CS1000 User license

[Hyder1988]

Hi everyone,

New to the switch, I just received 100 new user license how do I upload into the system. I just received licences in an E-mail and not sure how to upload into the system.

Thank you so much..

 

[Hyder1988]

forgot to add they are VOIP licenses.

 

[Hyder1988]

sorry doing a search for installing license, so I wanted to add a few more things.

I already have 50 VOIP license installed and working.

I don't have vendor support so I will have to do it all manually.

They sent me the license in a email, not sure if I need to do anything special to get license from email to the switch. ready somewhere that I need them on the CF card, how do I get them to that card.

Thanks again..

 

[Firebird Scrambler]

You need to put the licence keycode in a folder called "keycode" on the external CF card. Log into the system and go into LD 143. The instructions below are old, but should still apply for you.

Instant ISM Upgrade Feature Operation
Feature operation is further broken down into three options:
Instant ISM parameter upgrade using a keycode diskette or CF Card for large systems

Instant ISM parameter upgrade using a keycode diskette / CF Card for large systems
For options 51C, 61C, 81, and 81C systems, perform the following to instantly activate a
keycode without a Sysload:
Note: For a dual-CPU (redundant) system, leave the system in full redundant mode (hard
disk and CPU redundancy).

1. Log in on a system terminal and load overlay 143.
LD 143
CCBROOO
2. Insert the new keycode diskette / CF card into the floppy drive on the active IODU/C.
3. Enter the KDIF command and select keycode comparison options.
.KDIF REC FO or KDIF REC CF2
The new keycode option is shown in bold.
Note: In the following example, the (REC) currently used keycode will be compared with
the new keycode disk in floppy drive FO. The limits shown are for example purposes only.
Validating Keycode File /p/install/keycode.rec ... OK

Validating Keycode File /fO/keycode.kcd ... OK
System parameters 1st keycode: 2nd keycode:
System Serial Number: 46XX 46XX
Software Version: 2911 2911
System Type: Option 61C Option 61C
Call Processor: CP68060E CP68060E
Release: 24 24
issue: XX XX
NTI Order Number:
NT SDID-1:
NT SDID-2:

Date and Time of Manufacture:
Note: () indicates that information is not available
ISM Limits in the 1 st keycode: 2nd keycode:
Loop Limit: 32 32
Sys TNs Limit: 2000 3500
ACDAgt Limit: 10 10
ACD DNs Limit: 10 10
AST Limit: 10 10
Common packages for both keycodes:
0-2 4-5 7-25 28-29 32-55 58-65
Additional packages in the 2nd keycode:
Additional packages in the 2nd keycode:
4. Select the new keycode for activation using the KNEW command.
.KNEW FO or KNEW CF2

If the new keycode is eligible for instant activation (which is the case in the above example
since only the TN limits has increased!) it will be activated without further user action, and
the following system message is given:
CCBR020 New Keycode accepted and activated successfully. Sysload is NOT needed!
Otherwise, if the keycode is not eligible for instant activation, a Sysload is needed to
activate the new keycode and the following system message is given:
CCBR009 New Keycode accepted. It will be activated during the next restart.





All the best

Firebird Scrambler
Meridian 1 / Succession and BCM / Norstar Programmer in the UK

http://www.linkedin.com/in/davidbromley

If it's working, then leave it alone!.

 

[Hyder1988]

Thank you very much, just what I needed...