Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

  • Congratulations strongm on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Cs1000 release 6 Analogue trunk disconnection

Status
Not open for further replies.

Swampfire

Programmer
Sep 27, 2010
13
GB
I have a cs100 release 6 using 12 analogue trunks accross 2x NT5k18ab cards when people hang up it takes around 30 seconds for the system to release the trunk again is this normal or is there something I can change I have tried supn-yes but still the same line type is lDC Thanks for your response
 
Are the trunks ground start? If not they need changed to ground start to work properly in a CS1000. I don't know what a NT5K18AB card actually is, I have always used and NT8D14 Universal Trunk Card.
 
Hi the line type is COT THE SIGNAL TYPE IS LDC ROUTE AND TRUNK BELOW BT say line should be unguarded clear & their disconnect clear timer is 500ms


TYPE RDB
CUST 00
ROUT 101
DES HOSTEDVOICE
TKTP COT
NPID_TBL_NUM 0
PRIV NO
RPA NO
SAT NO
RCLS EXT
VTRK NO
NODE
DTRK NO
ISDN NO
PTYP ACO
AUTO YES
ACMP NO
ICOG IAO
RANX NO
SRCH RRB
TRMB YES
STEP
ACOD 6
TARG
CLEN 1
BILN NO
OABS
TIMR ICF 384
OGF 384
EOD 13952
LCT 256
DSI 384
NRD 10112
DDL 70
OOD 3
ODT 4096
RGV 256
FLH 510
GTO 2944
GTI 2944
ARP 3
SFB 3
CRD 384
TFD 0
LEXT 100
SST 3 0
DTD NO
SCDT NO
2 DT NO
NEDC ETH
FEDC ETH
CPDC NO
SPCT IMM
HOLD 02 02 40
SEIZ 02 02
RGFL 02 02
RVSD 08 31
ILLR 02 02
DDO NO
DRNG YES
NDRI 00
CDR NO
NATL YES


PAGE 002

SSL
CFWR NO
IDOP NO
MUS NO
MR NO
PANS YES
MANO NO
EQAR NO
FRL 0 0
FRL 1 1
FRL 2 2
FRL 3 3
FRL 4 4
FRL 5 5
FRL 6 6
FRL 7 7
TTBL 0
ATAN NO
OHTD NO
PLEV 2
OPR YES
RCAL NO
MCTS NO
ALRM NO
ART 0
PECL NO
DCTI 0
TIDY 1600 101
SGRP 0
ARDN NO
AACR NO

REQ:
DES HV
TN 008 0 01 00 VIRTUAL
TYPE COT
CUST 0
XTRK XCOT
FWTM NO
BIMP 3COM
TRK ANLG
NCOS 5
RTMB 101 1
ATDN 3802
SIGL LDC
SUPN YES
AST NO
IAPG 0
BTID 0
CLS UNR DTN CND ECD WTA LPR APN THFD BARD SPCD
P10 LOL
TKID
AACR NO
DATE 16 SEP 2011
 
Have you tried going through a maintenace set and placing a call? Or better yet take a butt set and hop on a trunk at the dmarc. Place a call there without the switch connected.
 
I have done that and it's fine managed to get sorted chnaged signal type to ldr and dsi timer to 128 disconnects straight away thanks for responding
 
I have the same issue. Vendor told me analog trunks are not supported on the CS1000 6.0 and we converted to TMDI PRI. Works fine now.
 
Status
Not open for further replies.

Part and Inventory Search

Sponsor

Back
Top