT
TIMP 600
BIMP 3COM
RTMB 5 1
SIGL LDR
STRO WNK
SUPN NO
AST NO
IAPG 0
CLS UNR DTN CND ECD WTA LPR THFD SPCD
P10 NTC
AACR NO
DATE 25 AUG 2012
REQ: prt
TYPE: rdb
CUST 0
ROUT 5
TYPE RDB
CUST 00
ROUT 5
DES PAG
TKTP PAG
NPID_TBL_NUM 0
NACC PGNR
ESN NO
VTRK NO
CNDP UKWN
ICOG OGT
SRCH LIN
STEP
ACOD 6973
TARG
CLEN 1
OABS
TIMR ICF 512
OGF 512
EOD 13952
DSI 34944
NRD 10112
DDL 70
ODT 4096
RGV 640
GRD 896
SFB 3
TFD 0
SST 5 0
NEDC ETH
FEDC ORG
HOLD 02 02 40
SEIZ 02 02
RGFL 02 02
CDR NO
MUS NO
TTBL 0
OHTD NO
ALRM NO
ART 0
SGRP 0
ARDN NO
CTBL 0
AACR NO
I have tried the WAT route option, but get a pause then busy. I have studied the manual
and search this knowledge base for hours. I am at the mercy of this forum. Please Tek-Tippers Help!!
Thank you all ahead of time!