Connecting a Shoretel to a Nortel on 25.40

[19austintech50]

I am working on a customer that has an old 81C and they bought a Shortel. They want to call from Dallas on their Shortel throught the Austin Shortel and out the local T1's on the Nortel to make local calls.I can call from the Nortel to the Dallas Shortel and out locally in Dallas, but when they call from Dallas to Austin the call fails. We get reorder tone. On the Tie between the Shortel and the Nortel, D Channel messaging says "unassigned number". I have turn on Trunk to Trunk but I can not get it to work. They don't have the QSIG package on the Nortel, so the Tie is built at NI2. Any ideas anyone.

TYPE RDB
CUST 00
ROUT 19
DES SHORETEL
TKTP DID
NPID_TBL_NUM 0
SAT NO
RCLS EXT
DTRK YES
DGTP PRI
ISDN YES
MODE PRA
IFC NI2
CBCR NO
NCOS 0
SBN NO
PNI 00000
NCNA YES
NCRD NO
CHTY BCH
CPFXS NO
HNTN
HLCL
CPUB OFF
DAPC NO
BCOT 0
INTC NO
DSEL 3VCE
PTYP PRI
AUTO NO
DNIS NO
DCDR NO
ICOG IAO
RANX NO
SRCH LIN
TRMB YES
STEP
ACOD 7019
TCPP NO
PII NO
TARG
CLEN 1
BILN NO
OABS
INST
IDC NO
DCNO 0 *
NDNO 0
DEXT NO
ICIS YES
TIMR ICF 512
OGF 512
EOD 13952
NRD 10112
DDL 70
ODT 4096
RGV 640
FLH 510
GRD 896
SFB 3
NBS 2048
NBL 4096
TFD 0


PAGE 002

DRNG NO
CDR NO
MUS NO
RACD NO
EQAR NO
FRL 0 0
FRL 1 0
FRL 2 0
FRL 3 0
FRL 4 0
FRL 5 0
FRL 6 0
FRL 7 0
OHQ NO
OHQT 00
TTBL 0
ATAN NO
PLEV 2
MCTS NO
ALRM NO
ART 0
SGRP 0
AACR NO

REQ: ****
OVL000
>ld 22
PT2000

REQ prt
TYPE adan dch 2

ADAN DCH 2
CTYP MSDL
GRP 0
DNUM 8
PORT 2
DES SHORETEL
USR PRI
DCHL 19
OTBF 32
PARM RS422 DTE
DRAT 64KC
CLOK EXT
IFC NI2
ISDN_MCNT 300
CLID OPT0
CO_TYPE STD
SIDE NET
CNEG 1
RLS ID 1
RCAP NCT COLP
T310 120
T200 3
T203 10
N200 3
N201 260
K 7
BSERV NO

REQ ****
OVL000
>ld 20

PT0000
REQ: prt
TYPE: tnb
TN 19 1
SPWD
DATE
PAGE
DES

DES SHORETEL
TN 019 01
TYPE DID
CDEN SD
CUST 0
TRK PRI
PDCA 1
PCML MU
NCOS 0
RTMB 19 1
B-CHANNEL SIGNALING
NITE
STRI/STRO OWK OWK
AST NO
IAPG 0
CLS UNR DTN CND WTA LPR APN THFD HKD
P10 VNL
TKID
DATE 21 JAN 2013

 

[KCFLHRC]

I'm thinking your NCOS 0 is probably the culprit in the route and trunks. Set it as high as a set would be to make the same call.

 

[janaya]

We tried this, but ultimately we had to use straight T1 programming (No Dchannel) to get it to work. It is up and working fine like this, just no CLID information.

 

[19austintech50]

Checked NCOS on all trunks and they were set to 0.

I have been told they can't be DID and I ahave been told they can't be TIE. Same animal, different color.

 

[KCFLHRC]

They should be built TIE with an NCOS on the route and trunks high enough to match the FRL in the RLI to place the call. An NCOS of 0 is probably restricting everything but internal calls.

 

[guycable2]

I don't have a switch with that old of software but I have seen this issue on our 6.0 and newer systems and we had to turn DITI to yes in NET_DATA.

Not sure what release DITI was added.