Connect External lines to Hipath 4k v1

[RonyKassam]

Hello ,
I have Siemens Hipath 4000 v1 with the following modules:
1- TMOM2 Q2214X100 qty=1
2- SLMA24 Q2246X qty=54
3- TM2LP Q2159X160 qty=12
4- SLMO Q2168X qty=4
5- LTUCX Q2166X qty=5
6- SIUX2 Q2187X qty=3
7- DIUN2 Q2196X qty=2
8- HUBC Q2143X qty=1
9- QDCL Q2113X100 qty=2
10-SICOE Q2234X100 qty=2
11-MTSCG Q2224X1 qty=2
12-DPC5 Q2270X100 qty=3

For Test purpose, How can I connect two external lines (from PSTN) to Hipath? which module? what are the commands needed to use the external lines from any internal line?

For main purpose, I need 100 external lines, I have prepared Fiber cable from the CO to Hipath, can I connect the fiber directly to Hipath? if not, how can I prepare 100 external lines? what are the commands needed?

I hope your response
Thanks

 

[sbcsu]

Hi,
Make the LDPLN
5-W-X-X

Make the LODR
ECHO 3
ECHO 4
END

Try dialling out and putting # at the end when you dial out

If that fails try dialling out directly on the Line again using a test phone.

When you dial out via the HiPath does the light flash on the TM2LP card ?

 

[RonyKassam]

<ADD-LDPLN:5-W-X-X,0&1&2&3&4&5&6&7&8&9&10&11&12&13&14&15,1,,1,,,,N;
ADD-LDPLN:5-W-X-X,0&1&2&3&4&5&6&7&8&9&10&11&12&13&14&15,1,,1,,,,N;
H500: AMO LDPLN STARTED
H07: LDP HAS BEEN ADDED

AMO-LDPLN-111 ADMINISTRATION LCR DIALPLAN
ADD COMPLETED;
<DISPLAY-LODR;
DISPLAY-LODR;
H500: AMO LODR STARTED
+-------------------------------------------------------+
| ODR POSITION CMD PARAMETER |
+--------+----------------------------------------------+
| 1 | 1 ECHO 3 |
| | 2 ECHO 4 |
| | 3 END |
+--------+----------------------------------------------+
|INFO:ODR FOR CALLS ON ANALOGUE LINES |
+-------------------------------------------------------+

AMO-LODR -111 ADMINISTRATION OF LCR OUTDIAL RULES
DISPLAY COMPLETED;

when dialing out and putting # .. success, I get call correctly.
but without putting # ... failed, I get busy tone after 10 seconds
Yes the LED of TM2LP card flashing.

 

[sbcsu]

OK so it is working but you have to put the # at the end.
It is likely that your timers are incorrect.

REG-PTIME;
COPY-PTIME:87,0;
COPY-PTIME:51,1;
COPY-PTIME:87,2;

 

[RonyKassam]

<COPY-PTIME:51,1;
COPY-PTIME:51,1;
H500: AMO PTIME STARTED
F03: BLOCK 1 IS ASSIGNED TO THE TRUNK CIRCUIT WITH THE PEN 1-1-61-0.
F03: BLOCK 1 IS ASSIGNED TO THE TRUNK CIRCUIT WITH THE PEN 1-1-61-1.

AMO-PTIME-111 TIMERS FOR PERIPHERAL PROCESSING
COPY NOT COMPLETED;
<

what I have to do?

 

[sbcsu]

Try reloading the TM2LP Card
Either take it out and put it in again or type in
RES-BSSUEN,1,1,61;

The problem is that the system needs to be setup in a logical order.
That order includes setting timer blocks to each card depending on the territory/country where you are.

 

[RonyKassam]

OK my teacher,
I did
RES-BSSUEN,1,1,61;
but I get the same result.

I think I have to delete the trunks, and do the PTIME commands, after that rewrite the configuration of the trunks.

 

[RonyKassam]

Finally, It is solved.
when I read TM2LP documentation, I found that its signalling is DP, DTMF.
After that I read the documentation of "trunking for rest of the world"
I found that I have to add NO1A to COP of the trunks.
Also, I used 5-W-X-X as DPLN.

Thanks sbcsu, you are a great teacher.

 

[sbcsu]

Well done Rony
A lot of configurations are standard depending on your location.
Happy you got it sorted out.

How are the Operators - is that ok ?

 

[RonyKassam]

Thanks sbcsu,
about console ..
see the last post in the thread

http://www.tek-tips.com/viewthread.cfm?qid=1746847